| EEPROMlessModeSupported = 1 # 0 = disable epromless support / 1 = Enable |
| WME_Enable = 1 # 0 = diable WME support / 1 = Enable |
| dot11NetworkType = 3 # 2 - A only mode, 3 - B/G mode, 4 - A/G Dual mode |
| RecoveryEnable = 1 # 0 - Disabled, 1 - Enabled |
| TriggerFcs = 0 # 0 - Disabled, 1 - Enabled |
| dot11FragmentationThreshold = 4096 |
| dot11RTSThreshold = 4096 |
| WPAMixedMode = 1 |
| RSNPreAuthentication = 1 |
| |
| CalibrationChannel24 = 1 |
| CalibrationChannel5 = 36 |
| |
| # Regulatury Domain tables. |
| # Each byte correlates to one channel in sequential order. Table 2.4 starts from channel 1, Table 5.0 starts from channel 36. |
| # Bits 0..4 - Max power allowed in Dbm. |
| # Bit 6 - Channel is allowed for Active scan |
| # BIt 7 - Channel is allowed |
| AllowedChannelsTable24 = FFFFFFFFFFFFFFFFFFFFFFFFFFFF |
| AllowedChannelsTable5 = FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF0000000000000000000000000000000000000000000000000000000000000000000000FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF000000FF0000000000000000FF000000FF000000FF000000FF00000000000000000000000000000000000000 |
| |
| |
| |
| SpectrumManagement = 0 # 0 - Disable 802.11h, 1 - Enable |
| |
| RxBroadcastInPs = 1 |
| |
| FirstConnScanEnabled = 1 # 0 - Disable , 1 - Enable |
| |
| #arp ip filter |
| ArpIp_Addr = c0 a8 00 5e |
| ArpIp_Filter_ena = 0 |
| |
| |
| #mac filter |
| Mac_Filter_Enabled = 0 |
| numGroupAddrs = 4 |
| Group_addr0 = 10 01 02 03 04 05 |
| Group_addr1 = 11 11 12 13 14 15 |
| Group_addr2 = 12 21 22 23 24 25 |
| Group_addr3 = 13 31 32 33 34 35 |
| Group_addr4 = 14 41 42 43 44 45 |
| Group_addr5 = 15 51 52 53 54 55 |
| Group_addr6 = 16 61 62 63 64 65 |
| Group_addr7 = 17 71 72 73 74 75 |
| |
| #beacon filter |
| Beacon_Filter_Desired_State = 1 |
| Beacon_Filter_Stored = 1 |
| |
| #beacon IE table |
| #the size is the len of the string - spaces = number of bytes |
| Beacon_IE_Num_Of_Elem = 15 |
| Beacon_IE_Table_Size = 35 |
| Beacon_IE_Table = 00 01 01 01 32 01 2a 01 03 01 06 01 07 01 20 01 25 01 23 01 30 01 28 01 2e 01 85 01 dd 00 52 f2 02 00 01 |
| |
| #Rate adaptation |
| RateContThreshold = 10 |
| RateStepUpThreshold = 2 |
| FBShortInterval = 40 |
| FBLongInterval = 200 |
| RateAdaptationTimeout = 300 |
| |
| # rate policy - short / long retries |
| RatePolicyUserShortRetryLimit = 10 |
| RatePolicyUserLongRetryLimit = 10 |
| |
| #rate policies |
| RatePolicyUserRetriesPerRateCck = 1,1,1,1,1,1,1,1,1,1,1,1,1 |
| RatePolicyUserRetriesPerRatePbcc = 1,1,1,1,1,1,1,1,1,1,1,1,1 |
| RatePolicyUserRetriesPerRateOfdm = 0,0,0,1,0,0,0,1,0,0,1,1,1 |
| RatePolicyUserRetriesPerRateOfdmA = 0,0,0,1,0,0,1,0,0,1,0,0,0 |
| |
| RatePolicySGRetriesPerRateCck = 1,1,1,1,1,1,1,5,1,1,1,1,1 |
| RatePolicySGRetriesPerRatePbcc = 1,1,1,1,1,1,1,5,1,1,1,1,1 |
| RatePolicySGRetriesPerRateOfdm = 1,1,1,1,1,1,1,5,1,1,1,1,1 |
| RatePolicySGRetriesPerRateOfdmA = 1,1,1,1,1,1,1,5,1,1,1,1,1 |
| |
| # |
| # Power Manager |
| # |
| BeaconListenInterval = 1 # the number of N-Beacon or N-DTim |
| DtimListenInterval = 1 # Dm: Different value causes DHCP problem |
| |
| dot11PowerMode = 0 # 0 - Auto |
| # 1 - Active |
| # 2 - Short Doze |
| # 3 - Long Doze |
| |
| PowerMgmtHangOverPeriod = 5 # in mSec units |
| |
| AutoPowerModeDozeMode = 2 # 2 - Short Doze |
| # 3 - Long Doze |
| |
| AutoPowerModeActiveTh = 15 # packets per second |
| |
| AutoPowerModeDozeTh = 8 # packets per seconds - threshold for entering ELP in Auto mode |
| |
| |
| |
| defaultPowerLevel = 0 # 0 - ELP |
| # 1 - PD |
| # 2 - AWAKE |
| |
| PowerSavePowerLevel = 0 # 0 - ELP |
| # 1 - PD |
| # 2 - AWAKE |
| |
| |
| OsDbgState = 0x01e9003c # -1 or 0xffffffff -all (opens debug messages in o.s. only - sevirity+modules) |
| |
| ############################################################# |
| # Configure the severity table (0 = Disable/ 1 = Enable) |
| # |
| # Byte #0: Init |
| # Byte #1: Information |
| # Byte #2: Warning |
| # Byte #3: Error |
| # Byte #4: Fatal Error |
| # Byte #5: SM |
| # Byte #6: Console |
| # Byte #7: Debug RX |
| # Byte #8: Debug TX |
| # Byte #9: Debug Control |
| # Byte #10: Debug GWSI Recording |
| ############################################################# |
| |
| ReportSeverityTable = "00011010000" |
| |
| |
| BeaconReceiveTime = 50 |
| |
| # |
| # Default Driver Scan Parameters for BG band |
| # |
| FirstConnScanBandB_ChannelList = 1,2,3,4,5,6,7,8,9,10,11,12,13,14 # channel list to scan seperated with comma |
| FirstConnScanBandB_MinDwellTime = 30000 # Min dwell time in micro seconds |
| FirstConnScanBandB_MaxDwellTime = 60000 # Max dwell time in micro seconds |
| FirstConnScanBandB_NumOfProbReqs = 3 # Number of prob request |
| FirstConnScanBandB_ProbReqRate = 2 # Prob request rate |
| FirstConnScanBandB_TxPowerLevel = 255 # Tx power for every prob request - Dbm/10 units |
| |
| # Default Driver Scan Parameters for A band |
| FirstConnScanBandA_ChannelList = 36,40,44,48,52,56,60,64,100,104,108,112,149,153,157,161 # channel list to scan seperated with comma |
| FirstConnScanBandA_MinDwellTime = 30000 # Min dwell time in micro seconds |
| FirstConnScanBandA_MaxDwellTime = 60000 # Max dwell time in micro seconds |
| FirstConnScanBandA_NumOfProbReqs = 3 # Number of prob request |
| FirstConnScanBandA_ProbReqRate = 32 # Prob request rate |
| FirstConnScanBandA_TxPowerLevel = 255 # Tx power for every prob request - Dbm/10 units |
| |
| # |
| # QOS UPSD |
| # |
| |
| desiredPsMode = 0 # Global Power save delivery protocol (1 - UPSD, 0 - Legacy) |
| QOS_wmePsModeBE = 0 # Power save delivery protocol for BE AC (1 - UPSD, 0 - Legacy) |
| QOS_wmePsModeBK = 0 # Power save delivery protocol for BK AC (1 - UPSD, 0 - Legacy) |
| QOS_wmePsModeVI = 0 # Power save delivery protocol for VI AC (1 - UPSD, 0 - Legacy) |
| QOS_wmePsModeVO = 0 # Power save delivery protocol for VO AC (1 - UPSD, 0 - Legacy) |
| |
| # QOS_PacketBurstEnable = 1 # Packet Burst for non-QOS protocol |
| |
| # |
| # QOS Classifier |
| # |
| Clsfr_Type = 1 # 1 - DSCP, 2 - Port, 3 - IP+port |
| |
| NumOfDstIPPortClassifiers = 3 # number of classifier entries |
| |
| IPPortClassifier00_IPAddress = 0a 03 89 02 # IP address 10.3.137.2 |
| IPPortClassifier00_Port = 5001 # Port 5001 |
| IPPortClassifier00_DTag = 1 # User priority 1 |
| |
| IPPortClassifier01_IPAddress = 0a 03 89 02 # IP address 10.3.137.2 |
| IPPortClassifier01_Port = 5002 # Port 5002 |
| IPPortClassifier01_DTag = 4 # User priority 4 |
| |
| IPPortClassifier02_IPAddress = 0a 03 89 02 # IP address 10.3.137.2 |
| IPPortClassifier02_Port = 5003 # Port 5003 |
| IPPortClassifier02_DTag = 6 # User priority 6 |
| |
| |
| NumOfCodePoints = 4 |
| DSCPClassifier00_CodePoint = 0 #Best Effort |
| DSCPClassifier00_DTag = 0 |
| |
| DSCPClassifier01_CodePoint = 8 #Background |
| DSCPClassifier01_DTag = 1 |
| |
| DSCPClassifier02_CodePoint = 40 #Video |
| DSCPClassifier02_DTag = 5 |
| |
| DSCPClassifier03_CodePoint = 56 #Voice |
| DSCPClassifier03_DTag = 7 |
| |
| dot11MaxReceiveLifetime=512000 |
| FracOfLifeTimeToDrop = 50 |
| |
| WiFiAdhoc = 0 |
| WiFiWmmPS = 0 # Use 1 on WiFi test in order to configure PS to work in WMM mode |
| |
| EarlyWakeUp = 1 # 0 - Disable , 1 - Enable |
| |
| TxEnergyDetection = 0 # Use 1 for enabling |
| |
| TriggeredScanTimeOut = 50000 # Maximum time in Us between 2 channels on triggered scan |
| # PsPoll delivery failure solution |
| PsPollDeliveryFailureRecoveryPeriod = 1000 # Time in Ms to stay ACTIVE ('0' to disable feature) (orig = 20) |
| ConsecutivePsPollDeliveryFailureThreshold = 15 # Number of failed PsPoll's to start ACTIVE time out (orig = 4) |
| |
| # BT Coexistence configuration |
| BThWlanCoexistEnable = 2 # 0 - SG_ENABLE |
| # 1 - SG_DISABLE (default) |
| # 2 - SG_SENSE (auto-detect activity) |
| BThWlanCoexistParamsallowPaSdToggleDuringBtActivityEnable = 0 # 0 |
| # 1 - (default) |
| BThWlanCoexistParamsnumberOWlanPackets = 2 |
| BThWlanCoexistParamsnumberOfBtPackets = 6 |
| # The timeout before falling asleep after PsPoll (default 15) |
| QOS_rxTimeoutPsPoll = 30 |
