| /* Copyright (c) 2012, Code Aurora Forum. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| /include/ "../msm8974-leds.dtsi" |
| |
| /include/ "msm8974-lge-panel.dtsi" |
| /include/ "msm8974-lge-input.dtsi" |
| /include/ "msm8974-lge-hdmi.dtsi" |
| /include/ "msm8974-lge-usb.dtsi" |
| /include/ "msm8974-lge-misc.dtsi" |
| /include/ "msm8974-lge-pm.dtsi" |
| |
| &soc { |
| serial@f991d000 { |
| compatible = "qcom,msm-lsuart-v14"; |
| reg = <0xf991d000 0x1000>; |
| interrupts = <0 107 0>; |
| status = "disabled"; |
| |
| qcom,msm-bus,name = "serial_uart1"; |
| qcom,msm-bus,num-cases = <2>; |
| qcom,msm-bus,active-only = <0>; |
| qcom,msm-bus,num-paths = <1>; |
| qcom,msm-bus,vectors-KBps = |
| <86 512 0 0>, |
| <86 512 500 800>; |
| }; |
| |
| uart10: uart@f9960000 { /*BLSP2, UART10 For Bluetooth*/ |
| compatible = "qcom,msm-hsuart-v14"; |
| status = "disabled"; |
| reg = <0xf9960000 0x1000>, |
| <0xf9944000 0x19000>; |
| reg-names = "core_mem", "bam_mem"; |
| interrupts = <0 116 0>, <0 239 0>; |
| interrupt-names = "core_irq", "bam_irq"; |
| |
| qcom,tx-gpio = <&msmgpio 53 0x00>; |
| qcom,rx-gpio = <&msmgpio 54 0x00>; |
| qcom,cts-gpio = <&msmgpio 55 0x00>; |
| qcom,rfr-gpio = <&msmgpio 56 0x00>; |
| |
| qcom,bam-tx-ep-pipe-index = <6>; |
| qcom,bam-rx-ep-pipe-index = <7>; |
| |
| qcom,msm-bus,name = "uart10"; |
| qcom,msm-bus,num-cases = <2>; |
| qcom,msm-bus,active-only = <0>; |
| qcom,msm-bus,num-paths = <1>; |
| qcom,msm-bus,vectors-KBps = |
| <84 512 0 0>, |
| <84 512 500 800>; |
| }; |
| }; |
| |
| &spmi_bus { |
| qcom,pm8941@0 { |
| qcom,power-on@800 { |
| qcom,pon_2 { |
| qcom,disable = <1>; |
| }; |
| }; |
| }; |
| }; |
| |
| &i2c_0 { |
| qcom,active-only; |
| }; |
| |
| &i2c_1 { |
| qcom,active-only; |
| status = "ok"; |
| }; |
| |
| &i2c_2 { |
| qcom,active-only; |
| }; |