| /* Copyright (c) 2015, LGE Inc. All rights reserved. |
| * Copyright (c) 2014, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| &soc { |
| led_flash0: qcom,camera-flash { |
| cell-index = <0>; |
| compatible = "qcom,camera-flash"; |
| qcom,flash-type = <1>; |
| qcom,flash-source = <&pmi8994_flash0 &pmi8994_flash1>; |
| qcom,torch-source = <&pmi8994_torch0 &pmi8994_torch1>; |
| qcom,switch-source = <&pmi8994_switch>; |
| }; |
| |
| tof0: stmvl6180@0 { |
| cell-index = <0x0>; |
| compatible = "st,stmvl6180"; |
| qcom,cci-master = <0>; |
| cam_tof-supply = <&pm8994_l17>; |
| cam_vio-supply = <&pm8994_lvs1>; |
| qcom,cam-vreg-name = "cam_vio", "cam_tof"; |
| qcom,cam-vreg-min-voltage = <0 2700000>; |
| qcom,cam-vreg-max-voltage = <0 2700000>; |
| qcom,cam-vreg-op-mode = <0 100000>; |
| qcom,i2c-freq-mode = <0>; |
| qcom,slave-addr = <0x29>; |
| stmvl6180,ldaf-en-gpio = <&msm_gpio 74 0>; |
| stmvl6180,ldaf-int-gpio = <&msm_gpio 95 0>; |
| status = "ok"; |
| }; |
| }; |
| |
| &cci { |
| actuator0: qcom,actuator@0 { |
| cell-index = <0>; |
| reg = <0x0>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| cam_vaf-supply = <&pm8994_l23>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <2800000>; |
| qcom,cam-vreg-max-voltage = <2800000>; |
| qcom,cam-vreg-op-mode = <100000>; |
| }; |
| |
| eeprom5: qcom,eeprom@5 { |
| cell-index = <5>; |
| reg = <0x5>; |
| qcom,eeprom-name = "m24c64s"; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0xa2>; |
| qcom,cci-master = <0>; |
| qcom,num-blocks = <1>; |
| |
| qcom,page0 = <0 0 0 0 0 0>; |
| qcom,poll0 = <0 0 0 0 0 0>; |
| qcom,saddr0 = <0xa2>; |
| qcom,mem0 = <2012 0x0000 2 0 1 0>; |
| |
| cam_vio-supply = <&pm8994_lvs1>; |
| qcom,cam-vreg-name = "cam_vio"; |
| qcom,cam-vreg-min-voltage = <0>; |
| qcom,cam-vreg-max-voltage = <0>; |
| qcom,cam-vreg-op-mode = <0>; |
| qcom,cam-power-seq-type = "sensor_vreg"; |
| qcom,cam-power-seq-val = "cam_vio"; |
| qcom,cam-power-seq-cfg-val = <1>; |
| qcom,cam-power-seq-delay = <1>; |
| |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active &cam_sensor_rear_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend &cam_sensor_rear_suspend>; |
| gpios = <&msm_gpio 13 0>, |
| <&msm_gpio 92 0>, |
| <&msm_gpio 91 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0", |
| "CAM_STANDBY0"; |
| status = "ok"; |
| }; |
| |
| qcom,camera@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x0>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,sensor-name = "imx377"; |
| qcom,mount-angle = <270>; |
| qcom,eeprom-src = <&eeprom5>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,led-flash-src = <&led_flash0>; |
| cam_vdig-supply = <&pm8994_l3>; |
| cam_vio-supply = <&pm8994_lvs1>; |
| cam_vana-supply = <&pm8994_l17>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-min-voltage = <1200000 0 2700000>; |
| qcom,cam-vreg-max-voltage = <1200000 0 2700000>; |
| qcom,cam-vreg-op-mode = <105000 0 80000>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active &cam_sensor_rear_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend &cam_sensor_rear_suspend>; |
| gpios = <&msm_gpio 13 0>, |
| <&msm_gpio 92 0>, |
| <&msm_gpio 91 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-standby = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0", |
| "CAM_STANDBY0"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&clock_mmss clk_mclk0_clk_src>, |
| <&clock_mmss clk_camss_mclk0_clk>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| }; |
| |
| ov5693_eeprom: qcom,eeprom@a0 { |
| cell-index = <1>; |
| reg = <0xa0 0x0>; |
| compatible = "qcom,eeprom"; |
| qcom,slave-addr = <0xa0>; |
| qcom,cci-master = <1>; |
| qcom,eeprom-name = "brcb032gwz"; |
| qcom,num-blocks = <1>; |
| |
| qcom,page0 = <0 0 0 0 0 0>; |
| qcom,poll0 = <0 0 0 0 0 0>; |
| qcom,mem0 = <0x800 0x0000 2 0 1 0>; |
| |
| cam_vio-supply = <&pm8994_l10>; |
| qcom,cam-vreg-name = "cam_vio"; |
| qcom,cam-vreg-min-voltage = <0>; |
| qcom,cam-vreg-max-voltage = <0>; |
| qcom,cam-vreg-op-mode = <0>; |
| qcom,cam-power-seq-type = "sensor_vreg"; |
| qcom,cam-power-seq-val = "cam_vio"; |
| qcom,cam-power-seq-cfg-val = <1>; |
| qcom,cam-power-seq-delay = <1>; |
| |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active &cam_sensor_front_active>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend &cam_sensor_front_suspend>; |
| gpios = <&msm_gpio 15 0>, |
| <&msm_gpio 104 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2"; |
| status = "ok"; |
| }; |
| |
| lge,camera1@6c { |
| cell-index = <1>; |
| compatible = "qcom,camera"; |
| reg = <0x6c>; |
| qcom,slave-id = <0x6c 0x300a 0x5690>; |
| qcom,csiphy-sd-index = <2>; |
| qcom,csid-sd-index = <2>; |
| qcom,eeprom-src = <&ov5693_eeprom>; |
| qcom,mount-angle = <90>; |
| qcom,sensor-name = "ov5693"; |
| cam_vdig-supply = <&pm8994_l14>; |
| cam_vio-supply = <&pm8994_l10>; |
| cam_vana-supply = <&pm8994_l29>; |
| qcom,cam-vreg-name = "cam_vdig", "cam_vio", "cam_vana"; |
| qcom,cam-vreg-type = <0 0 0>; |
| qcom,cam-vreg-min-voltage = <1200000 1800000 2800000>; |
| qcom,cam-vreg-max-voltage = <1200000 1800000 2800000>; |
| qcom,cam-vreg-op-mode = <1200000 1800000 2800000>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active &cam_sensor_front_active>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend &cam_sensor_front_suspend>; |
| gpios = <&msm_gpio 15 0>, /* VT_CAM_MCLK */ |
| <&msm_gpio 104 0>; /* VT_CAM_RESET_N */ |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2"; |
| qcom,csi-lane-assign = <0x4320>; |
| qcom,csi-lane-mask = <0x7>; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <1>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_mmss clk_mclk2_clk_src>, |
| <&clock_mmss clk_camss_mclk2_clk>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| }; |
| }; |
