| menuconfig POWER_SUPPLY |
| tristate "Power supply class support" |
| help |
| Say Y here to enable power supply class support. This allows |
| power supply (batteries, AC, USB) monitoring by userspace |
| via sysfs and uevent (if available) and/or APM kernel interface |
| (if selected below). |
| |
| if POWER_SUPPLY |
| |
| config POWER_SUPPLY_DEBUG |
| bool "Power supply debug" |
| help |
| Say Y here to enable debugging messages for power supply class |
| and drivers. |
| |
| config PDA_POWER |
| tristate "Generic PDA/phone power driver" |
| depends on !S390 |
| help |
| Say Y here to enable generic power driver for PDAs and phones with |
| one or two external power supplies (AC/USB) connected to main and |
| backup batteries, and optional builtin charger. |
| |
| config APM_POWER |
| tristate "APM emulation for class batteries" |
| depends on APM_EMULATION |
| help |
| Say Y here to enable support APM status emulation using |
| battery class devices. |
| |
| config MAX8925_POWER |
| tristate "MAX8925 battery charger support" |
| depends on MFD_MAX8925 |
| help |
| Say Y here to enable support for the battery charger in the Maxim |
| MAX8925 PMIC. |
| |
| config WM831X_BACKUP |
| tristate "WM831X backup battery charger support" |
| depends on MFD_WM831X |
| help |
| Say Y here to enable support for the backup battery charger |
| in the Wolfson Microelectronics WM831x PMICs. |
| |
| config WM831X_POWER |
| tristate "WM831X PMU support" |
| depends on MFD_WM831X |
| help |
| Say Y here to enable support for the power management unit |
| provided by Wolfson Microelectronics WM831x PMICs. |
| |
| config WM8350_POWER |
| tristate "WM8350 PMU support" |
| depends on MFD_WM8350 |
| help |
| Say Y here to enable support for the power management unit |
| provided by the Wolfson Microelectronics WM8350 PMIC. |
| |
| config TEST_POWER |
| tristate "Test power driver" |
| help |
| This driver is used for testing. It's safe to say M here. |
| |
| config BATTERY_DS2760 |
| tristate "DS2760 battery driver (HP iPAQ & others)" |
| depends on W1 && W1_SLAVE_DS2760 |
| help |
| Say Y here to enable support for batteries with ds2760 chip. |
| |
| config BATTERY_DS2780 |
| tristate "DS2780 battery driver" |
| depends on HAS_IOMEM |
| select W1 |
| select W1_SLAVE_DS2780 |
| help |
| Say Y here to enable support for batteries with ds2780 chip. |
| |
| config BATTERY_DS2781 |
| tristate "2781 battery driver" |
| depends on HAS_IOMEM |
| select W1 |
| select W1_SLAVE_DS2781 |
| help |
| If you enable this you will have the DS2781 battery driver support. |
| |
| The battery monitor chip is used in many batteries/devices |
| as the one who is responsible for charging/discharging/monitoring |
| Li+ batteries. |
| |
| If you are unsure, say N. |
| |
| config BATTERY_DS2782 |
| tristate "DS2782/DS2786 standalone gas-gauge" |
| depends on I2C |
| help |
| Say Y here to enable support for the DS2782/DS2786 standalone battery |
| gas-gauge. |
| |
| config BATTERY_PMU |
| tristate "Apple PMU battery" |
| depends on PPC32 && ADB_PMU |
| help |
| Say Y here to expose battery information on Apple machines |
| through the generic battery class. |
| |
| config BATTERY_OLPC |
| tristate "One Laptop Per Child battery" |
| depends on X86_32 && OLPC |
| help |
| Say Y to enable support for the battery on the OLPC laptop. |
| |
| config BATTERY_TOSA |
| tristate "Sharp SL-6000 (tosa) battery" |
| depends on MACH_TOSA && MFD_TC6393XB && TOUCHSCREEN_WM97XX |
| help |
| Say Y to enable support for the battery on the Sharp Zaurus |
| SL-6000 (tosa) models. |
| |
| config BATTERY_COLLIE |
| tristate "Sharp SL-5500 (collie) battery" |
| depends on SA1100_COLLIE && MCP_UCB1200 |
| help |
| Say Y to enable support for the battery on the Sharp Zaurus |
| SL-5500 (collie) models. |
| |
| config BATTERY_WM97XX |
| bool "WM97xx generic battery driver" |
| depends on TOUCHSCREEN_WM97XX=y |
| help |
| Say Y to enable support for battery measured by WM97xx aux port. |
| |
| config BATTERY_SBS |
| tristate "SBS Compliant gas gauge" |
| depends on I2C |
| help |
| Say Y to include support for SBS battery driver for SBS-compliant |
| gas gauges. |
| |
| config BATTERY_BQ27x00 |
| tristate "BQ27x00 battery driver" |
| help |
| Say Y here to enable support for batteries with BQ27x00 (I2C/HDQ) chips. |
| |
| config BATTERY_BQ27X00_I2C |
| bool "BQ27200/BQ27500 support" |
| depends on BATTERY_BQ27x00 |
| depends on I2C |
| default y |
| help |
| Say Y here to enable support for batteries with BQ27x00 (I2C) chips. |
| |
| config BATTERY_BQ27X00_PLATFORM |
| bool "BQ27000 support" |
| depends on BATTERY_BQ27x00 |
| default y |
| help |
| Say Y here to enable support for batteries with BQ27000 (HDQ) chips. |
| |
| config BATTERY_DA9030 |
| tristate "DA9030 battery driver" |
| depends on PMIC_DA903X |
| help |
| Say Y here to enable support for batteries charger integrated into |
| DA9030 PMIC. |
| |
| config BATTERY_DA9052 |
| tristate "Dialog DA9052 Battery" |
| depends on PMIC_DA9052 |
| depends on BROKEN |
| help |
| Say Y here to enable support for batteries charger integrated into |
| DA9052 PMIC. |
| |
| config BATTERY_MAX17040 |
| tristate "Maxim MAX17040 Fuel Gauge" |
| depends on I2C |
| help |
| MAX17040 is fuel-gauge systems for lithium-ion (Li+) batteries |
| in handheld and portable equipment. The MAX17040 is configured |
| to operate with a single lithium cell |
| |
| config BATTERY_MAX17042 |
| tristate "Maxim MAX17042/8997/8966 Fuel Gauge" |
| depends on I2C |
| help |
| MAX17042 is fuel-gauge systems for lithium-ion (Li+) batteries |
| in handheld and portable equipment. The MAX17042 is configured |
| to operate with a single lithium cell. MAX8997 and MAX8966 are |
| multi-function devices that include fuel gauages that are compatible |
| with MAX17042. |
| |
| config BATTERY_Z2 |
| tristate "Z2 battery driver" |
| depends on I2C && MACH_ZIPIT2 |
| help |
| Say Y to include support for the battery on the Zipit Z2. |
| |
| config BATTERY_S3C_ADC |
| tristate "Battery driver for Samsung ADC based monitoring" |
| depends on S3C_ADC |
| help |
| Say Y here to enable support for iPAQ h1930/h1940/rx1950 battery |
| |
| config CHARGER_PCF50633 |
| tristate "NXP PCF50633 MBC" |
| depends on MFD_PCF50633 |
| help |
| Say Y to include support for NXP PCF50633 Main Battery Charger. |
| |
| config BATTERY_JZ4740 |
| tristate "Ingenic JZ4740 battery" |
| depends on MACH_JZ4740 |
| depends on MFD_JZ4740_ADC |
| help |
| Say Y to enable support for the battery on Ingenic JZ4740 based |
| boards. |
| |
| This driver can be build as a module. If so, the module will be |
| called jz4740-battery. |
| |
| config BATTERY_INTEL_MID |
| tristate "Battery driver for Intel MID platforms" |
| depends on INTEL_SCU_IPC && SPI |
| help |
| Say Y here to enable the battery driver on Intel MID |
| platforms. |
| |
| config CHARGER_ISP1704 |
| tristate "ISP1704 USB Charger Detection" |
| depends on USB_OTG_UTILS |
| help |
| Say Y to enable support for USB Charger Detection with |
| ISP1707/ISP1704 USB transceivers. |
| |
| config CHARGER_MAX8903 |
| tristate "MAX8903 Battery DC-DC Charger for USB and Adapter Power" |
| depends on GENERIC_HARDIRQS |
| help |
| Say Y to enable support for the MAX8903 DC-DC charger and sysfs. |
| The driver supports controlling charger-enable and current-limit |
| pins based on the status of charger connections with interrupt |
| handlers. |
| |
| config CHARGER_TWL4030 |
| tristate "OMAP TWL4030 BCI charger driver" |
| depends on TWL4030_CORE |
| help |
| Say Y here to enable support for TWL4030 Battery Charge Interface. |
| |
| config CHARGER_LP8727 |
| tristate "TI/National Semiconductor LP8727 charger driver" |
| depends on I2C |
| help |
| Say Y here to enable support for LP8727 Charger Driver. |
| |
| config CHARGER_GPIO |
| tristate "GPIO charger" |
| depends on GPIOLIB |
| help |
| Say Y to include support for chargers which report their online status |
| through a GPIO pin. |
| |
| This driver can be build as a module. If so, the module will be |
| called gpio-charger. |
| |
| config CHARGER_MANAGER |
| bool "Battery charger manager for multiple chargers" |
| depends on REGULATOR && RTC_CLASS |
| help |
| Say Y to enable charger-manager support, which allows multiple |
| chargers attached to a battery and multiple batteries attached to a |
| system. The charger-manager also can monitor charging status in |
| runtime and in suspend-to-RAM by waking up the system periodically |
| with help of suspend_again support. |
| |
| config CHARGER_MAX8997 |
| tristate "Maxim MAX8997/MAX8966 PMIC battery charger driver" |
| depends on MFD_MAX8997 && REGULATOR_MAX8997 |
| help |
| Say Y to enable support for the battery charger control sysfs and |
| platform data of MAX8997/LP3974 PMICs. |
| |
| config CHARGER_MAX8998 |
| tristate "Maxim MAX8998/LP3974 PMIC battery charger driver" |
| depends on MFD_MAX8998 && REGULATOR_MAX8998 |
| help |
| Say Y to enable support for the battery charger control sysfs and |
| platform data of MAX8998/LP3974 PMICs. |
| |
| config BATTERY_MSM |
| tristate "MSM battery" |
| depends on ARCH_MSM && MSM_ONCRPCROUTER |
| help |
| Say Y to enable support for the battery in Qualcomm MSM. |
| |
| config BATTERY_MSM_FAKE |
| tristate "Fake MSM battery" |
| depends on ARCH_MSM && BATTERY_MSM |
| default n |
| help |
| Say Y to bypass actual battery queries. |
| |
| config BATTERY_MSM8X60 |
| tristate "MSM8X60 battery" |
| select PMIC8XXX_BATTALARM |
| help |
| Some MSM boards have dual charging paths to charge the battery. |
| Say Y to enable support for the battery charging in |
| such devices. |
| |
| config PM8058_CHARGER |
| tristate "pmic8058 charger" |
| depends on BATTERY_MSM8X60 |
| depends on PMIC8058 |
| help |
| Say Y to enable support for battery charging from the pmic8058. |
| pmic8058 provides a linear charging circuit connected to the usb |
| cable on Qualcomm's msm8x60 surf board. |
| |
| config ISL9519_CHARGER |
| tristate "isl9519 charger" |
| depends on (BATTERY_MSM8X60 || PM8921_CHARGER) |
| depends on I2C |
| default n |
| help |
| The isl9519q charger chip from intersil is connected to an external |
| charger cable and is preferred way of charging the battery because |
| of its high current rating. |
| Choose Y if you are compiling for Qualcomm's msm8x60 surf/ffa board. |
| |
| config SMB137B_CHARGER |
| tristate "smb137b charger" |
| default n |
| depends on I2C |
| help |
| The smb137b charger chip from summit is a switching mode based |
| charging solution. |
| Choose Y if you are compiling for Qualcomm's msm8x60 fluid board. |
| To compile this driver as a module, choose M here: the module will |
| be called smb137b. |
| |
| config SMB137C_CHARGER |
| tristate "Summit SMB137C Battery Charger" |
| depends on I2C |
| depends on OF |
| help |
| The SMB137C charger chip from Summit is a switching mode based |
| charging solution. This driver supports enabling and disabling |
| charging, setting the input current limit, and enabling USB OTG mode |
| in order to supply 5 V on the VBUS line. |
| |
| config SMB349_CHARGER |
| tristate "smb349 charger" |
| depends on I2C |
| help |
| Say Y to enable support for the SMB349 switching mode based charger |
| and sysfs. The driver supports controlling charger-enable and |
| current limiting capabilities. The driver also lets the |
| SMB349 be operated as a slave device via the power supply |
| framework. |
| |
| config SMB350_CHARGER |
| tristate "smb350 charger" |
| depends on I2C |
| help |
| Say Y to enable battery charging by SMB350 switching mode based |
| external charger. The device supports stack-cell battery charging. |
| The driver configures the device volatile parameters |
| and the charger device works autonomously. |
| The driver supports charger-enable and charger-suspend/resume. |
| The driver reports the charger status via the power supply framework. |
| A charger status change triggers an IRQ via the device STAT pin. |
| |
| config PM8058_FIX_USB |
| tristate "pmic8058 software workaround for usb removal" |
| depends on PMIC8058 |
| depends on !PM8058_CHARGER |
| help |
| Say Y to enable the software workaround to USB Vbus line |
| staying high even when USB cable is removed. This option |
| is in lieu of a complete pm8058 charging driver. |
| |
| config BATTERY_QCIBAT |
| tristate "Quanta Computer Inc. Battery" |
| depends on SENSORS_WPCE775X |
| default n |
| help |
| Say Y here if you want to use the Quanta battery driver for ST15 |
| platform. |
| |
| config BATTERY_BQ27520 |
| tristate "BQ27520 battery driver" |
| depends on I2C |
| default n |
| help |
| Say Y here to enable support for batteries with BQ27520 (I2C) chips. |
| |
| config BQ27520_TEST_ENABLE |
| bool "Enable BQ27520 Fuel Gauge Chip Test" |
| depends on BATTERY_BQ27520 |
| default n |
| help |
| Say Y here to enable Test sysfs Interface for BQ27520 Drivers. |
| |
| config BATTERY_BQ27541 |
| tristate "BQ27541 battery driver" |
| depends on I2C |
| default n |
| help |
| Say Y here to enable support for batteries with BQ27541 (I2C) chips. |
| |
| config BATTERY_BQ28400 |
| tristate "BQ28400 battery driver" |
| depends on I2C |
| default n |
| help |
| Say Y here to enable support for batteries with BQ28400 (I2C) chips. |
| The bq28400 Texas Instruments Inc device monitors the battery |
| charging/discharging status via Rsens resistor, typically 10 mohm. |
| It monitors the battery temperature via Thermistor. |
| The device monitors the battery level (Relative-State-Of-Charge). |
| The device is SBS compliant, providing battery info over I2C. |
| |
| config PM8921_CHARGER |
| tristate "PM8921 Charger driver" |
| depends on MFD_PM8921_CORE |
| help |
| Say Y here to enable support for pm8921 chip charger subdevice |
| |
| config QPNP_CHARGER |
| tristate "QPNP Charger driver" |
| depends on SPMI |
| depends on OF_SPMI |
| depends on THERMAL_QPNP_ADC_TM |
| help |
| Say Y here to enable the switch mode battery charger |
| and boost device which supports USB detection and charging. The driver |
| also offers relevant information to userspace via the power supply |
| framework. |
| |
| config PM8XXX_CCADC |
| tristate "PM8XXX battery current adc driver" |
| depends on MFD_PM8921_CORE |
| help |
| Say Y here to enable support for pm8921 chip bms subdevice |
| |
| config LTC4088_CHARGER |
| tristate "LTC4088 Charger driver" |
| depends on GPIOLIB |
| help |
| Say Y here to enable support for ltc4088 chip charger. It controls the |
| operations through GPIO pins. |
| |
| config PM8921_BMS |
| select PM8XXX_CCADC |
| tristate "PM8921 Battery Monitoring System driver" |
| depends on MFD_PM8921_CORE |
| help |
| Say Y here to enable support for pm8921 chip bms subdevice |
| |
| config BATTERY_BCL |
| tristate "Battery Current Limit driver" |
| help |
| Say Y here to enable support for battery current limit |
| device. The BCL driver will poll BMS if |
| thermal daemon enables BCL. |
| It will notify thermal daemon if IBat crosses Imax threshold. |
| |
| config CHARGER_SMB347 |
| tristate "Summit Microelectronics SMB347 Battery Charger" |
| depends on I2C |
| help |
| Say Y to include support for Summit Microelectronics SMB347 |
| Battery Charger. |
| |
| config AB8500_BM |
| bool "AB8500 Battery Management Driver" |
| depends on AB8500_CORE && AB8500_GPADC |
| help |
| Say Y to include support for AB5500 battery management. |
| |
| config AB8500_BATTERY_THERM_ON_BATCTRL |
| bool "Thermistor connected on BATCTRL ADC" |
| depends on AB8500_BM |
| help |
| Say Y to enable battery temperature measurements using |
| thermistor connected on BATCTRL ADC. |
| |
| config QPNP_BMS |
| tristate "QPNP Battery Monitoring System driver" |
| depends on SPMI |
| depends on MSM_QPNP_INT |
| help |
| Say Y here to enable support for QPNP chip bms device. |
| It registers a fuelgauge bms power supply to report |
| State of Charge. |
| |
| config MAX17048_FUELGAUGE |
| tristate "Maxim MAX17048 fuel gauging external driver" |
| depends on I2C |
| default n |
| help |
| MAX17048 is fuel-gauge systems for lithium-ion (Li+) batteries |
| in handheld and portable equipment. The MAX17048 is configured |
| to operate with a single lithium cell |
| |
| config BQ51013B_CHARGER |
| tristate "TI BQ51013B wireless charger driver" |
| default n |
| help |
| The BQ51013B is an devices for wireless power transfer in portable |
| applications. The BQ51013B provide the AC/DC power conversion while |
| intergrating the digital control required to comply with Qi v1.1 |
| protocol. |
| |
| config BQ24192_CHARGER |
| tristate "TI BQ24192 charger driver" |
| depends on I2C |
| default n |
| help |
| The BQ24192 is a highly-integrated switch-mode battery charge |
| management and system power path management device for 1 cell |
| Li-Ion and Li-Polymer battery. |
| |
| config BATTERY_TEMP_CONTROL |
| bool "Battery Temperature Control Configuration" |
| default n |
| help |
| Say Y to enable battery temperature control for safety. |
| It controls charging current depending on battery temperature. |
| |
| endif # POWER_SUPPLY |
