blob: 496da17b39f3515acde65e086312d332813eee4c [file] [log] [blame]
/*
* (C) Copyright 2011 Logic Product Development <www.logicpd.com>
* Peter Barada <peter.barada@logicpd.com>
*
* Configuration settings for the Logic OMAP35x/DM37x SOM LV/Torpedo
* reference boards.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/* High Level Configuration Options */
#define CONFIG_NR_DRAM_BANKS 2 /* CS1 may or may not be populated */
/*
* 1MB into the SDRAM to allow for SPL's bss at the beginning of SDRAM
* 64 bytes before this address should be set aside for u-boot.img's
* header. That is 0x800FFFC0--0x80100000 should not be used for any
* other needs. We use this rather than the inherited defines from
* ti_armv7_common.h for backwards compatibility.
*/
#define CONFIG_SYS_TEXT_BASE 0x80100000
#define CONFIG_SPL_BSS_START_ADDR 0x80000000
#define CONFIG_SPL_BSS_MAX_SIZE (512 << 10) /* 512 KB */
#define CONFIG_SYS_SPL_MALLOC_START 0x80208000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x100000
#include <configs/ti_omap3_common.h>
/*
* We are only ever GP parts and will utilize all of the "downloaded image"
* area in SRAM which starts at 0x40200000 and ends at 0x4020FFFF (64KB) in
* order to allow for BCH8 to fit in.
*/
#undef CONFIG_SPL_TEXT_BASE
#define CONFIG_SPL_TEXT_BASE 0x40200000
/* Display CPU and Board information */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_MISC_INIT_R /* misc_init_r dumps the die id */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_CMDLINE_EDITING /* cmd line edit/history */
/* Hardware drivers */
/* GPIO banks */
#define CONFIG_OMAP3_GPIO_6 /* GPIO160..191 is in GPIO bank 6 */
#define CONFIG_USB_OMAP3
/* select serial console configuration */
#undef CONFIG_CONS_INDEX
#define CONFIG_CONS_INDEX 1
#define CONFIG_SYS_NS16550_COM1 OMAP34XX_UART1
#define CONFIG_SERIAL1 1 /* UART1 on OMAP Logic boards */
/* commands to include */
#define CONFIG_CMD_NAND
#define CONFIG_CMD_MTDPARTS
#define CONFIG_CMD_NAND_LOCK_UNLOCK /* nand (un)lock commands */
/* I2C */
#define CONFIG_SYS_I2C_OMAP34XX
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM AT24C64 */
#define EXPANSION_EEPROM_I2C_BUS 2 /* I2C Bus for AT24C64 */
#define CONFIG_OMAP3_LOGIC_USE_NEW_PRODUCT_ID
/* USB */
#define CONFIG_USB_MUSB_OMAP2PLUS
#define CONFIG_USB_MUSB_PIO_ONLY
#define CONFIG_USB_ETHER
#define CONFIG_USB_ETHER_RNDIS
#define CONFIG_USB_FUNCTION_FASTBOOT
#define CONFIG_CMD_FASTBOOT
#define CONFIG_ANDROID_BOOT_IMAGE
#define CONFIG_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR
#define CONFIG_FASTBOOT_BUF_SIZE 0x07000000
/* TWL4030 */
#define CONFIG_TWL4030_PWM
#define CONFIG_TWL4030_USB
/* Board NAND Info. */
#ifdef CONFIG_NAND
#define CONFIG_NAND_OMAP_GPMC
#define CONFIG_CMD_UBI /* UBI-formated MTD partition support */
#define CONFIG_CMD_UBIFS /* Read-only UBI volume operations */
#define CONFIG_RBTREE /* required by CONFIG_CMD_UBI */
#define CONFIG_LZO /* required by CONFIG_CMD_UBIFS */
#define CONFIG_SYS_NAND_ADDR NAND_BASE /* physical address */
/* to access nand */
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of */
/* NAND devices */
#define CONFIG_SYS_NAND_BUSWIDTH_16BIT
#define CONFIG_SYS_NAND_5_ADDR_CYCLE
#define CONFIG_SYS_NAND_PAGE_COUNT 64
#define CONFIG_SYS_NAND_PAGE_SIZE 2048
#define CONFIG_SYS_NAND_OOBSIZE 64
#define CONFIG_SYS_NAND_BLOCK_SIZE (128 * 1024)
#define CONFIG_SYS_NAND_BAD_BLOCK_POS NAND_LARGE_BADBLOCK_POS
#define CONFIG_SYS_NAND_ECCPOS {2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, \
13, 14, 16, 17, 18, 19, 20, 21, 22, \
23, 24, 25, 26, 27, 28, 30, 31, 32, \
33, 34, 35, 36, 37, 38, 39, 40, 41, \
42, 44, 45, 46, 47, 48, 49, 50, 51, \
52, 53, 54, 55, 56}
#define CONFIG_SYS_NAND_ECCSIZE 512
#define CONFIG_SYS_NAND_ECCBYTES 13
#define CONFIG_NAND_OMAP_ECCSCHEME OMAP_ECC_BCH8_CODE_HW_DETECTION_SW
#define CONFIG_BCH
#define CONFIG_SYS_NAND_MAX_OOBFREE 2
#define CONFIG_SYS_NAND_MAX_ECCPOS 56
#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x80000
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_MTD_PARTITIONS /* required for UBI partition support */
#define MTDIDS_DEFAULT "nand0=omap2-nand.0"
#define MTDPARTS_DEFAULT "mtdparts=omap2-nand.0:512k(MLO),"\
"1920k(u-boot),128k(u-boot-env),"\
"4m(kernel),-(fs)"
#endif
/* Environment information */
/*
* PREBOOT assumes the 4.3" display is attached. User can interrupt
* and modify display variable to suit their needs.
*/
#define CONFIG_PREBOOT \
"echo ======================NOTICE============================;"\
"echo \"The u-boot environment is not set.\";" \
"echo \"If using a display a valid display variable for your panel\";" \
"echo \"needs to be set.\";" \
"echo \"Valid display options are:\";" \
"echo \" 2 == LQ121S1DG31 TFT SVGA (12.1) Sharp\";" \
"echo \" 3 == LQ036Q1DA01 TFT QVGA (3.6) Sharp w/ASIC\";" \
"echo \" 5 == LQ064D343 TFT VGA (6.4) Sharp\";" \
"echo \" 7 == LQ10D368 TFT VGA (10.4) Sharp\";" \
"echo \" 15 == LQ043T1DG01 TFT WQVGA (4.3) Sharp (DEFAULT)\";" \
"echo \" vga[-dvi or -hdmi] LCD VGA 640x480\";" \
"echo \" svga[-dvi or -hdmi] LCD SVGA 800x600\";" \
"echo \" xga[-dvi or -hdmi] LCD XGA 1024x768\";" \
"echo \" 720p[-dvi or -hdmi] LCD 720P 1280x720\";" \
"echo \"Defaulting to 4.3 LCD panel (display=15).\";" \
"setenv display 15;" \
"setenv preboot;" \
"nand unlock;" \
"saveenv;"
#define CONFIG_EXTRA_ENV_SETTINGS \
"loadaddr=0x81000000\0" \
"uimage=uImage\0" \
"zimage=zImage\0" \
"mtdids=" MTDIDS_DEFAULT "\0" \
"mtdparts=" MTDPARTS_DEFAULT "\0" \
"mmcdev=0\0" \
"mmcroot=/dev/mmcblk0p2 rw\0" \
"mmcrootfstype=ext4 rootwait\0" \
"nandroot=ubi0:rootfs rw ubi.mtd=fs noinitrd\0" \
"nandrootfstype=ubifs rootwait\0" \
"autoboot=mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"run defaultboot;" \
"fi; " \
"else run defaultboot; fi\0" \
"defaultboot=run mmcramboot\0" \
"consoledevice=ttyO0\0" \
"display=15\0" \
"setconsole=setenv console ${consoledevice},${baudrate}n8\0" \
"dump_bootargs=echo 'Bootargs: '; echo $bootargs\0" \
"rotation=0\0" \
"vrfb_arg=if itest ${rotation} -ne 0; then " \
"setenv bootargs ${bootargs} omapfb.vrfb=y " \
"omapfb.rotate=${rotation}; " \
"fi\0" \
"optargs=ignore_loglevel early_printk no_console_suspend\0" \
"addmtdparts=setenv bootargs ${bootargs} ${mtdparts}\0" \
"common_bootargs=setenv bootargs ${bootargs} display=${display} " \
"${optargs};" \
"run addmtdparts; " \
"run vrfb_arg\0" \
"loadbootscript=fatload mmc ${mmcdev} ${loadaddr} boot.scr\0" \
"bootscript=echo 'Running bootscript from mmc ...'; " \
"source ${loadaddr}\0" \
"loaduimage=mmc rescan; " \
"fatload mmc ${mmcdev} ${loadaddr} ${uimage}\0" \
"loadzimage=mmc rescan; " \
"fatload mmc ${mmcdev} ${loadaddr} ${zimage}\0" \
"ramdisksize=64000\0" \
"ramdiskaddr=0x82000000\0" \
"ramdiskimage=rootfs.ext2.gz.uboot\0" \
"loadramdisk=mmc rescan; " \
"fatload mmc ${mmcdev} ${ramdiskaddr} ${ramdiskimage}\0" \
"ramargs=run setconsole; setenv bootargs console=${console} " \
"root=/dev/ram rw ramdisk_size=${ramdisksize}\0" \
"mmcargs=run setconsole; setenv bootargs console=${console} " \
"${optargs} " \
"root=${mmcroot} " \
"rootfstype=${mmcrootfstype}\0" \
"nandargs=run setconsole; setenv bootargs console=${console} " \
"${optargs} " \
"root=${nandroot} " \
"rootfstype=${nandrootfstype}\0" \
"fdtaddr=0x86000000\0" \
"loadfdtimage=mmc rescan; " \
"fatload mmc ${mmcdev} ${fdtaddr} ${fdtimage}\0" \
"mmcbootz=echo Booting with DT from mmc${mmcdev} ...; " \
"run mmcargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"run loadzimage; " \
"run loadfdtimage; " \
"bootz ${loadaddr} - ${fdtaddr}\0" \
"mmcramboot=echo 'Booting uImage kernel from mmc w/ramdisk...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"run loaduimage; " \
"run loadramdisk; " \
"bootm ${loadaddr} ${ramdiskaddr}\0" \
"mmcrambootz=echo 'Booting zImage kernel from mmc w/ramdisk...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"run loadzimage; " \
"run loadramdisk; " \
"run loadfdtimage; " \
"bootz ${loadaddr} ${ramdiskaddr} ${fdtaddr}\0; " \
"tftpboot=echo 'Booting kernel/ramdisk rootfs from tftp...'; " \
"run ramargs; " \
"run common_bootargs; " \
"run dump_bootargs; " \
"tftpboot ${loadaddr} ${uimage}; " \
"tftpboot ${ramdiskaddr} ${ramdiskimage}; " \
"bootm ${loadaddr} ${ramdiskaddr}\0"
#define CONFIG_BOOTCOMMAND \
"run autoboot"
/* Miscellaneous configurable options */
#define CONFIG_AUTO_COMPLETE
/* memtest works on */
#define CONFIG_SYS_MEMTEST_START (OMAP34XX_SDRC_CS0)
#define CONFIG_SYS_MEMTEST_END (OMAP34XX_SDRC_CS0 + \
0x01F00000) /* 31MB */
/* FLASH and environment organization */
/* **** PISMO SUPPORT *** */
#if defined(CONFIG_CMD_NAND)
#define CONFIG_SYS_FLASH_BASE NAND_BASE
#elif defined(CONFIG_CMD_ONENAND)
#define CONFIG_SYS_FLASH_BASE ONENAND_MAP
#endif
/* Monitor at start of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_SIZE (128 << 10) /* 128 KiB */
#define ONENAND_ENV_OFFSET 0x260000 /* environment starts here */
#define SMNAND_ENV_OFFSET 0x260000 /* environment starts here */
#define CONFIG_SYS_ENV_SECT_SIZE (128 << 10) /* 128 KiB */
#define CONFIG_ENV_OFFSET SMNAND_ENV_OFFSET
#define CONFIG_ENV_ADDR SMNAND_ENV_OFFSET
/* SMSC922x Ethernet */
#if defined(CONFIG_CMD_NET)
#define CONFIG_SMC911X
#define CONFIG_SMC911X_32_BIT
#define CONFIG_SMC911X_BASE 0x08000000
#endif /* (CONFIG_CMD_NET) */
/* Defines for SPL */
#define CONFIG_SPL_OMAP3_ID_NAND
/* NAND: SPL falcon mode configs */
#ifdef CONFIG_SPL_OS_BOOT
#define CONFIG_CMD_SPL_NAND_OFS 0x240000
#define CONFIG_SYS_NAND_SPL_KERNEL_OFFS 0x280000
#define CONFIG_CMD_SPL_WRITE_SIZE 0x2000
#endif
#endif /* __CONFIG_H */