blob: 73cdc5b489fb4b070065d109c0da2c25a7e9a786 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright (C) 2015 Timesys Corporation
* Copyright (C) 2015 General Electric Company
* Copyright (C) 2014 Advantech
* Copyright (C) 2012 Freescale Semiconductor, Inc.
*
* Configuration settings for the GE MX6Q Bx50v3 boards.
*/
#ifndef __GE_BX50V3_CONFIG_H
#define __GE_BX50V3_CONFIG_H
#include <asm/arch/imx-regs.h>
#include <asm/mach-imx/gpio.h>
#define CONFIG_BOARD_NAME "General Electric Bx50v3"
#define CONFIG_MXC_UART_BASE UART3_BASE
#define CONSOLE_DEV "ttymxc2"
#include "mx6_common.h"
#include <linux/sizes.h>
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_SYS_MALLOC_LEN (10 * SZ_1M)
#define CONFIG_MXC_UART
/* SATA Configs */
#ifdef CONFIG_CMD_SATA
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_DWC_AHSATA_PORT_ID 0
#define CONFIG_DWC_AHSATA_BASE_ADDR SATA_ARB_BASE_ADDR
#define CONFIG_LBA48
#endif
/* USB Configs */
#ifdef CONFIG_USB
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
#define CONFIG_USBD_HS
#define CONFIG_USB_GADGET_MASS_STORAGE
#endif
/* Networking Configs */
#ifdef CONFIG_NET
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 4
#define CONFIG_PHY_ATHEROS
#endif
/* Serial Flash */
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_LOADADDR 0x12000000
#ifdef CONFIG_NFS_CMD
#define NETWORKBOOT \
"setnetworkboot=" \
"setenv ipaddr 172.16.2.10; setenv serverip 172.16.2.20; " \
"setenv gatewayip 172.16.2.20; setenv nfsserver 172.16.2.20; " \
"setenv netmask 255.255.255.0; setenv ethaddr ca:fe:de:ca:f0:11; " \
"setenv bootargs root=/dev/nfs nfsroot=${nfsserver}:/srv/nfs/,v3,tcp rw rootwait" \
"setenv bootargs $bootargs ip=${ipaddr}:${nfsserver}:${gatewayip}:${netmask}::eth0:off " \
"setenv bootargs $bootargs cma=128M bootcause=POR console=${console} ${videoargs} " \
"setenv bootargs $bootargs systemd.mask=helix-network-defaults.service " \
"setenv bootargs $bootargs watchdog.handle_boot_enabled=1\0" \
"networkboot=" \
"run setnetworkboot; " \
"nfs ${loadaddr} /srv/nfs/fitImage; " \
"bootm ${loadaddr}#conf@${confidx}\0" \
#define CONFIG_NETWORKBOOTCOMMAND \
"run networkboot; " \
#else
#define NETWORKBOOT \
#endif
#define CONFIG_EXTRA_ENV_SETTINGS \
NETWORKBOOT \
"bootcause=POR\0" \
"image=/boot/fitImage\0" \
"fdt_high=0xffffffff\0" \
"dev=mmc\0" \
"devnum=2\0" \
"rootdev=mmcblk0p\0" \
"quiet=quiet loglevel=0\0" \
"console=" CONSOLE_DEV "\0" \
"setargs=setenv bootargs root=/dev/${rootdev}${partnum} " \
"ro rootwait cma=128M " \
"bootcause=${bootcause} " \
"${quiet} console=${console} ${rtc_status} " \
"${videoargs}" "\0" \
"doquiet=" \
"if ext2load ${dev} ${devnum}:5 0x7000A000 /boot/console; " \
"then setenv quiet; fi\0" \
"hasfirstboot=" \
"ext2load ${dev} ${devnum}:${partnum} 0x7000A000 " \
"/boot/bootcause/firstboot\0" \
"swappartitions=" \
"setexpr partnum 3 - ${partnum}\0" \
"failbootcmd=" \
"bx50_backlight_enable; " \
"msg=\"Monitor failed to start. Try again, or contact GE Service for support.\"; " \
"echo $msg; " \
"setenv stdout vga; " \
"echo \"\n\n\n\n \" $msg; " \
"setenv stdout serial; " \
"mw.b 0x7000A000 0xbc; " \
"mw.b 0x7000A001 0x00; " \
"ext4write ${dev} ${devnum}:5 0x7000A000 /boot/failures 2\0" \
"altbootcmd=" \
"run doquiet; " \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run hasfirstboot || setenv partnum 0; " \
"if test ${partnum} != 0; then " \
"setenv bootcause REVERT; " \
"run swappartitions loadimage doboot; " \
"fi; " \
"run failbootcmd\0" \
"loadimage=" \
"ext2load ${dev} ${devnum}:${partnum} ${loadaddr} ${image}\0" \
"doboot=" \
"echo Booting from ${dev}:${devnum}:${partnum} ...; " \
"run setargs; " \
"bootm ${loadaddr}#conf@${confidx}\0" \
"tryboot=" \
"setenv partnum 1; run hasfirstboot || setenv partnum 2; " \
"run loadimage || run swappartitions && run loadimage || " \
"setenv partnum 0 && echo MISSING IMAGE;" \
"run doboot; " \
"run failbootcmd\0" \
#define CONFIG_MMCBOOTCOMMAND \
"if mmc dev ${devnum}; then " \
"run doquiet; " \
"run tryboot; " \
"fi; " \
#define CONFIG_USBBOOTCOMMAND \
"echo Unsupported; " \
#ifdef CONFIG_NFS_CMD
#define CONFIG_BOOTCOMMAND CONFIG_NETWORKBOOTCOMMAND
#elif CONFIG_CMD_USB
#define CONFIG_BOOTCOMMAND CONFIG_USBBOOTCOMMAND
#else
#define CONFIG_BOOTCOMMAND CONFIG_MMCBOOTCOMMAND
#endif
/* Miscellaneous configurable options */
#define CONFIG_SYS_MEMTEST_START 0x10000000
#define CONFIG_SYS_MEMTEST_END 0x10010000
#define CONFIG_SYS_MEMTEST_SCRATCH 0x10800000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
/* Physical Memory Map */
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* environment organization */
#define CONFIG_SYS_FSL_USDHC_NUM 3
/* Framebuffer */
#define CONFIG_HIDE_LOGO_VERSION
#define CONFIG_IMX_HDMI
#define CONFIG_IMX_VIDEO_SKIP
#define CONFIG_CMD_BMP
#define CONFIG_IMX6_PWM_PER_CLK 66000000
#define CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_PCIE_IMX
#define CONFIG_PCIE_IMX_PERST_GPIO IMX_GPIO_NR(7, 12)
#define CONFIG_PCIE_IMX_POWER_GPIO IMX_GPIO_NR(1, 5)
#define CONFIG_RTC_RX8010SJ
#define CONFIG_SYS_RTC_BUS_NUM 2
#define CONFIG_SYS_I2C_RTC_ADDR 0x32
/* I2C Configs */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_SYS_I2C_SPEED 100000
#define CONFIG_SYS_I2C_MXC_I2C1
#define CONFIG_SYS_I2C_MXC_I2C2
#define CONFIG_SYS_I2C_MXC_I2C3
#define CONFIG_SYS_NUM_I2C_BUSES 11
#define CONFIG_SYS_I2C_MAX_HOPS 1
#define CONFIG_SYS_I2C_BUSES { {0, {I2C_NULL_HOP} }, \
{1, {I2C_NULL_HOP} }, \
{2, {I2C_NULL_HOP} }, \
{0, {{I2C_MUX_PCA9547, 0x70, 0} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 1} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 2} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 3} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 4} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 5} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 6} } }, \
{0, {{I2C_MUX_PCA9547, 0x70, 7} } }, \
}
#define CONFIG_BCH
#endif /* __GE_BX50V3_CONFIG_H */