| /* Copyright (c) 2012-2013, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| /include/ "msm9625-display.dtsi" |
| /include/ "qpic-panel-ili-qvga.dtsi" |
| |
| &soc { |
| i2c@f9925000 { |
| charger@57 { |
| compatible = "summit,smb137c"; |
| reg = <0x57>; |
| summit,chg-current-ma = <1500>; |
| summit,term-current-ma = <50>; |
| summit,pre-chg-current-ma = <100>; |
| summit,float-voltage-mv = <4200>; |
| summit,thresh-voltage-mv = <3000>; |
| summit,recharge-thresh-mv = <75>; |
| summit,system-voltage-mv = <4250>; |
| summit,charging-timeout = <382>; |
| summit,pre-charge-timeout = <48>; |
| summit,therm-current-ua = <10>; |
| summit,temperature-min = <4>; /* 0 C */ |
| summit,temperature-max = <3>; /* 45 C */ |
| }; |
| }; |
| |
| wlan0: qca,wlan { |
| cell-index = <0>; |
| compatible = "qca,ar6004-hsic"; |
| qca,chip-pwd-l-gpios = <&msmgpio 62 0>; |
| qca,pm-enable-gpios = <&pm8019_gpios 3 0x0>; |
| qca,vdd-io-supply = <&pm8019_l11>; |
| }; |
| |
| qca,wlan_ar6003 { |
| cell-index = <0>; |
| compatible = "qca,ar6003-sdio"; |
| qca,chip-pwd-l-gpios = <&msmgpio 62 0>; |
| qca,pm-enable-gpios = <&pm8019_gpios 3 0x0>; |
| qca,vdd-io-supply = <&pm8019_l11>; |
| }; |
| }; |
| |
| /* PM8019 GPIO and MPP configuration */ |
| &pm8019_gpios { |
| gpio@c000 { /* GPIO 1 */ |
| }; |
| |
| gpio@c100 { /* GPIO 2 */ |
| }; |
| |
| gpio@c200 { /* GPIO 3 */ |
| }; |
| |
| gpio@c300 { /* GPIO 4 */ |
| /* ext_2p95v regulator enable config */ |
| qcom,mode = <1>; /* Digital output */ |
| qcom,output-type = <0>; /* CMOS */ |
| qcom,invert = <0>; /* Output low */ |
| qcom,out-strength = <1>; /* Low */ |
| qcom,vin-sel = <2>; /* PM8019 L11 - 1.8V */ |
| qcom,src-sel = <0>; /* Constant */ |
| qcom,master-en = <1>; /* Enable GPIO */ |
| }; |
| |
| gpio@c400 { /* GPIO 5 */ |
| }; |
| |
| gpio@c500 { /* GPIO 6 */ |
| }; |
| }; |
| |
| &pm8019_mpps { |
| mpp@a000 { /* MPP 1 */ |
| }; |
| |
| mpp@a100 { /* MPP 2 */ |
| }; |
| |
| mpp@a200 { /* MPP 3 */ |
| }; |
| |
| mpp@a300 { /* MPP 4 */ |
| }; |
| |
| mpp@a400 { /* MPP 5 */ |
| }; |
| |
| mpp@a500 { /* MPP 6 */ |
| }; |
| }; |
