blob: d0cfe392ae966e9156a5bdd57005f9e1367fc70b [file] [log] [blame]
* Copyright (C) 2018 The Android Open Source Project
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* See the License for the specific language governing permissions and
* limitations under the License.
import @3.2::CameraMetadata;
import @3.4::ICameraDeviceSession;
import @3.4::HalStreamConfiguration;
* Camera device active session interface.
* Obtained via ICameraDevice::open(), this interface contains the methods to
* configure and request captures from an active camera device.
interface ICameraDeviceSession extends @3.4::ICameraDeviceSession {
* configureStreams_3_5:
* Identical to @3.4::ICameraDeviceSession.configureStreams, except that:
* - a streamConfigCounter counter is provided to check for race condition
* between configureStreams_3_5 and signalStreamFlush call.
* @return status Status code for the operation, one of:
* OK:
* On successful stream configuration.
* If there has been a fatal error and the device is no longer
* operational. Only close() can be called successfully by the
* framework after this error is returned.
* If the requested stream configuration is invalid. Some examples
* of invalid stream configurations include:
* - Including more than 1 INPUT stream
* - Not including any OUTPUT streams
* - Including streams with unsupported formats, or an unsupported
* size for that format.
* - Including too many output streams of a certain format.
* - Unsupported rotation configuration
* - Stream sizes/formats don't satisfy the
* StreamConfigurationMode requirements
* for non-NORMAL mode, or the requested operation_mode is not
* supported by the HAL.
* - Unsupported usage flag
* The camera service cannot filter out all possible illegal stream
* configurations, since some devices may support more simultaneous
* streams or larger stream resolutions than the minimum required
* for a given camera device hardware level. The HAL must return an
* ILLEGAL_ARGUMENT for any unsupported stream set, and then be
* ready to accept a future valid stream configuration in a later
* configureStreams call.
* @return halConfiguration The stream parameters desired by the HAL for
* each stream, including maximum buffers, the usage flags, and the
* override format.
configureStreams_3_5(@3.5::StreamConfiguration requestedConfiguration)
generates (Status status,
@3.4::HalStreamConfiguration halConfiguration);
* signalStreamFlush:
* Signaling HAL camera service is about to perform configureStreams_3_5 and
* HAL must return all buffers of designated streams. HAL must finish
* inflight requests normally and return all buffers that belongs to the
* designated streams through processCaptureResult or returnStreamBuffer
* API in a timely manner, or camera service will run into a fatal error.
* Note that this call serves as an optional hint and camera service may
* skip sending this call if all buffers are already returned.
* @param streamIds The ID of streams camera service need all of its
* buffers returned.
* @param streamConfigCounter Note that due to concurrency nature, it is
* possible the signalStreamFlush call arrives later than the
* corresponding configureStreams_3_5 call, HAL must check
* streamConfigCounter for such race condition. If the counter is less
* than the counter in the last configureStreams_3_5 call HAL last
* received, the call is stale and HAL should just return this call.
oneway signalStreamFlush(
vec<int32_t> streamIds,
uint32_t streamConfigCounter
* isReconfigurationRequired:
* Check whether complete stream reconfiguration is required for possible new session
* parameter values.
* This method must be called by the camera framework in case the client changes
* the value of any advertised session parameters. Depending on the specific values
* the HAL can decide whether a complete stream reconfiguration is required. In case
* the HAL returns false, the camera framework must skip the internal reconfiguration.
* In case Hal returns true, the framework must reconfigure the streams and pass the
* new session parameter values accordingly.
* This call may be done by the framework some time before the request with new parameters
* is submitted to the HAL, and the request may be cancelled before it ever gets submitted.
* Therefore, the HAL must not use this query as an indication to change its behavior in any
* way.
* ------------------------------------------------------------------------
* Preconditions:
* The framework can call this method at any time after active
* session configuration. There must be no impact on the performance of
* pending camera requests in any way. In particular there must not be
* any glitches or delays during normal camera streaming.
* Performance requirements:
* HW and SW camera settings must not be changed and there must not be
* a user-visible impact on camera performance.
* @param oldSessionParams Before session parameters, usually the current session parameters.
* @param newSessionParams The new session parameters which may be set by client.
* @return Status Status code for the operation, one of:
* OK:
* On successful reconfiguration required query.
* The camera device does not support the reconfiguration query.
* The reconfiguration query cannot complete due to internal
* error.
* @return true in case the stream reconfiguration is required, false otherwise.
isReconfigurationRequired(CameraMetadata oldSessionParams, CameraMetadata newSessionParams)
generates(Status status, bool reconfigurationNeeded);