| /* |
| * Copyright 2016 The Android Open Source Project |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| |
| package android.hardware.wifi.supplicant@1.0; |
| |
| import ISupplicantIface; |
| import ISupplicantP2pIfaceCallback; |
| |
| /** |
| * Interface exposed by the supplicant for each P2P mode network |
| * interface (e.g p2p0) it controls. |
| */ |
| interface ISupplicantP2pIface extends ISupplicantIface { |
| enum WpsProvisionMethod : uint32_t { |
| /** |
| * Push button method. |
| */ |
| PBC, |
| /** |
| * Display pin method configuration - pin is generated and displayed on |
| * device. |
| */ |
| DISPLAY, |
| /** |
| * Keypad pin method configuration - pin is entered on device. |
| */ |
| KEYPAD |
| }; |
| |
| /** |
| * Use to specify a range of frequencies. |
| * For example: 2412-2432,2462,5000-6000, etc. |
| */ |
| struct FreqRange { |
| uint32_t min; |
| uint32_t max; |
| }; |
| |
| /** |
| * Enum describing the modes of Miracast supported |
| * via driver commands. |
| */ |
| enum MiracastMode : uint8_t { |
| DISABLED = 0, |
| /** |
| * Operating as source. |
| */ |
| SOURCE = 1, |
| /** |
| * Operating as sink. |
| */ |
| SINK = 2 |
| }; |
| |
| /** |
| * Register for callbacks from this interface. |
| * |
| * These callbacks are invoked for events that are specific to this interface. |
| * Registration of multiple callback objects is supported. These objects must |
| * be automatically deleted when the corresponding client process is dead or |
| * if this interface is removed. |
| * |
| * @param callback An instance of the |ISupplicantP2pIfaceCallback| HIDL |
| * interface object. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| registerCallback(ISupplicantP2pIfaceCallback callback) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Gets the MAC address of the device. |
| * |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * @return deviceAddress MAC address of the device. |
| */ |
| getDeviceAddress() |
| generates (SupplicantStatus status, MacAddress deviceAddress); |
| |
| /** |
| * Set the postfix to be used for P2P SSID's. |
| * |
| * @param postfix String to be appended to SSID. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_ARGS_INVALID|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| setSsidPostfix(vec<uint8_t> postfix) generates (SupplicantStatus status); |
| |
| /** |
| * Set the Maximum idle time in seconds for P2P groups. |
| * This value controls how long a P2P group is maintained after there |
| * is no other members in the group. As a group owner, this means no |
| * associated stations in the group. As a P2P client, this means no |
| * group owner seen in scan results. |
| * |
| * @param groupIfName Group interface name to use. |
| * @param timeoutInSec Timeout value in seconds. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| setGroupIdle(string groupIfName, uint32_t timeoutInSec) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Turn on/off power save mode for the interface. |
| * |
| * @param groupIfName Group interface name to use. |
| * @param enable Indicate if power save is to be turned on/off. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID|, |
| * |SupplicantStatusCode.FAILURE_IFACE_DISABLED| |
| */ |
| setPowerSave(string groupIfName, bool enable) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Initiate a P2P service discovery with an optional timeout. |
| * |
| * @param timeoutInSec Max time to be spent is peforming discovery. |
| * Set to 0 to indefinely continue discovery untill and explicit |
| * |stopFind| is sent. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * |SupplicantStatusCode.FAILURE_IFACE_DISABLED| |
| */ |
| find(uint32_t timeoutInSec) generates (SupplicantStatus status); |
| |
| /** |
| * Stop an ongoing P2P service discovery. |
| * |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * |SupplicantStatusCode.FAILURE_IFACE_DISABLED| |
| */ |
| stopFind() generates (SupplicantStatus status); |
| |
| /** |
| * Flush P2P peer table and state. |
| * |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| flush() generates (SupplicantStatus status); |
| |
| /** |
| * Start P2P group formation with a discovered P2P peer. This includes |
| * optional group owner negotiation, group interface setup, provisioning, |
| * and establishing data connection. |
| * |
| * @param peerAddress MAC address of the device to connect to. |
| * @method provisionMethod Provisioning method to use. |
| * @param preSelectedPin Pin to be used, if |provisionMethod| uses one of the |
| * preselected |PIN*| methods. |
| * @param joinExistingGroup Indicates that this is a command to join an |
| * existing group as a client. It skips the group owner negotiation |
| * part. This must send a Provision Discovery Request message to the |
| * target group owner before associating for WPS provisioning. |
| * @param persistent Used to request a persistent group to be formed. |
| * @param goIntent Used to override the default Intent for this group owner |
| * negotiation (Values from 1-15). Refer to section 4.1.6 in |
| * Wi-Fi Peer-to-Peer (P2P) Technical Specification Version 1.7. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_ARGS_INVALID|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * @return generatedPin Pin generated, if |provisionMethod| uses one of the |
| * generated |PIN*| methods. |
| */ |
| connect(MacAddress peerAddress, |
| WpsProvisionMethod provisionMethod, |
| string preSelectedPin, |
| bool joinExistingGroup, |
| bool persistent, |
| uint32_t goIntent) |
| generates (SupplicantStatus status, string generatedPin); |
| |
| /** |
| * Cancel an ongoing P2P group formation and joining-a-group related |
| * operation. This operation unauthorizes the specific peer device (if any |
| * had been authorized to start group formation), stops P2P find (if in |
| * progress), stops pending operations for join-a-group, and removes the |
| * P2P group interface (if one was used) that is in the WPS provisioning |
| * step. If the WPS provisioning step has been completed, the group is not |
| * terminated. |
| * |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_NOT_STARTED|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| cancelConnect() generates (SupplicantStatus status); |
| |
| /** |
| * Send P2P provision discovery request to the specified peer. The |
| * parameters for this command are the P2P device address of the peer and the |
| * desired configuration method. |
| * |
| * @param peerAddress MAC address of the device to send discovery. |
| * @method provisionMethod Provisioning method to use. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| provisionDiscovery(MacAddress peerAddress, |
| WpsProvisionMethod provisionMethod) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Set up a P2P group owner manually (i.e., without group owner |
| * negotiation with a specific peer). This is also known as autonomous |
| * group owner. Optional |persistentNetworkId| may be used to specify |
| * restart of a persistent group. |
| * |
| * @param persistent Used to request a persistent group to be formed. |
| * @param persistentNetworkId Used to specify the restart of a persistent |
| * group. Set to UINT32_MAX for a non-persistent group. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| addGroup(bool persistent, SupplicantNetworkId persistentNetworkId) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Terminate a P2P group. If a new virtual network interface was used for |
| * the group, it must also be removed. The network interface name of the |
| * group interface is used as a parameter for this command. |
| * |
| * @param groupIfName Group interface name to use. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| removeGroup(string groupIfName) generates (SupplicantStatus status); |
| |
| /** |
| * Reject connection attempt from a peer (specified with a device |
| * address). This is a mechanism to reject a pending group owner negotiation |
| * with a peer and request to automatically block any further connection or |
| * discovery of the peer. |
| * |
| * @param peerAddress MAC address of the device to reject. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * |SupplicantStatusCode.FAILURE_IFACE_DISABLED| |
| */ |
| reject(MacAddress peerAddress) generates (SupplicantStatus status); |
| |
| /** |
| * Invite a device to a persistent group. |
| * If the peer device is the group owner of the persistent group, the peer |
| * parameter is not needed. Otherwise it is used to specify which |
| * device to invite. |goDeviceAddress| parameter may be used to override |
| * the group owner device address for Invitation Request should it not be |
| * known for some reason (this should not be needed in most cases). |
| * |
| * @param groupIfName Group interface name to use. |
| * @param goDeviceAddress MAC address of the group owner device. |
| * @param peerAddress MAC address of the device to invite. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| invite(string groupIfName, MacAddress goDeviceAddress, MacAddress peerAddress) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Reinvoke a device from a persistent group. |
| * |
| * @param persistentNetworkId Used to specify the persistent group. |
| * @param peerAddress MAC address of the device to reinvoke. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| reinvoke(SupplicantNetworkId persistentNetworkId, MacAddress peerAddress) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Configure Extended Listen Timing. |
| * |
| * If enabled, listen state must be entered every |intervalInMillis| for at |
| * least |periodInMillis|. Both values have acceptable range of 1-65535 |
| * (with interval obviously having to be larger than or equal to duration). |
| * If the P2P module is not idle at the time the Extended Listen Timing |
| * timeout occurs, the Listen State operation must be skipped. |
| * |
| * @param periodInMillis Period in milliseconds. |
| * @param intervalInMillis Interval in milliseconds. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_ARGS_INVALID|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| configureExtListen(uint32_t periodInMillis, |
| uint32_t intervalInMillis) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Set P2P Listen channel. |
| * |
| * When specifying a social channel on the 2.4 GHz band (1/6/11) there is no |
| * need to specify the operating class since it defaults to 81. When |
| * specifying a social channel on the 60 GHz band (2), specify the 60 GHz |
| * operating class (180). |
| * |
| * @param channel Wifi channel. eg, 1, 6, 11. |
| * @param operatingClass Operating Class indicates the channel set of the AP |
| * indicated by this BSSID |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| setListenChannel(uint32_t channel, uint32_t operatingClass) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Set P2P disallowed frequency ranges. |
| * |
| * Specify ranges of frequencies that are disallowed for any p2p operations. |
| |
| * @param ranges List of ranges which needs to be disallowed. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| setDisallowedFrequencies(vec<FreqRange> ranges) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Gets the operational SSID of the device. |
| * |
| * @param peerAddress MAC address of the peer. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * @return ssid SSID of the device |
| */ |
| getSsid(MacAddress peerAddress) |
| generates (SupplicantStatus status, Ssid ssid); |
| |
| /** |
| * Gets the capability of the group which the device is a |
| * member of. |
| * |
| * @param peerAddress MAC address of the peer. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * @return capabilityMask Combination of |P2pGroupCapabilityMask| values. |
| */ |
| getGroupCapability(MacAddress peerAddress) |
| generates (SupplicantStatus status, |
| bitfield<P2pGroupCapabilityMask> capabilities); |
| |
| /** |
| * This command can be used to add a bonjour service. |
| * |
| * @param query Hex dump of the query data. |
| * @param return Hex dump of the response data. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| addBonjourService(vec<uint8_t> query, vec<uint8_t> response) |
| generates (SupplicantStatus status); |
| |
| /** |
| * This command can be used to remove a bonjour service. |
| * |
| * @param query Hex dump of the query data. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_NOT_STARTED|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| removeBonjourService(vec<uint8_t> query) generates (SupplicantStatus status); |
| |
| /** |
| * This command can be used to add a UPNP service. |
| * |
| * @param version Version to be used. |
| * @package serviceName Service name to be used. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| addUpnpService(uint32_t version, string serviceName) |
| generates (SupplicantStatus status); |
| |
| /** |
| * This command can be used to remove a UPNP service. |
| * |
| * @param version Version to be used. |
| * @package serviceName Service name to be used. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_NOT_STARTED|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| removeUpnpService(uint32_t version, string serviceName) |
| generates (SupplicantStatus status); |
| |
| /** |
| * This command can be used to flush all services from the |
| * device. |
| * |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| flushServices() generates (SupplicantStatus status); |
| |
| /** |
| * Schedule a P2P service discovery request. The parameters for this command |
| * are the device address of the peer device (or 00:00:00:00:00:00 for |
| * wildcard query that is sent to every discovered P2P peer that supports |
| * service discovery) and P2P Service Query TLV(s) as hexdump. |
| * |
| * @param peerAddress MAC address of the device to discover. |
| * @param query Hex dump of the query data. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * @return identifier Identifier for the request. Can be used to cancel the |
| * request. |
| */ |
| requestServiceDiscovery(MacAddress peerAddress, vec<uint8_t> query) |
| generates (SupplicantStatus status, uint64_t identifier); |
| |
| /** |
| * Cancel a previous service discovery request. |
| * |
| * @return identifier Identifier for the request to cancel. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_NOT_STARTED|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| cancelServiceDiscovery(uint64_t identifier) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Send driver command to set Miracast mode. |
| * |
| * @param mode Mode of Miracast. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| setMiracastMode(MiracastMode mode) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Initiate WPS Push Button setup. |
| * The PBC operation requires that a button is also pressed at the |
| * AP/Registrar at about the same time (2 minute window). |
| * |
| * @param groupIfName Group interface name to use. |
| * @param bssid BSSID of the AP. Use zero'ed bssid to indicate wildcard. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| startWpsPbc(string groupIfName, Bssid bssid) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Initiate WPS Pin Keypad setup. |
| * |
| * @param groupIfName Group interface name to use. |
| * @param pin 8 digit pin to be used. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| startWpsPinKeypad(string groupIfName, string pin) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Initiate WPS Pin Display setup. |
| * |
| * @param groupIfName Group interface name to use. |
| * @param bssid BSSID of the AP. Use zero'ed bssid to indicate wildcard. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * @return generatedPin 8 digit pin generated. |
| */ |
| startWpsPinDisplay(string groupIfName, Bssid bssid) |
| generates (SupplicantStatus status, string generatedPin); |
| |
| /** |
| * Cancel any ongoing WPS operations. |
| * |
| * @param groupIfName Group interface name to use. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| |
| */ |
| cancelWps(string groupIfName) generates (SupplicantStatus status); |
| |
| /** |
| * Enable/Disable Wifi Display. |
| * |
| * @param enable true to enable, false to disable. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| enableWfd(bool enable) generates (SupplicantStatus status); |
| |
| /** |
| * Set Wifi Display device info. |
| * |
| * @param info WFD device info as described in section 5.1.2 of WFD technical |
| * specification v1.0.0. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| setWfdDeviceInfo(uint8_t[6] info) generates (SupplicantStatus status); |
| |
| /** |
| * Creates a NFC handover request message. |
| * |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * @return request Bytes representing the handover request as specified in |
| * section 3.1.1 of NFC Connection Handover 1.2 Technical |
| * Specification. |
| */ |
| createNfcHandoverRequestMessage() |
| generates (SupplicantStatus status, vec<uint8_t> request); |
| |
| /** |
| * Creates a NFC handover select message. |
| * |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| * @return select Bytes representing the handover select as specified in |
| * section 3.1.2 of NFC Connection Handover 1.2 Technical |
| * Specification. |
| */ |
| createNfcHandoverSelectMessage() |
| generates (SupplicantStatus status, vec<uint8_t> select); |
| |
| /** |
| * Report the response of the NFC handover request. |
| * |
| * @param request Bytes representing the handover request as specified in |
| * section 3.1.1 of NFC Connection Handover 1.2 Technical |
| * Specification. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| reportNfcHandoverResponse(vec<uint8_t> request) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Report the initiation of the NFC handover select. |
| * |
| * @param select Bytes representing the handover select as specified in |
| * section 3.1.2 of NFC Connection Handover 1.2 Technical |
| * Specification. |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| reportNfcHandoverInitiation(vec<uint8_t> select) |
| generates (SupplicantStatus status); |
| |
| /** |
| * Persist the current configuration to disk. |
| * |
| * @return status Status of the operation. |
| * Possible status codes: |
| * |SupplicantStatusCode.SUCCESS|, |
| * |SupplicantStatusCode.FAILURE_UNKNOWN|, |
| * |SupplicantStatusCode.FAILURE_IFACE_INVALID| |
| */ |
| saveConfig() generates (SupplicantStatus status); |
| }; |
