Camera: Handle abandoned surface in finishConfiguration
It's possible that surface for a stream goes away after
cameraservice configures HAL stream, either during configure_streams
or when session parameters are updated.
In this case, do not put camera device in an error state.
Test: Camera CTS, GCA
Bug: 111581884
Change-Id: I7efc5aa22bc9b60ffaea23d8dae275f9a2bd026d
diff --git a/services/camera/libcameraservice/device3/Camera3Device.cpp b/services/camera/libcameraservice/device3/Camera3Device.cpp
index 543914e..28ffc8b 100644
--- a/services/camera/libcameraservice/device3/Camera3Device.cpp
+++ b/services/camera/libcameraservice/device3/Camera3Device.cpp
@@ -2143,8 +2143,14 @@
res = stream->finishConfiguration();
if (res != OK) {
- SET_ERR_L("Can't finish configuring output stream %d: %s (%d)",
- stream->getId(), strerror(-res), res);
+ // If finishConfiguration fails due to abandoned surface, do not set
+ // device to error state.
+ bool isSurfaceAbandoned =
+ (res == NO_INIT || res == DEAD_OBJECT) && stream->isAbandoned();
+ if (!isSurfaceAbandoned) {
+ SET_ERR_L("Can't finish configuring output stream %d: %s (%d)",
+ stream->getId(), strerror(-res), res);
+ }
return res;
}
}
@@ -2361,9 +2367,16 @@
//present streams end up with outstanding buffers that will
//not get drained.
internalUpdateStatusLocked(STATUS_ACTIVE);
+ } else if (rc == DEAD_OBJECT) {
+ // DEAD_OBJECT can be returned if either the consumer surface is
+ // abandoned, or the HAL has died.
+ // - If the HAL has died, configureStreamsLocked call will set
+ // device to error state,
+ // - If surface is abandoned, we should not set device to error
+ // state.
+ ALOGE("Failed to re-configure camera due to abandoned surface");
} else {
- setErrorStateLocked("%s: Failed to re-configure camera: %d",
- __FUNCTION__, rc);
+ SET_ERR_L("Failed to re-configure camera: %d", rc);
}
} else {
ALOGE("%s: Failed to pause streaming: %d", __FUNCTION__, rc);
@@ -2497,6 +2510,9 @@
CLOGE("Can't finish configuring input stream %d: %s (%d)",
mInputStream->getId(), strerror(-res), res);
cancelStreamsConfigurationLocked();
+ if ((res == NO_INIT || res == DEAD_OBJECT) && mInputStream->isAbandoned()) {
+ return DEAD_OBJECT;
+ }
return BAD_VALUE;
}
}
@@ -2510,6 +2526,9 @@
CLOGE("Can't finish configuring output stream %d: %s (%d)",
outputStream->getId(), strerror(-res), res);
cancelStreamsConfigurationLocked();
+ if ((res == NO_INIT || res == DEAD_OBJECT) && outputStream->isAbandoned()) {
+ return DEAD_OBJECT;
+ }
return BAD_VALUE;
}
}
diff --git a/services/camera/libcameraservice/device3/Camera3Stream.cpp b/services/camera/libcameraservice/device3/Camera3Stream.cpp
index 1105b75..6030d15 100644
--- a/services/camera/libcameraservice/device3/Camera3Stream.cpp
+++ b/services/camera/libcameraservice/device3/Camera3Stream.cpp
@@ -331,7 +331,14 @@
status_t res;
res = configureQueueLocked();
- if (res != OK) {
+ // configureQueueLocked could return error in case of abandoned surface.
+ // Treat as non-fatal error.
+ if (res == NO_INIT || res == DEAD_OBJECT) {
+ ALOGE("%s: Unable to configure stream %d queue (non-fatal): %s (%d)",
+ __FUNCTION__, mId, strerror(-res), res);
+ mState = STATE_ABANDONED;
+ return res;
+ } else if (res != OK) {
ALOGE("%s: Unable to configure stream %d queue: %s (%d)",
__FUNCTION__, mId, strerror(-res), res);
mState = STATE_ERROR;
diff --git a/services/camera/libcameraservice/device3/Camera3Stream.h b/services/camera/libcameraservice/device3/Camera3Stream.h
index a60cb56..4ddcf1a 100644
--- a/services/camera/libcameraservice/device3/Camera3Stream.h
+++ b/services/camera/libcameraservice/device3/Camera3Stream.h
@@ -482,6 +482,7 @@
// after the HAL has provided usage and max_buffers values. After this call,
// the stream must be ready to produce all buffers for registration with
// HAL.
+ // Returns NO_INIT or DEAD_OBJECT if the queue has been abandoned.
virtual status_t configureQueueLocked() = 0;
// Get the total number of buffers in the queue
