ARM: dts: b1c1: Configure camera sensor imx179
[Authored by FIH]
[cfries: refactor pinctrl change from qcom dtsi into google dtsi]
Change-Id: If499c76bc4ade1a3158384b77303e4a5fa687294
Signed-off-by: Chris Fries <cfries@google.com>
diff --git a/arch/arm64/boot/dts/google/sdm845-camera-sensor.dtsi b/arch/arm64/boot/dts/google/sdm845-camera-sensor.dtsi
old mode 100644
new mode 100755
index a715025..12ed7db
--- a/arch/arm64/boot/dts/google/sdm845-camera-sensor.dtsi
+++ b/arch/arm64/boot/dts/google/sdm845-camera-sensor.dtsi
@@ -11,14 +11,47 @@
* GNU General Public License for more details.
*/
+&tlmm {
+ /delete-node/ cam_sensor_rear_active;
+ /delete-node/ cam_sensor_rear_suspend;
+
+ cam_sensor_rear_active: cam_sensor_rear_active {
+ /* RESET, AVDD LDO */
+ mux {
+ pins = "gpio21","gpio8";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio21","gpio8";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+
+ cam_sensor_rear_suspend: cam_sensor_rear_suspend {
+ /* RESET, AVDD LDO */
+ mux {
+ pins = "gpio21","gpio8";
+ function = "gpio";
+ };
+
+ config {
+ pins = "gpio21","gpio8";
+ bias-disable; /* No PULL */
+ drive-strength = <2>; /* 2 MA */
+ };
+ };
+};
+
&soc {
led_flash_rear: qcom,camera-flash@0 {
cell-index = <0>;
reg = <0x00 0x00>;
compatible = "qcom,camera-flash";
- qcom,flash-source = <&pmi8998_flash0 &pmi8998_flash1>;
- qcom,torch-source = <&pmi8998_torch0 &pmi8998_torch1>;
- qcom,switch-source = <&pmi8998_switch0>;
+ flash-source = <&pmi8998_flash0 &pmi8998_flash1>;
+ torch-source = <&pmi8998_torch0 &pmi8998_torch1>;
+ switch-source = <&pmi8998_switch0>;
status = "ok";
};
@@ -26,9 +59,9 @@
cell-index = <1>;
reg = <0x01 0x00>;
compatible = "qcom,camera-flash";
- qcom,flash-source = <&pmi8998_flash2>;
- qcom,torch-source = <&pmi8998_torch2>;
- qcom,switch-source = <&pmi8998_switch1>;
+ flash-source = <&pmi8998_flash2>;
+ torch-source = <&pmi8998_torch2>;
+ switch-source = <&pmi8998_switch1>;
status = "ok";
};
@@ -78,36 +111,39 @@
cell-index = <0>;
reg = <0x0>;
compatible = "qcom,actuator";
- qcom,cci-master = <0>;
+ cci-master = <0>;
cam_vaf-supply = <&actuator_regulator>;
- qcom,cam-vreg-name = "cam_vaf";
- qcom,cam-vreg-min-voltage = <2800000>;
- qcom,cam-vreg-max-voltage = <2800000>;
- qcom,cam-vreg-op-mode = <0>;
+ regulator-names = "cam_vaf";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <2800000>;
+ rgltr-max-voltage = <2800000>;
+ rgltr-load-current = <0>;
};
actuator_front: qcom,actuator@1 {
cell-index = <1>;
reg = <0x1>;
compatible = "qcom,actuator";
- qcom,cci-master = <1>;
+ cci-master = <1>;
cam_vaf-supply = <&actuator_regulator>;
- qcom,cam-vreg-name = "cam_vaf";
- qcom,cam-vreg-min-voltage = <2800000>;
- qcom,cam-vreg-max-voltage = <2800000>;
- qcom,cam-vreg-op-mode = <0>;
+ regulator-names = "cam_vaf";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <2800000>;
+ rgltr-max-voltage = <2800000>;
+ rgltr-load-current = <0>;
};
ois_rear: qcom,ois@0 {
cell-index = <0>;
reg = <0x0>;
compatible = "qcom,ois";
- qcom,cci-master = <0>;
+ cci-master = <0>;
cam_vaf-supply = <&actuator_regulator>;
- qcom,cam-vreg-name = "cam_vaf";
- qcom,cam-vreg-min-voltage = <2800000>;
- qcom,cam-vreg-max-voltage = <2800000>;
- qcom,cam-vreg-op-mode = <0>;
+ regulator-names = "cam_vaf";
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <2800000>;
+ rgltr-max-voltage = <2800000>;
+ rgltr-load-current = <0>;
status = "disabled";
};
@@ -119,12 +155,13 @@
cam_vana-supply = <&pmi8998_bob>;
cam_vdig-supply = <&camera_rear_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
- qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig",
+ regulator-names = "cam_vio", "cam_vana", "cam_vdig",
"cam_clk";
- qcom,cam-vreg-min-voltage = <0 3312000 1050000 0>;
- qcom,cam-vreg-max-voltage = <0 3600000 1050000 0>;
- qcom,cam-vreg-op-mode = <0 80000 105000 0>;
- qcom,gpio-no-mux = <0>;
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <0 3312000 1050000 0>;
+ rgltr-max-voltage = <0 3600000 1050000 0>;
+ rgltr-load-current = <0 80000 105000 0>;
+ gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk0_active
&cam_sensor_rear_active>;
@@ -134,22 +171,23 @@
<&tlmm 80 0>,
<&tlmm 79 0>,
<&tlmm 27 0>;
- qcom,gpio-reset = <1>;
- qcom,gpio-vana = <2>;
- qcom,gpio-vaf = <3>;
- qcom,gpio-req-tbl-num = <0 1 2 3>;
- qcom,gpio-req-tbl-flags = <1 0 0 0>;
- qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-vaf = <3>;
+ gpio-req-tbl-num = <0 1 2 3>;
+ gpio-req-tbl-flags = <1 0 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK0",
"CAM_RESET0",
"CAM_VANA0",
"CAM_VAF";
- qcom,sensor-position = <0>;
- qcom,sensor-mode = <0>;
- qcom,cci-master = <0>;
+ sensor-position = <0>;
+ sensor-mode = <0>;
+ cci-master = <0>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
clock-names = "cam_clk";
- qcom,clock-rates = <24000000>;
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
};
eeprom_rear_aux: qcom,eeprom@1 {
@@ -160,12 +198,13 @@
cam_vio-supply = <&pm8998_lvs1>;
cam_vana-supply = <&pmi8998_bob>;
cam_clk-supply = <&titan_top_gdsc>;
- qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana",
+ regulator-names = "cam_vdig", "cam_vio", "cam_vana",
"cam_clk";
- qcom,cam-vreg-min-voltage = <1050000 0 3312000 0>;
- qcom,cam-vreg-max-voltage = <1050000 0 3600000 0>;
- qcom,cam-vreg-op-mode = <105000 0 80000 0>;
- qcom,gpio-no-mux = <0>;
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <1050000 0 3312000 0>;
+ rgltr-max-voltage = <1050000 0 3600000 0>;
+ rgltr-load-current = <105000 0 80000 0>;
+ gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk2_active
&cam_sensor_rear2_active>;
@@ -174,20 +213,21 @@
gpios = <&tlmm 15 0>,
<&tlmm 9 0>,
<&tlmm 8 0>;
- qcom,gpio-reset = <1>;
- qcom,gpio-vana = <2>;
- qcom,gpio-req-tbl-num = <0 1 2>;
- qcom,gpio-req-tbl-flags = <1 0 0>;
- qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK1",
"CAM_RESET1",
"CAM_VANA1";
- qcom,sensor-position = <0>;
- qcom,sensor-mode = <0>;
- qcom,cci-master = <1>;
+ sensor-position = <0>;
+ sensor-mode = <0>;
+ cci-master = <1>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
clock-names = "cam_clk";
- qcom,clock-rates = <24000000>;
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
};
eeprom_front: qcom,eeprom@2 {
@@ -198,12 +238,13 @@
cam_vana-supply = <&pmi8998_bob>;
cam_vdig-supply = <&camera_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
- qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig",
+ regulator-names = "cam_vio", "cam_vana", "cam_vdig",
"cam_clk";
- qcom,cam-vreg-min-voltage = <0 3312000 1050000 0>;
- qcom,cam-vreg-max-voltage = <0 3600000 1050000 0>;
- qcom,cam-vreg-op-mode = <0 80000 105000 0>;
- qcom,gpio-no-mux = <0>;
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <0 3312000 1050000 0>;
+ rgltr-max-voltage = <0 3600000 1050000 0>;
+ rgltr-load-current = <0 80000 105000 0>;
+ gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk1_active
&cam_sensor_front_active>;
@@ -213,88 +254,92 @@
<&tlmm 28 0>,
<&tlmm 8 0>,
<&tlmm 27 0>;
- qcom,gpio-reset = <1>;
- qcom,gpio-vana = <2>;
- qcom,gpio-vaf = <3>;
- qcom,gpio-req-tbl-num = <0 1 2 3>;
- qcom,gpio-req-tbl-flags = <1 0 0 0>;
- qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-vaf = <3>;
+ gpio-req-tbl-num = <0 1 2 3>;
+ gpio-req-tbl-flags = <1 0 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK2",
"CAM_RESET2",
"CAM_VANA2",
"CAM_VAF";
- qcom,sensor-position = <1>;
- qcom,sensor-mode = <0>;
- qcom,cci-master = <1>;
+ sensor-position = <1>;
+ sensor-mode = <0>;
+ cci-master = <1>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
clock-names = "cam_clk";
- qcom,clock-rates = <24000000>;
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
};
qcom,cam-sensor@0 {
cell-index = <0>;
compatible = "qcom,cam-sensor";
reg = <0x0>;
- qcom,csiphy-sd-index = <0>;
- qcom,sensor-position-roll = <90>;
- qcom,sensor-position-pitch = <0>;
- qcom,sensor-position-yaw = <180>;
- qcom,led-flash-src = <&led_flash_rear>;
- qcom,actuator-src = <&actuator_rear>;
- qcom,ois-src = <&ois_rear>;
- qcom,eeprom-src = <&eeprom_rear>;
+ csiphy-sd-index = <0>;
+ sensor-position-roll = <90>;
+ sensor-position-pitch = <0>;
+ sensor-position-yaw = <180>;
+ //led-flash-src = <&led_flash_rear>;
+ //actuator-src = <&actuator_rear>;
+ //ois-src = <&ois_rear>;
+ //eeprom-src = <&eeprom_rear>;
cam_vio-supply = <&pm8998_lvs1>;
cam_vana-supply = <&pmi8998_bob>;
- cam_vdig-supply = <&camera_rear_ldo>;
+ cam_vdig-supply = <&pm8998_s3>;
cam_clk-supply = <&titan_top_gdsc>;
- qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig",
+ regulator-names = "cam_vio", "cam_vana", "cam_vdig",
"cam_clk";
- qcom,cam-vreg-min-voltage = <0 3312000 1050000 0>;
- qcom,cam-vreg-max-voltage = <0 3600000 1050000 0>;
- qcom,cam-vreg-op-mode = <0 80000 105000 0>;
- qcom,gpio-no-mux = <0>;
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <0 3312000 1352000 0>;
+ rgltr-max-voltage = <0 3600000 1352000 0>;
+ rgltr-load-current = <0 80000 105000 0>;
+ gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
- pinctrl-0 = <&cam_sensor_mclk0_active
+ pinctrl-0 = <&cam_sensor_mclk1_active
&cam_sensor_rear_active>;
- pinctrl-1 = <&cam_sensor_mclk0_suspend
+ pinctrl-1 = <&cam_sensor_mclk1_suspend
&cam_sensor_rear_suspend>;
- gpios = <&tlmm 13 0>,
- <&tlmm 80 0>,
- <&tlmm 79 0>;
- qcom,gpio-reset = <1>;
- qcom,gpio-vana = <2>;
- qcom,gpio-req-tbl-num = <0 1 2>;
- qcom,gpio-req-tbl-flags = <1 0 0>;
- qcom,gpio-req-tbl-label = "CAMIF_MCLK0",
- "CAM_RESET0",
+ gpios = <&tlmm 14 0>,
+ <&tlmm 21 0>,
+ <&tlmm 8 0>;
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK1",
+ "CAM_RESET1",
"CAM_VANA";
- qcom,sensor-mode = <0>;
- qcom,cci-master = <0>;
+ sensor-mode = <0>;
+ cci-master = <1>;
status = "ok";
- clocks = <&clock_camcc CAM_CC_MCLK0_CLK>;
+ clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
clock-names = "cam_clk";
- qcom,clock-rates = <24000000>;
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
};
-
+/*
qcom,cam-sensor@1 {
cell-index = <1>;
compatible = "qcom,cam-sensor";
reg = <0x1>;
- qcom,csiphy-sd-index = <1>;
- qcom,sensor-position-roll = <90>;
- qcom,sensor-position-pitch = <0>;
- qcom,sensor-position-yaw = <180>;
- qcom,eeprom-src = <&eeprom_rear_aux>;
+ csiphy-sd-index = <1>;
+ sensor-position-roll = <90>;
+ sensor-position-pitch = <0>;
+ sensor-position-yaw = <180>;
+ eeprom-src = <&eeprom_rear_aux>;
cam_vdig-supply = <&camera_ldo>;
cam_vio-supply = <&pm8998_lvs1>;
cam_vana-supply = <&pmi8998_bob>;
cam_clk-supply = <&titan_top_gdsc>;
- qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana",
+ regulator-names = "cam_vdig", "cam_vio", "cam_vana",
"cam_clk";
- qcom,cam-vreg-min-voltage = <1050000 0 3312000 0>;
- qcom,cam-vreg-max-voltage = <1050000 0 3600000 0>;
- qcom,cam-vreg-op-mode = <105000 0 80000 0>;
- qcom,gpio-no-mux = <0>;
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <1050000 0 3312000 0>;
+ rgltr-max-voltage = <1050000 0 3600000 0>;
+ rgltr-load-current = <105000 0 80000 0>;
+ gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk2_active
&cam_sensor_rear2_active>;
@@ -303,42 +348,44 @@
gpios = <&tlmm 15 0>,
<&tlmm 9 0>,
<&tlmm 8 0>;
- qcom,gpio-reset = <1>;
- qcom,gpio-vana = <2>;
- qcom,gpio-req-tbl-num = <0 1 2>;
- qcom,gpio-req-tbl-flags = <1 0 0>;
- qcom,gpio-req-tbl-label = "CAMIF_MCLK1",
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK1",
"CAM_RESET1",
"CAM_VANA1";
- qcom,sensor-mode = <0>;
- qcom,cci-master = <1>;
+ sensor-mode = <0>;
+ cci-master = <1>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK2_CLK>;
clock-names = "cam_clk";
- qcom,clock-rates = <24000000>;
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
};
qcom,cam-sensor@2 {
cell-index = <2>;
compatible = "qcom,cam-sensor";
reg = <0x02>;
- qcom,csiphy-sd-index = <2>;
- qcom,sensor-position-roll = <90>;
- qcom,sensor-position-pitch = <0>;
- qcom,sensor-position-yaw = <0>;
- qcom,eeprom-src = <&eeprom_front>;
- qcom,actuator-src = <&actuator_front>;
- qcom,led-flash-src = <&led_flash_front>;
+ csiphy-sd-index = <2>;
+ sensor-position-roll = <270>;
+ sensor-position-pitch = <0>;
+ sensor-position-yaw = <0>;
+ eeprom-src = <&eeprom_front>;
+ actuator-src = <&actuator_front>;
+ led-flash-src = <&led_flash_front>;
cam_vio-supply = <&pm8998_lvs1>;
cam_vana-supply = <&pmi8998_bob>;
cam_vdig-supply = <&camera_ldo>;
cam_clk-supply = <&titan_top_gdsc>;
- qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig",
+ regulator-names = "cam_vio", "cam_vana", "cam_vdig",
"cam_clk";
- qcom,cam-vreg-min-voltage = <0 3312000 1050000 0>;
- qcom,cam-vreg-max-voltage = <0 3600000 1050000 0>;
- qcom,cam-vreg-op-mode = <0 80000 105000 0>;
- qcom,gpio-no-mux = <0>;
+ rgltr-cntrl-support;
+ rgltr-min-voltage = <0 3312000 1050000 0>;
+ rgltr-max-voltage = <0 3600000 1050000 0>;
+ rgltr-load-current = <0 80000 105000 0>;
+ gpio-no-mux = <0>;
pinctrl-names = "cam_default", "cam_suspend";
pinctrl-0 = <&cam_sensor_mclk1_active
&cam_sensor_front_active>;
@@ -347,18 +394,20 @@
gpios = <&tlmm 14 0>,
<&tlmm 28 0>,
<&tlmm 8 0>;
- qcom,gpio-reset = <1>;
- qcom,gpio-vana = <2>;
- qcom,gpio-req-tbl-num = <0 1 2>;
- qcom,gpio-req-tbl-flags = <1 0 0>;
- qcom,gpio-req-tbl-label = "CAMIF_MCLK2",
+ gpio-reset = <1>;
+ gpio-vana = <2>;
+ gpio-req-tbl-num = <0 1 2>;
+ gpio-req-tbl-flags = <1 0 0>;
+ gpio-req-tbl-label = "CAMIF_MCLK2",
"CAM_RESET2",
"CAM_VANA1";
- qcom,sensor-mode = <0>;
- qcom,cci-master = <1>;
+ sensor-mode = <0>;
+ cci-master = <1>;
status = "ok";
clocks = <&clock_camcc CAM_CC_MCLK1_CLK>;
clock-names = "cam_clk";
- qcom,clock-rates = <24000000>;
+ clock-cntl-level = "turbo";
+ clock-rates = <24000000>;
};
+*/
};
diff --git a/arch/arm64/boot/dts/google/sdm845-v1-b1c1-common.dtsi b/arch/arm64/boot/dts/google/sdm845-v1-b1c1-common.dtsi
old mode 100644
new mode 100755
index 563685a..fb35218
--- a/arch/arm64/boot/dts/google/sdm845-v1-b1c1-common.dtsi
+++ b/arch/arm64/boot/dts/google/sdm845-v1-b1c1-common.dtsi
@@ -15,6 +15,7 @@
/* for now, keep it as default MTP */
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/qcom,camcc-sdm845.h>
#include "sdm845-camera-sensor.dtsi"
#include "sdm845-b1c1-pinctrl.dtsi"
#include "sdm845-b1c1-haptics.dtsi"
