| /* |
| * Copyright (c) 2019, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| &soc { |
| led_flash0: qcom,camera-flash@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera-flash"; |
| qcom,flash-source = <&pmi632_flash0 &pmi632_flash1>; |
| qcom,torch-source = <&pmi632_torch0 &pmi632_torch1>; |
| qcom,switch-source = <&pmi632_switch0 &pmi632_switch0>; |
| status = "ok"; |
| }; |
| }; |
| |
| &cci { |
| actuator0: qcom,actuator@0 { |
| cell-index = <0>; |
| reg = <0x0>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| cam_vaf-supply = <&L5P>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <2800000>; |
| qcom,cam-vreg-max-voltage = <2800000>; |
| qcom,cam-vreg-op-mode = <0>; |
| }; |
| |
| eeprom0: qcom,eeprom@0 { |
| cell-index = <0>; |
| reg = <0>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L12A>; |
| cam_vana-supply = <&L3P>; |
| cam_vdig-supply = <&L2P>; |
| cam_clk-supply = <&camss_top_gdsc>; |
| cam_vaf-supply = <&L5P>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk", "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <1800000 2800000 1104000 0 2800000>; |
| qcom,cam-vreg-max-voltage = <1800000 2800000 1104000 0 2800000>; |
| qcom,cam-vreg-op-mode = <0 80000 105000 0 100000>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_rear_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_rear_suspend>; |
| gpios = <&tlmm 34 0>, |
| <&tlmm 48 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0"; |
| qcom,sensor-position = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&clock_gcc GCC_CAMSS_MCLK0_CLK_SRC>, |
| <&clock_gcc GCC_CAMSS_MCLK0_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| eeprom1: qcom,eeprom@1 { |
| cell-index = <1>; |
| reg = <0x1>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&L12A>; |
| cam_vana-supply = <&L4P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&camss_top_gdsc>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| qcom,cam-vreg-min-voltage = <1800000 2800000 1200000 0>; |
| qcom,cam-vreg-max-voltage = <1800000 2800000 1200000 0>; |
| qcom,cam-vreg-op-mode = <0 80000 105000 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active |
| &cam_sensor_front_active>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend |
| &cam_sensor_front_suspend>; |
| gpios = <&tlmm 36 0>, |
| <&tlmm 42 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_gcc GCC_CAMSS_MCLK2_CLK_SRC>, |
| <&clock_gcc GCC_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x0>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <90>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,eeprom-src = <&eeprom0>; |
| qcom,led-flash-src = <&led_flash0>; |
| cam_vio-supply = <&L12A>; |
| cam_vana-supply = <&L3P>; |
| cam_vdig-supply = <&L2P>; |
| cam_clk-supply = <&camss_top_gdsc>; |
| cam_vaf-supply = <&L5P>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk", "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <1800000 2800000 1104000 0 2800000>; |
| qcom,cam-vreg-max-voltage = <1800000 2800000 1104000 0 2800000>; |
| qcom,cam-vreg-op-mode = <0 80000 105000 0 100000>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_rear_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_rear_suspend>; |
| gpios = <&tlmm 34 0>, |
| <&tlmm 48 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&clock_gcc GCC_CAMSS_MCLK0_CLK_SRC>, |
| <&clock_gcc GCC_CAMSS_MCLK0_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@1 { |
| cell-index = <1>; |
| compatible = "qcom,camera"; |
| reg = <0x1>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <90>; |
| cam_vio-supply = <&L12A>; |
| cam_vana-supply = <&L4P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&camss_top_gdsc>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| qcom,cam-vreg-min-voltage = <1800000 2800000 1200000 0>; |
| qcom,cam-vreg-max-voltage = <1800000 2800000 1200000 0>; |
| qcom,cam-vreg-op-mode = <0 80000 105000 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_active |
| &cam_sensor_rear2_active>; |
| pinctrl-1 = <&cam_sensor_mclk1_suspend |
| &cam_sensor_rear2_suspend>; |
| gpios = <&tlmm 35 0>, |
| <&tlmm 46 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK1", |
| "CAM_RESET1"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_gcc GCC_CAMSS_MCLK1_CLK_SRC>, |
| <&clock_gcc GCC_CAMSS_MCLK1_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@2 { |
| cell-index = <2>; |
| compatible = "qcom,camera"; |
| reg = <0x02>; |
| qcom,csiphy-sd-index = <2>; |
| qcom,csid-sd-index = <2>; |
| qcom,mount-angle = <90>; |
| qcom,eeprom-src = <&eeprom1>; |
| cam_vio-supply = <&L12A>; |
| cam_vana-supply = <&L4P>; |
| cam_vdig-supply = <&L1P>; |
| cam_clk-supply = <&camss_top_gdsc>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig", |
| "cam_clk"; |
| qcom,cam-vreg-min-voltage = <1800000 2800000 1200000 0>; |
| qcom,cam-vreg-max-voltage = <1800000 2800000 1200000 0>; |
| qcom,cam-vreg-op-mode = <0 80000 105000 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active |
| &cam_sensor_front_active>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend |
| &cam_sensor_front_suspend>; |
| gpios = <&tlmm 36 0>, |
| <&tlmm 42 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2"; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_gcc GCC_CAMSS_MCLK2_CLK_SRC>, |
| <&clock_gcc GCC_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| }; |
