halimpl/bcm2079x/libnfc-brcm.conf - platform/external/libnfc-nci - Git at Google

 ## this file is used by Broadcom's Hardware Abstraction Layer at external/libnfc-nci/halimpl/

 ###############################################################################
 # Application options
 APPL_TRACE_LEVEL=0xFF
 PROTOCOL_TRACE_LEVEL=0xFFFFFFFF

 ###############################################################################
 # performance measurement
 # Change this setting to control how often USERIAL log the performance (throughput)
 # data on read/write/poll
 # defailt is to log performance dara for every 100 read or write
 #REPORT_PERFORMANCE_MEASURE=100

 ###############################################################################
 # File used for NFA storage
 NFA_STORAGE="/data/nfc"

 ###############################################################################
 # Snooze Mode Settings
 #
 #  By default snooze mode is enabled.  Set SNOOZE_MODE_CFG byte[0] to 0
 #  to disable.
 #
 #  If SNOOZE_MODE_CFG is not provided, the default settings are used:
 #  They are as follows:
 #       8             Sleep Mode (0=Disabled 1=UART 8=SPI/I2C)
 #       0             Idle Threshold Host
 #       0             Idle Threshold HC
 #       0             NFC Wake active mode (0=ActiveLow 1=ActiveHigh)
 #       1             Host Wake active mode (0=ActiveLow 1=ActiveHigh)
 #
 #SNOOZE_MODE_CFG={08:00:00:00:01}

 ###############################################################################
 # Insert a delay in milliseconds after NFC_WAKE and before write to NFCC
 NFC_WAKE_DELAY=20

 ###############################################################################
 # Various Delay settings (in ms) used in USERIAL
 #  POWER_ON_DELAY
 #    Delay after turning on chip, before writing to transport (default 300)
 #  PRE_POWER_OFF_DELAY
 #    Delay after deasserting NFC-Wake before turn off chip (default 0)
 #  POST_POWER_OFF_DELAY
 #    Delay after turning off chip, before USERIAL_close returns (default 0)
 #
 #POWER_ON_DELAY=300
 #PRE_POWER_OFF_DELAY=0
 #POST_POWER_OFF_DELAY=0

 ###############################################################################
 # LPTD mode configuration
 #  byte[0] is the length of the remaining bytes in this value
 #     if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled).
 #  byte[1] is the param id it should be set to B9.
 #  byte[2] is the length of the LPTD parameters
 #  byte[3] indicates if LPTD is enabled
 #     if set to 0, LPTD will be disabled (parameters will still be sent).
 #  byte[4-n] are the LPTD parameters.
 #  By default, LPTD is enabled and default settings are used.
 #  See nfc_hal_dm_cfg.c for defaults
 LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00}

 ###############################################################################
 # Startup Configuration (100 bytes maximum)
 #
 # For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is
 #    for UICC1.  The values are defined as:
 #   0 : UICCx only supports ISO_DEP in low power mode.
 #   2 : UICCx only supports Mifare in low power mode.
 #   3 : UICCx supports both ISO_DEP and Mifare in low power mode.
 #
 #                                                                          AA BB
 NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:28:01:01}

 ###############################################################################
 # Startup Vendor Specific Configuration (100 bytes maximum);
 #  byte[0] TLV total len = 0x5
 #  byte[1] NCI_MTS_CMD|NCI_GID_PROP = 0x2f
 #  byte[2] NCI_MSG_FRAME_LOG = 0x9
 #  byte[3] 2
 #  byte[4] 0=turn off RF frame logging; 1=turn on
 #  byte[5] 0=turn off SWP frame logging; 1=turn on
 #  NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01}

 ###############################################################################
 # Configure crystal frequency when internal LPO can't detect the frequency.
 #XTAL_FREQUENCY=0

 ###############################################################################
 # Firmware patch file
 #  If the value is not set then patch download is disabled.
 FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd"

 ###############################################################################
 # Firmware pre-patch file (sent before the above patch file)
 #  If the value is not set then pre-patch is not used.
 FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd"

 ###############################################################################
 # Firmware patch format
 #   1 = HCD
 #   2 = NCD (default)
 #NFA_CONFIG_FORMAT=2

 ###############################################################################
 # SPD Debug mode
 #  If set to 1, any failure of downloading a patch will trigger a hard-stop
 #SPD_DEBUG=0

 ###############################################################################
 # SPD Max Retry Count
 #  The number of attempts to download a patch before giving up (defualt is 3).
 #  Note, this resets after a power-cycle.
 #SPD_MAX_RETRY_COUNT=3

 ###############################################################################
 # transport driver
 #
 # TRANSPORT_DRIVER=<driver>
 #
 #  where <driver> can be, for example:
 #    "/dev/ttyS"        (UART)
 #    "/dev/bcmi2cnfc"   (I2C)
 #    "hwtun"            (HW Tunnel)
 #    "/dev/bcmspinfc"   (SPI)
 #    "/dev/btusb0"      (BT USB)
 TRANSPORT_DRIVER="/dev/bcm2079x"

 ###############################################################################
 # power control driver
 # Specify a kernel driver that support ioctl commands to control NFC_EN and
 # NFC_WAKE gpio signals.
 #
 # POWER_CONTRL_DRIVER=<driver>
 #  where <driver> can be, for example:
 #    "/dev/nfcpower"
 #    "/dev/bcmi2cnfc"   (I2C)
 #    "/dev/bcmspinfc"   (SPI)
 #    i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal
 POWER_CONTROL_DRIVER="/dev/bcm2079x"

 ###############################################################################
 # I2C transport driver options
 #
 BCMI2CNFC_ADDRESS=0

 ###############################################################################
 # I2C transport driver try to read multiple packets in read() if data is available
 # remove the comment below to enable this feature
 #READ_MULTIPLE_PACKETS=1

 ###############################################################################
 # SPI transport driver options
 #SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00}

 ###############################################################################
 # UART transport driver options
 #
 # PORT=1,2,3,...
 # BAUD=115200, 19200, 9600, 4800,
 # DATABITS=8, 7, 6, 5
 # PARITY="even" | "odd" | "none"
 # STOPBITS="0" | "1" | "1.5" | "2"

 #UART_PORT=2
 #UART_BAUD=115200
 #UART_DATABITS=8
 #UART_PARITY="none"
 #UART_STOPBITS="1"

 ###############################################################################
 # Insert a delay in microseconds per byte after a write to NFCC.
 # after writing a block of data to the NFCC, delay this an amopunt of time before
 # writing next block of data.  the delay is calculated as below
 #   NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds
 # e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write
 NFC_WRITE_DELAY=20

 ###############################################################################
 # Maximum Number of Credits to be allowed by the NFCC
 #   This value overrides what the NFCC specifices allowing the host to have
 #   the control to work-around transport limitations.  If this value does
 #   not exist or is set to 0, the NFCC will provide the number of credits.
 MAX_RF_DATA_CREDITS=1

 ###############################################################################
 # Allow UICC to be powered off if there is no traffic.
 # Timeout is in ms. If set to 0, then UICC will not be powered off.
 UICC_IDLE_TIMEOUT=30000


 ###############################################################################
 # Antenna Configuration - This data is used when setting 0xC8 config item
 # at startup (before discovery is started).  If not used, no value is sent.
 #
 # The settings for this value are documented here:
 # http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
 #   Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
 # This document is maintained by Paul Forshaw.
 #
 # The values marked as ?? should be tweaked per antenna or customer/app:
 # {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
 # array[0] = 0x20 is length of the payload from array[1] to the end
 # array[1] = 0xC8 is PREINIT_DSP_CFG
 #PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}
	## this file is used by Broadcom's Hardware Abstraction Layer at external/libnfc-nci/halimpl/

	###############################################################################
	# Application options
	APPL_TRACE_LEVEL=0xFF
	PROTOCOL_TRACE_LEVEL=0xFFFFFFFF

	###############################################################################
	# performance measurement
	# Change this setting to control how often USERIAL log the performance (throughput)
	# data on read/write/poll
	# defailt is to log performance dara for every 100 read or write
	#REPORT_PERFORMANCE_MEASURE=100

	###############################################################################
	# File used for NFA storage
	NFA_STORAGE="/data/nfc"

	###############################################################################
	# Snooze Mode Settings
	#
	# By default snooze mode is enabled. Set SNOOZE_MODE_CFG byte[0] to 0
	# to disable.
	#
	# If SNOOZE_MODE_CFG is not provided, the default settings are used:
	# They are as follows:
	# 8 Sleep Mode (0=Disabled 1=UART 8=SPI/I2C)
	# 0 Idle Threshold Host
	# 0 Idle Threshold HC
	# 0 NFC Wake active mode (0=ActiveLow 1=ActiveHigh)
	# 1 Host Wake active mode (0=ActiveLow 1=ActiveHigh)
	#
	#SNOOZE_MODE_CFG={08:00:00:00:01}

	###############################################################################
	# Insert a delay in milliseconds after NFC_WAKE and before write to NFCC
	NFC_WAKE_DELAY=20

	###############################################################################
	# Various Delay settings (in ms) used in USERIAL
	# POWER_ON_DELAY
	# Delay after turning on chip, before writing to transport (default 300)
	# PRE_POWER_OFF_DELAY
	# Delay after deasserting NFC-Wake before turn off chip (default 0)
	# POST_POWER_OFF_DELAY
	# Delay after turning off chip, before USERIAL_close returns (default 0)
	#
	#POWER_ON_DELAY=300
	#PRE_POWER_OFF_DELAY=0
	#POST_POWER_OFF_DELAY=0

	###############################################################################
	# LPTD mode configuration
	# byte[0] is the length of the remaining bytes in this value
	# if set to 0, LPTD params will NOT be sent to NFCC (i.e. disabled).
	# byte[1] is the param id it should be set to B9.
	# byte[2] is the length of the LPTD parameters
	# byte[3] indicates if LPTD is enabled
	# if set to 0, LPTD will be disabled (parameters will still be sent).
	# byte[4-n] are the LPTD parameters.
	# By default, LPTD is enabled and default settings are used.
	# See nfc_hal_dm_cfg.c for defaults
	LPTD_CFG={23:B9:21:01:02:FF:FF:04:A0:0F:40:00:80:02:02:10:00:00:00:31:0C:30:00:00:00:00:00:00:00:00:00:00:00:00:00:00}

	###############################################################################
	# Startup Configuration (100 bytes maximum)
	#
	# For the 0xCA parameter, byte[9] (marked by 'AA') is for UICC0, and byte[10] (marked by BB) is
	# for UICC1. The values are defined as:
	# 0 : UICCx only supports ISO_DEP in low power mode.
	# 2 : UICCx only supports Mifare in low power mode.
	# 3 : UICCx supports both ISO_DEP and Mifare in low power mode.
	#
	# AA BB
	NFA_DM_START_UP_CFG={1F:CB:01:01:A5:01:01:CA:14:00:00:00:00:06:E8:03:00:00:00:00:00:00:00:00:00:00:00:00:00:28:01:01}

	###############################################################################
	# Startup Vendor Specific Configuration (100 bytes maximum);
	# byte[0] TLV total len = 0x5
	# byte[1] NCI_MTS_CMD\|NCI_GID_PROP = 0x2f
	# byte[2] NCI_MSG_FRAME_LOG = 0x9
	# byte[3] 2
	# byte[4] 0=turn off RF frame logging; 1=turn on
	# byte[5] 0=turn off SWP frame logging; 1=turn on
	# NFA_DM_START_UP_VSC_CFG={05:2F:09:02:01:01}

	###############################################################################
	# Configure crystal frequency when internal LPO can't detect the frequency.
	#XTAL_FREQUENCY=0

	###############################################################################
	# Firmware patch file
	# If the value is not set then patch download is disabled.
	FW_PATCH="/vendor/firmware/bcm2079x_firmware.ncd"

	###############################################################################
	# Firmware pre-patch file (sent before the above patch file)
	# If the value is not set then pre-patch is not used.
	FW_PRE_PATCH="/vendor/firmware/bcm2079x_pre_firmware.ncd"

	###############################################################################
	# Firmware patch format
	# 1 = HCD
	# 2 = NCD (default)
	#NFA_CONFIG_FORMAT=2

	###############################################################################
	# SPD Debug mode
	# If set to 1, any failure of downloading a patch will trigger a hard-stop
	#SPD_DEBUG=0

	###############################################################################
	# SPD Max Retry Count
	# The number of attempts to download a patch before giving up (defualt is 3).
	# Note, this resets after a power-cycle.
	#SPD_MAX_RETRY_COUNT=3

	###############################################################################
	# transport driver
	#
	# TRANSPORT_DRIVER=<driver>
	#
	# where <driver> can be, for example:
	# "/dev/ttyS" (UART)
	# "/dev/bcmi2cnfc" (I2C)
	# "hwtun" (HW Tunnel)
	# "/dev/bcmspinfc" (SPI)
	# "/dev/btusb0" (BT USB)
	TRANSPORT_DRIVER="/dev/bcm2079x"

	###############################################################################
	# power control driver
	# Specify a kernel driver that support ioctl commands to control NFC_EN and
	# NFC_WAKE gpio signals.
	#
	# POWER_CONTRL_DRIVER=<driver>
	# where <driver> can be, for example:
	# "/dev/nfcpower"
	# "/dev/bcmi2cnfc" (I2C)
	# "/dev/bcmspinfc" (SPI)
	# i2c and spi driver may be used to control NFC_EN and NFC_WAKE signal
	POWER_CONTROL_DRIVER="/dev/bcm2079x"

	###############################################################################
	# I2C transport driver options
	#
	BCMI2CNFC_ADDRESS=0

	###############################################################################
	# I2C transport driver try to read multiple packets in read() if data is available
	# remove the comment below to enable this feature
	#READ_MULTIPLE_PACKETS=1

	###############################################################################
	# SPI transport driver options
	#SPI_NEGOTIATION={0A:F0:00:01:00:00:00:FF:FF:00:00}

	###############################################################################
	# UART transport driver options
	#
	# PORT=1,2,3,...
	# BAUD=115200, 19200, 9600, 4800,
	# DATABITS=8, 7, 6, 5
	# PARITY="even" \| "odd" \| "none"
	# STOPBITS="0" \| "1" \| "1.5" \| "2"

	#UART_PORT=2
	#UART_BAUD=115200
	#UART_DATABITS=8
	#UART_PARITY="none"
	#UART_STOPBITS="1"

	###############################################################################
	# Insert a delay in microseconds per byte after a write to NFCC.
	# after writing a block of data to the NFCC, delay this an amopunt of time before
	# writing next block of data. the delay is calculated as below
	# NFC_WRITE_DELAY * (number of byte written) / 1000 milliseconds
	# e.g. after 259 bytes is written, delay (259 * 20 / 1000) 5 ms before next write
	NFC_WRITE_DELAY=20

	###############################################################################
	# Maximum Number of Credits to be allowed by the NFCC
	# This value overrides what the NFCC specifices allowing the host to have
	# the control to work-around transport limitations. If this value does
	# not exist or is set to 0, the NFCC will provide the number of credits.
	MAX_RF_DATA_CREDITS=1

	###############################################################################
	# Allow UICC to be powered off if there is no traffic.
	# Timeout is in ms. If set to 0, then UICC will not be powered off.
	UICC_IDLE_TIMEOUT=30000


	###############################################################################
	# Antenna Configuration - This data is used when setting 0xC8 config item
	# at startup (before discovery is started). If not used, no value is sent.
	#
	# The settings for this value are documented here:
	# http://wcgbu.broadcom.com/wpan/PM/Project%20Document%20Library/bcm20791B0/
	# Design/Doc/PHY%20register%20settings/BCM20791-B2-1027-02_PHY_Recommended_Reg_Settings.xlsx
	# This document is maintained by Paul Forshaw.
	#
	# The values marked as ?? should be tweaked per antenna or customer/app:
	# {20:C8:1E:06:??:00:??:??:??:00:??:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:??:01:00:00:40:04}
	# array[0] = 0x20 is length of the payload from array[1] to the end
	# array[1] = 0xC8 is PREINIT_DSP_CFG
	#PREINIT_DSP_CFG={20:C8:1E:06:1F:00:0F:03:3C:00:04:24:00:1C:00:75:00:77:00:76:00:1C:00:03:00:0A:00:48:01:00:00:40:04}