blob: 8301c4670fb41b296a64657f5699940f8f6170de [file] [log] [blame]
/*
* Configuation settings for the Freescale MCF54455 EVB board.
*
* Copyright (C) 2004-2007 Freescale Semiconductor, Inc.
* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef _M54455EVB_H
#define _M54455EVB_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_M54455EVB /* M54455EVB board */
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (0)
#define CONFIG_BAUDRATE 115200
#undef CONFIG_WATCHDOG
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/* Command line configuration */
#define CONFIG_CMD_DATE
#define CONFIG_CMD_IDE
#define CONFIG_CMD_JFFS2
#undef CONFIG_CMD_PCI
#define CONFIG_CMD_REGINFO
/* Network configuration */
#define CONFIG_MCFFEC
#ifdef CONFIG_MCFFEC
# define CONFIG_MII 1
# define CONFIG_MII_INIT 1
# define CONFIG_SYS_DISCOVER_PHY
# define CONFIG_SYS_RX_ETH_BUFFER 8
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_SYS_FEC0_PINMUX 0
# define CONFIG_SYS_FEC1_PINMUX 0
# define CONFIG_SYS_FEC0_MIIBASE CONFIG_SYS_FEC0_IOBASE
# define CONFIG_SYS_FEC1_MIIBASE CONFIG_SYS_FEC0_IOBASE
# define MCFFEC_TOUT_LOOP 50000
# define CONFIG_HAS_ETH1
# define CONFIG_BOOTARGS "root=/dev/mtdblock1 rw rootfstype=jffs2 ip=none mtdparts=physmap-flash.0:5M(kernel)ro,-(jffs2)"
# define CONFIG_ETHPRIME "FEC0"
# define CONFIG_IPADDR 192.162.1.2
# define CONFIG_NETMASK 255.255.255.0
# define CONFIG_SERVERIP 192.162.1.1
# define CONFIG_GATEWAYIP 192.162.1.1
/* If CONFIG_SYS_DISCOVER_PHY is not defined - hardcoded */
# ifndef CONFIG_SYS_DISCOVER_PHY
# define FECDUPLEX FULL
# define FECSPEED _100BASET
# else
# ifndef CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# define CONFIG_SYS_FAULT_ECHO_LINK_DOWN
# endif
# endif /* CONFIG_SYS_DISCOVER_PHY */
#endif
#define CONFIG_HOSTNAME M54455EVB
#ifdef CONFIG_SYS_STMICRO_BOOT
/* ST Micro serial flash */
#define CONFIG_SYS_LOAD_ADDR2 0x40010013
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
"loadaddr=0x40010000\0" \
"sbfhdr=sbfhdr.bin\0" \
"uboot=u-boot.bin\0" \
"load=tftp ${loadaddr} ${sbfhdr};" \
"tftp " __stringify(CONFIG_SYS_LOAD_ADDR2) " ${uboot} \0" \
"upd=run load; run prog\0" \
"prog=sf probe 0:1 1000000 3;" \
"sf erase 0 30000;" \
"sf write ${loadaddr} 0 0x30000;" \
"save\0" \
""
#else
/* Atmel and Intel */
#ifdef CONFIG_SYS_ATMEL_BOOT
# define CONFIG_SYS_UBOOT_END 0x0403FFFF
#elif defined(CONFIG_SYS_INTEL_BOOT)
# define CONFIG_SYS_UBOOT_END 0x3FFFF
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"inpclk=" __stringify(CONFIG_SYS_INPUT_CLKSRC) "\0" \
"loadaddr=0x40010000\0" \
"uboot=u-boot.bin\0" \
"load=tftp ${loadaddr} ${uboot}\0" \
"upd=run load; run prog\0" \
"prog=prot off " __stringify(CONFIG_SYS_FLASH_BASE) \
" " __stringify(CONFIG_SYS_UBOOT_END) ";" \
"era " __stringify(CONFIG_SYS_FLASH_BASE) " " \
__stringify(CONFIG_SYS_UBOOT_END) ";" \
"cp.b ${loadaddr} " __stringify(CONFIG_SYS_FLASH_BASE) \
" ${filesize}; save\0" \
""
#endif
/* ATA configuration */
#define CONFIG_ISO_PARTITION
#define CONFIG_DOS_PARTITION
#define CONFIG_IDE_RESET 1
#define CONFIG_IDE_PREINIT 1
#define CONFIG_ATAPI
#undef CONFIG_LBA48
#define CONFIG_SYS_IDE_MAXBUS 1
#define CONFIG_SYS_IDE_MAXDEVICE 2
#define CONFIG_SYS_ATA_BASE_ADDR 0x90000000
#define CONFIG_SYS_ATA_IDE0_OFFSET 0
#define CONFIG_SYS_ATA_DATA_OFFSET 0xA0 /* Offset for data I/O */
#define CONFIG_SYS_ATA_REG_OFFSET 0xA0 /* Offset for normal register accesses */
#define CONFIG_SYS_ATA_ALT_OFFSET 0xC0 /* Offset for alternate registers */
#define CONFIG_SYS_ATA_STRIDE 4 /* Interval between registers */
/* Realtime clock */
#define CONFIG_MCFRTC
#undef RTC_DEBUG
#define CONFIG_SYS_RTC_OSCILLATOR (32 * CONFIG_SYS_HZ)
/* Timer */
#define CONFIG_MCFTMR
#undef CONFIG_MCFPIT
/* I2c */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 80000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/* DSPI and Serial Flash */
#define CONFIG_CF_SPI
#define CONFIG_CF_DSPI
#define CONFIG_HARD_SPI
#define CONFIG_SYS_SBFHDR_SIZE 0x13
#ifdef CONFIG_CMD_SPI
# define CONFIG_SYS_DSPI_CTAR0 (DSPI_CTAR_TRSZ(7) | \
DSPI_CTAR_PCSSCK_1CLK | \
DSPI_CTAR_PASC(0) | \
DSPI_CTAR_PDT(0) | \
DSPI_CTAR_CSSCK(0) | \
DSPI_CTAR_ASC(0) | \
DSPI_CTAR_DT(1))
#endif
/* PCI */
#ifdef CONFIG_CMD_PCI
#define CONFIG_PCI 1
#define CONFIG_PCI_PNP 1
#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1
#define CONFIG_SYS_PCI_CACHE_LINE_SIZE 4
#define CONFIG_SYS_PCI_MEM_BUS 0xA0000000
#define CONFIG_SYS_PCI_MEM_PHYS CONFIG_SYS_PCI_MEM_BUS
#define CONFIG_SYS_PCI_MEM_SIZE 0x10000000
#define CONFIG_SYS_PCI_IO_BUS 0xB1000000
#define CONFIG_SYS_PCI_IO_PHYS CONFIG_SYS_PCI_IO_BUS
#define CONFIG_SYS_PCI_IO_SIZE 0x01000000
#define CONFIG_SYS_PCI_CFG_BUS 0xB0000000
#define CONFIG_SYS_PCI_CFG_PHYS CONFIG_SYS_PCI_CFG_BUS
#define CONFIG_SYS_PCI_CFG_SIZE 0x01000000
#endif
/* FPGA - Spartan 2 */
/* experiment
#define CONFIG_FPGA
#define CONFIG_FPGA_COUNT 1
#define CONFIG_SYS_FPGA_PROG_FEEDBACK
#define CONFIG_SYS_FPGA_CHECK_CTRLC
*/
/* Input, PCI, Flexbus, and VCO */
#define CONFIG_EXTRA_CLOCK
#define CONFIG_PRAM 2048 /* 2048 KB */
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_SDRAM_BASE + 0x10000)
#define CONFIG_SYS_MBAR 0xFC000000
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in DPRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x8000 /* Size of used area in internal SRAM */
#define CONFIG_SYS_INIT_RAM_CTRL 0x221
#define CONFIG_SYS_GBL_DATA_OFFSET ((CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE) - 32)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_SBFHDR_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - 32)
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define CONFIG_SYS_SDRAM_BASE1 0x48000000
#define CONFIG_SYS_SDRAM_SIZE 256 /* SDRAM size in MB */
#define CONFIG_SYS_SDRAM_CFG1 0x65311610
#define CONFIG_SYS_SDRAM_CFG2 0x59670000
#define CONFIG_SYS_SDRAM_CTRL 0xEA0B2000
#define CONFIG_SYS_SDRAM_EMOD 0x40010000
#define CONFIG_SYS_SDRAM_MODE 0x00010033
#define CONFIG_SYS_SDRAM_DRV_STRENGTH 0xAA
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE + 0x400
#define CONFIG_SYS_MEMTEST_END ((CONFIG_SYS_SDRAM_SIZE - 3) << 20)
#ifdef CONFIG_CF_SBF
# define CONFIG_SERIAL_BOOT
# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_TEXT_BASE + 0x400)
#else
# define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
#endif
#define CONFIG_SYS_BOOTPARAMS_LEN 64*1024
#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
/* Reserve 256 kB for malloc() */
#define CONFIG_SYS_MALLOC_LEN (256 << 10)
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
/* Initial Memory map for Linux */
#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + (CONFIG_SYS_SDRAM_SIZE << 20))
/*
* Configuration for environment
* Environment is not embedded in u-boot. First time runing may have env
* crc error warning if there is no correct environment on the flash.
*/
#ifdef CONFIG_CF_SBF
# define CONFIG_ENV_IS_IN_SPI_FLASH
# define CONFIG_ENV_SPI_CS 1
#else
# define CONFIG_ENV_IS_IN_FLASH 1
#endif
#undef CONFIG_ENV_OVERWRITE
/*-----------------------------------------------------------------------
* FLASH organization
*/
#ifdef CONFIG_SYS_STMICRO_BOOT
# define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
# define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS1_BASE
# define CONFIG_ENV_OFFSET 0x30000
# define CONFIG_ENV_SIZE 0x2000
# define CONFIG_ENV_SECT_SIZE 0x10000
#endif
#ifdef CONFIG_SYS_ATMEL_BOOT
# define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
# define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS0_BASE
# define CONFIG_SYS_FLASH1_BASE CONFIG_SYS_CS1_BASE
# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)
# define CONFIG_ENV_SIZE 0x2000
# define CONFIG_ENV_SECT_SIZE 0x10000
#endif
#ifdef CONFIG_SYS_INTEL_BOOT
# define CONFIG_SYS_FLASH_BASE CONFIG_SYS_CS0_BASE
# define CONFIG_SYS_FLASH0_BASE CONFIG_SYS_CS0_BASE
# define CONFIG_SYS_FLASH1_BASE CONFIG_SYS_CS1_BASE
# define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x40000)
# define CONFIG_ENV_SIZE 0x2000
# define CONFIG_ENV_SECT_SIZE 0x20000
#endif
#define CONFIG_SYS_FLASH_CFI
#ifdef CONFIG_SYS_FLASH_CFI
# define CONFIG_FLASH_CFI_DRIVER 1
# define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
# define CONFIG_SYS_FLASH_SIZE 0x1000000 /* Max size that the board might have */
# define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
# define CONFIG_SYS_MAX_FLASH_BANKS 2 /* max number of memory banks */
# define CONFIG_SYS_MAX_FLASH_SECT 137 /* max number of sectors on one chip */
# define CONFIG_SYS_FLASH_PROTECTION /* "Real" (hardware) sectors protection */
# define CONFIG_SYS_FLASH_CHECKSUM
# define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_CS0_BASE, CONFIG_SYS_CS1_BASE }
# define CONFIG_FLASH_CFI_LEGACY
#ifdef CONFIG_FLASH_CFI_LEGACY
# define CONFIG_SYS_ATMEL_REGION 4
# define CONFIG_SYS_ATMEL_TOTALSECT 11
# define CONFIG_SYS_ATMEL_SECT {1, 2, 1, 7}
# define CONFIG_SYS_ATMEL_SECTSZ {0x4000, 0x2000, 0x8000, 0x10000}
#endif
#endif
/*
* This is setting for JFFS2 support in u-boot.
* NOTE: Enable CONFIG_CMD_JFFS2 for JFFS2 support.
*/
#ifdef CONFIG_CMD_JFFS2
#ifdef CF_STMICRO_BOOT
# define CONFIG_JFFS2_DEV "nor1"
# define CONFIG_JFFS2_PART_SIZE 0x01000000
# define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH2_BASE + 0x500000)
#endif
#ifdef CONFIG_SYS_ATMEL_BOOT
# define CONFIG_JFFS2_DEV "nor1"
# define CONFIG_JFFS2_PART_SIZE 0x01000000
# define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH1_BASE + 0x500000)
#endif
#ifdef CONFIG_SYS_INTEL_BOOT
# define CONFIG_JFFS2_DEV "nor0"
# define CONFIG_JFFS2_PART_SIZE (0x01000000 - 0x500000)
# define CONFIG_JFFS2_PART_OFFSET (CONFIG_SYS_FLASH0_BASE + 0x500000)
#endif
#endif
/*-----------------------------------------------------------------------
* Cache Configuration
*/
#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV (CF_CACR_BCINVA + CF_CACR_ICINVA)
#define CONFIG_SYS_DCACHE_INV (CF_CACR_DCINVA)
#define CONFIG_SYS_CACHE_ACR2 (CONFIG_SYS_SDRAM_BASE | \
CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR (CF_CACR_BEC | CF_CACR_IEC | \
CF_CACR_ICINVA | CF_CACR_EUSP)
#define CONFIG_SYS_CACHE_DCACR ((CONFIG_SYS_CACHE_ICACR | \
CF_CACR_DEC | CF_CACR_DDCM_P | \
CF_CACR_DCINVA) & ~CF_CACR_ICINVA)
/*-----------------------------------------------------------------------
* Memory bank definitions
*/
/*
* CS0 - NOR Flash 1, 2, 4, or 8MB
* CS1 - CompactFlash and registers
* CS2 - CPLD
* CS3 - FPGA
* CS4 - Available
* CS5 - Available
*/
#if defined(CONFIG_SYS_ATMEL_BOOT) || defined(CONFIG_SYS_STMICRO_BOOT)
/* Atmel Flash */
#define CONFIG_SYS_CS0_BASE 0x04000000
#define CONFIG_SYS_CS0_MASK 0x00070001
#define CONFIG_SYS_CS0_CTRL 0x00001140
/* Intel Flash */
#define CONFIG_SYS_CS1_BASE 0x00000000
#define CONFIG_SYS_CS1_MASK 0x01FF0001
#define CONFIG_SYS_CS1_CTRL 0x00000D60
#define CONFIG_SYS_ATMEL_BASE CONFIG_SYS_CS0_BASE
#else
/* Intel Flash */
#define CONFIG_SYS_CS0_BASE 0x00000000
#define CONFIG_SYS_CS0_MASK 0x01FF0001
#define CONFIG_SYS_CS0_CTRL 0x00000D60
/* Atmel Flash */
#define CONFIG_SYS_CS1_BASE 0x04000000
#define CONFIG_SYS_CS1_MASK 0x00070001
#define CONFIG_SYS_CS1_CTRL 0x00001140
#define CONFIG_SYS_ATMEL_BASE CONFIG_SYS_CS1_BASE
#endif
/* CPLD */
#define CONFIG_SYS_CS2_BASE 0x08000000
#define CONFIG_SYS_CS2_MASK 0x00070001
#define CONFIG_SYS_CS2_CTRL 0x003f1140
/* FPGA */
#define CONFIG_SYS_CS3_BASE 0x09000000
#define CONFIG_SYS_CS3_MASK 0x00070001
#define CONFIG_SYS_CS3_CTRL 0x00000020
#endif /* _M54455EVB_H */