| Command coverage |
| ================ |
| The following table lists SCSI commands in alphabetical order on the |
| left and the sg3_utils utilities that implement invocations of them |
| on the right. The second table lists supported ATA commands. |
| |
| SCSI command sg3_utils utilities that use this SCSI command |
| ------------ ------------------------------------------------- |
| ATA COMMAND PASS-THROUGH(16) sg_sat_identify, sg_sat_set_features, |
| sg_sat_phy_event, ++ |
| [sg_sat_chk_power, sg__sat_identify, |
| sg__sat_set_features, sg_sat_smart_rd_data |
| (previous four in the examples directory)] |
| ATA COMMAND PASS-THROUGH(12) sg_sat_identify, ++ |
| GET CONFIGURATION sg_get_config, ++ |
| GET LBA STATUS sg_get_lba_status, ++ |
| INQUIRY sg_dd, sg_format, sg_inq, sginfo, |
| sg_logs, sg_map('-i'), sg_modes, sg_opcodes, |
| sg_persist, sg_scan, sg_ses, sg_vpd ++ |
| FORMAT UNIT sg_format, ++ |
| LOG SELECT sg_logs('-r' or '-select'), ++ |
| LOG SENSE sg_logs, ++ |
| MODE SELECT(6) sg_wr_mode, sginfo, sg_format, |
| sg_emc_trespass, sg_rdac, ++ |
| MODE SELECT(10) sg_wr_mode, sginfo, sg_format, |
| sg_emc_trespass, sg_rdac, ++ |
| MODE SENSE(6) sg_modes, sg_wr_mode, sginfo, sg_format, |
| sg_senddiag('-e'), sg_rdac, ++ |
| MODE SENSE(10) sg_modes, sg_wr_mode, sginfo, sg_format, |
| sg_senddiag('-e'), sg_rdac, ++ |
| PERSISTENT RESERVE IN sg_persist, ++ |
| PERSISTENT RESERVE OUT sg_persist, ++ |
| PREVENT ALLOW MEDIUM REMOVAL sg_prevent, ++ |
| READ(6) sg_dd, sgm_dd, sgp_dd, sg_read |
| READ(10) sg_dd, sgm_dd, sgp_dd, sg_read |
| READ(12) sg_dd, sgm_dd, sgp_dd, sg_read |
| READ(16) sg_dd, sgm_dd, sgp_dd, sg_read |
| READ BLOCK LIMITS sg_read_block_limits, ++ |
| READ BUFFER sg_rbuf, sg_test_rwbuf, sg_read_buffer, sg_safte, ++ |
| READ CAPACITY(10) sg_readcap, sg_dd, sgm_dd, sgp_dd, sg_format, ++ |
| READ CAPACITY(16) sg_readcap, sg_dd, sgm_dd, sgp_dd, sg_format, ++ |
| READ DEFECT(10) sginfo, sg_reassign('-g'), ++ |
| READ DEFECT(12) sginfo |
| READ LONG (10) sg_read_long, sg_dd, ++ |
| READ LONG (16) sg_read_long, ++ |
| READ MEDIA SERIAL NUMBER sg_rmsn, ++ |
| REASSIGN BLOCKS sg_reassign, ++ |
| RECEIVE DIAGNOSTIC sg_senddiag, sg_ses, ++ |
| REPORT IDENTIFYING INFORMATION sg_ident, ++ (2) |
| REPORT LUNS sg_luns, ++ |
| REPORT SUPPORTED OPERATION CODES sg_opcodes |
| REPORT SUPPORTED TASK MANAGEMENT FUNCTIONS sg_opcodes |
| REPORT TARGET PORT GROUPS sg_rtpg, sg_stpg ++ |
| REQUEST SENSE sg_requests, ++ |
| SEND DIAGNOSTIC sg_senddiag, sg_ses, ++ |
| SET IDENTIFYING INFORMATION sg_ident, ++ (3) |
| SET TARGET PORT GROUPS sg_stpg, ++ |
| START STOP sg_start, ++ |
| SYNCHRONIZE CACHE(10) sg_sync, sg_dd, sgm_dd, sgp_dd, ++ |
| TEST UNIT READY sg_turs, sg_format, ++ |
| UNMAP sg_unmap, ++ |
| VERIFY(10) sg_verify, ++ |
| WRITE(6) sg_dd, sgm_dd, sgp_dd |
| WRITE(10) sg_dd, sgm_dd, sgp_dd |
| WRITE(12) sg_dd, sgm_dd, sgp_dd |
| WRITE(16) sg_dd, sgm_dd, sgp_dd |
| WRITE BUFFER sg_test_rwbuf, sg_write_buffer, ++ |
| WRITE LONG(10) sg_write_long, ++ |
| WRITE LONG(16) sg_write_long, ++ |
| WRITE SAME(10) sg_write_same |
| WRITE SAME(16) sg_write_same |
| WRITE SAME(32) sg_write_same |
| <most commands> sg_raw |
| |
| |
| |
| ATA command sg3_utils utilities that use this SCSI command |
| ----------- ---------------------------------------------- |
| CHECK POWER MODE examples/sg_sat_chk_power |
| IDENTIFY DEVICE sg_inq, sg_scan, sg_sat_identify, |
| examples/sg__sat_identify |
| IDENTIFY PACKET DEVICE sg_inq, sg_sat_identify, |
| examples/sg__sat_identify |
| READ LOG EXT sg_sat_phy_event, examples/sg__sat_phy_event |
| SET FEATURES sg_sat_set_features |
| examples/sg__sat_set_features |
| SMART READ DATA examples/sg_sat_smart_rd_data |
| |
| |
| ++ command wrapper found in sg_cmds_basic.c, sg_cmds_mmc.c or |
| sg_cmds_extra.c for this command |
| (2) this command was known as REPORT DEVICE IDENTIFIER prior to spc4r07 |
| (3) this command was known as SET DEVICE IDENTIFIER prior to spc4r07 |
| |
| |
| Doug Gilbert |
| 20th September 2009 |
