| Qualcomm I2C controller |
| |
| Required properties: |
| |
| - reg : Offset and length of the register region(s) for the device |
| For GSBI based controller, GSBI and QUP regions are expected |
| For BLSP based controller, QUP region offset is expected |
| - reg-names : Register region name(s) referenced in reg above |
| BLSP based controller expects QUP region name ("qup_phys_addr") |
| GSBI controller expects QUP region name and GSBI region name |
| ("gsbi_qup_i2c_addr") |
| - compatible : should be "qcom,i2c-qup" |
| - cell-index : I2C bus number used for this controller |
| - interrupts : QUP core interrupt(s). Core may have 1 error interrupt and flags |
| for input/output service, or 3 separate interrupts for the 3 services |
| - interrupt-names: QUP core interrupt name(s) referenced in interrupts above |
| Expected interrupt resource name(s) are: "qup_err_irq", "qup_in_irq", |
| and "qup_out_irq" |
| - qcom,i2c-bus-freq : desired I2C bus clock frequency is Hz |
| |
| Optional property: |
| - qcom,noise-rjct-scl : Number of low samples on clock line to consider it low. |
| Range of values is 0-3. When missing default to 0. |
| - qcom,noise-rjct-sda : Number of low samples on data line to consider it low. |
| Range of values is 0-3. When missing default to 0. |
| - qcom,i2c-src-freq : Frequency of the source clocking this bus in Hz. |
| Divider value is set based on soruce-frequency and |
| desired I2C bus frequency. If this value is not |
| provided, the source clock is assumed to be running |
| at 19.2 MHz. |
| - qcom,scl-gpio : I2C clock GPIO number. Required for execution of bus |
| recovery procedure. |
| - qcom,sda-gpio : I2C data GPIO number. Required for execution of bus |
| recovery procedure. |
| - qcom,active-only : Vote for core clock when the application processor goes |
| to active state and remove that vote when it goes to idle |
| state. This flag may improve service time of first i2c |
| request at the expense of power consumption. When this |
| entry is not present, voting is done by the runtime-pm |
| callbacks. |
| - qcom,master-id : Master endpoint number used for voting on clocks using |
| bus-scaling driver. |
| - qcom,clk-ctl-xfer : When present, the clocks's state (prepare_enable/ |
| unprepare_disable) is controlled by i2c-transaction's |
| begining and ending. When missing, the clock's state |
| is controlled by runtime-pm events. |
| |
| Example: |
| i2c_3: i2c@f9966000 { |
| cell-index = <3>; |
| compatible = "qcom,i2c-qup"; |
| reg = <0xf9966000 0x1000>; |
| reg-names = "qup_phys_addr"; |
| interrupts = <0 104 0>; |
| qcom,noise-rjct-scl = <1>; |
| qcom,noise-rjct-sda = <1>; |
| interrupt-names = "qup_err_intr"; |
| qcom,i2c-bus-freq = <100000>; |
| qcom,i2c-src-freq = <24000000>; |
| qcom,clk-ctl-xfer; |
| qcom,scl-gpio = <&msmgpio 7 0>; |
| qcom,sda-gpio = <&msmgpio 6 0>; |
| }; |
