| /* |
| * Copyright 2012 The Android Open Source Project |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| |
| #ifndef BT_VENDOR_QCOM_H |
| #define BT_VENDOR_QCOM_H |
| |
| #include <stdbool.h> |
| #include "bt_vendor_lib.h" |
| |
| #ifndef FALSE |
| #define FALSE 0 |
| #endif |
| |
| #ifndef TRUE |
| #define TRUE (!FALSE) |
| #endif |
| |
| #define STREAM_TO_UINT16(u16, p) {u16 = ((uint16_t)(*(p)) + (((uint16_t)(*((p) + 1))) << 8)); (p) += 2;} |
| #define UINT16_TO_STREAM(p, u16) {*(p)++ = (uint8_t)(u16); *(p)++ = (uint8_t)((u16) >> 8);} |
| #define UINT32_TO_STREAM(p, u32) {*(p)++ = (uint8_t)(u32); *(p)++ = (uint8_t)((u32) >> 8); *(p)++ = (uint8_t)((u32) >> 16); *(p)++ = (uint8_t)((u32) >> 24);} |
| |
| typedef enum { |
| BT_SOC_DEFAULT = 0, |
| BT_SOC_SMD = BT_SOC_DEFAULT, |
| BT_SOC_AR3K, |
| BT_SOC_ROME, |
| BT_SOC_CHEROKEE, |
| /* Add chipset type here */ |
| BT_SOC_RESERVED |
| }bt_soc_type; |
| |
| typedef enum { |
| FM_VND_OP_POWER_CTRL = (unsigned int)BT_VND_OP_A2DP_OFFLOAD_STOP + 1, |
| BT_VND_OP_FM_USERIAL_OPEN, |
| BT_VND_OP_FM_USERIAL_CLOSE, |
| }bt_fm_serial; |
| |
| typedef enum { |
| BT_VND_OP_ANT_USERIAL_OPEN = 254, |
| BT_VND_OP_ANT_USERIAL_CLOSE |
| }ant_serial; |
| |
| /* HW_NEED_END_WITH_HCI_RESET |
| |
| code implementation of sending a HCI_RESET command during the epilog |
| process. It calls back to the callers after command complete of HCI_RESET |
| is received. |
| |
| Default TRUE . |
| */ |
| #ifndef HW_NEED_END_WITH_HCI_RESET |
| #define HW_NEED_END_WITH_HCI_RESET TRUE |
| #endif |
| |
| #define HCI_RESET 0x0C03 |
| #define HCI_CMD_PREAMBLE_SIZE 3 |
| #define HCI_EVT_CMD_CMPL_STATUS_RET_BYTE 5 |
| #define HCI_EVT_CMD_CMPL_OPCODE 3 |
| #define BT_PWR_CNTRL_DEVICE "/dev/btpower" |
| |
| enum { |
| BT_STATUS_SUCCESS = 0, |
| BT_STATUS_FAIL, |
| BT_STATUS_INVAL, |
| BT_STATUS_NOMEM, |
| BT_STATUS_PROP_FAILURE, |
| }; |
| #define BT_CMD_PWR_CTRL 0xbfad |
| struct bt_qcom_struct { |
| int fd[2]; |
| int ant_fd; |
| int fm_fd; |
| bt_vendor_callbacks_t *cb; |
| uint8_t bdaddr[6]; |
| int soc_type; |
| int rfkill_id; |
| char *rfkill_state; |
| bool enable_extldo; |
| }; |
| extern struct bt_qcom_struct q; |
| |
| #endif /* BT_VENDOR_QCOM_H */ |
| |