| /* |
| * Copyright (c) 2016-2017, 2019, The Linux Foundation. All rights reserved. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 and |
| * only version 2 as published by the Free Software Foundation. |
| * |
| * This program is distributed in the hope that it will be useful, |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the |
| * GNU General Public License for more details. |
| */ |
| |
| &soc { |
| led_flash0: qcom,camera-flash@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera-flash"; |
| qcom,flash-source = <&pm660l_flash0 &pm660l_flash1>; |
| qcom,torch-source = <&pm660l_torch0 &pm660l_torch1>; |
| qcom,switch-source = <&pm660l_switch0>; |
| status = "ok"; |
| }; |
| |
| led_flash1: qcom,camera-flash@1 { |
| cell-index = <1>; |
| compatible = "qcom,camera-flash"; |
| qcom,flash-source = <&pm660l_flash2>; |
| qcom,torch-source = <&pm660l_torch2>; |
| qcom,switch-source = <&pm660l_switch1>; |
| status = "ok"; |
| }; |
| |
| cam_avdd_gpio_regulator: cam_avdd_fixed_regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "cam_avdd_gpio_regulator"; |
| regulator-min-microvolt = <3600000>; |
| regulator-max-microvolt = <3600000>; |
| enable-active-high; |
| gpio = <&tlmm 51 0>; |
| vin-supply = <&pm660l_bob>; |
| }; |
| |
| cam_actuator_regulator: cam_actuator_fixed_regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "cam_actuator_regulator"; |
| regulator-min-microvolt = <3600000>; |
| regulator-max-microvolt = <3600000>; |
| enable-active-high; |
| gpio = <&tlmm 50 0>; |
| vin-supply = <&pm660l_bob>; |
| }; |
| |
| cam_dvdd_gpio_regulator: cam_dvdd_fixed_regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "cam_dvdd_gpio_regulator"; |
| regulator-min-microvolt = <1350000>; |
| regulator-max-microvolt = <1350000>; |
| enable-active-high; |
| gpio = <&pm660l_gpios 3 0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cam_sensor_eldo3_default>; |
| vin-supply = <&pm660_s5>; |
| }; |
| |
| cam_rear_dvdd_gpio_regulator: cam_rear_dvdd_fixed_regulator { |
| compatible = "regulator-fixed"; |
| regulator-name = "cam_rear_dvdd_gpio_regulator"; |
| regulator-min-microvolt = <1350000>; |
| regulator-max-microvolt = <1350000>; |
| enable-active-high; |
| gpio = <&pm660l_gpios 4 0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&cam_sensor_eldo4_default>; |
| vin-supply = <&pm660_s5>; |
| }; |
| }; |
| |
| &cci { |
| actuator0: qcom,actuator@0 { |
| cell-index = <0>; |
| reg = <0x0>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <0>; |
| cam_vaf-supply = <&cam_actuator_regulator>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <3600000>; |
| qcom,cam-vreg-max-voltage = <3600000>; |
| qcom,cam-vreg-op-mode = <0>; |
| }; |
| |
| actuator1: qcom,actuator@1 { |
| cell-index = <1>; |
| reg = <0x1>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <1>; |
| cam_vaf-supply = <&cam_actuator_regulator>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <3600000>; |
| qcom,cam-vreg-max-voltage = <3600000>; |
| qcom,cam-vreg-op-mode = <0>; |
| }; |
| |
| actuator2: qcom,actuator@2 { |
| cell-index = <2>; |
| reg = <0x2>; |
| compatible = "qcom,actuator"; |
| qcom,cci-master = <1>; |
| cam_vaf-supply = <&cam_actuator_regulator>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <3600000>; |
| qcom,cam-vreg-max-voltage = <3600000>; |
| qcom,cam-vreg-op-mode = <0>; |
| }; |
| |
| ois0: qcom,ois@0 { |
| cell-index = <0>; |
| reg = <0x0>; |
| compatible = "qcom,ois"; |
| qcom,cci-master = <0>; |
| cam_vaf-supply = <&cam_actuator_regulator>; |
| qcom,cam-vreg-name = "cam_vaf"; |
| qcom,cam-vreg-min-voltage = <3600000>; |
| qcom,cam-vreg-max-voltage = <3600000>; |
| qcom,cam-vreg-op-mode = <0>; |
| status = "disabled"; |
| }; |
| |
| tof0: qcom,tof@29{ |
| cell-index = <0>; |
| reg = <0x29>; |
| compatible = "st,stmvl53l0"; |
| qcom,cci-master = <0>; |
| cam_laser-supply = <&cam_actuator_regulator>; |
| qcom,cam-vreg-name = "cam_laser"; |
| qcom,cam-vreg-min-voltage = <3600000>; |
| qcom,cam-vreg-max-voltage = <3600000>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_tof_active>; |
| pinctrl-1 = <&cam_tof_suspend>; |
| stm,irq-gpio = <&tlmm 45 0x2008>; |
| gpios = <&tlmm 42 0>; |
| qcom,gpio-req-tbl-num = <0>; |
| qcom,gpio-req-tbl-flags = <0>; |
| qcom,gpio-req-tbl-label = "RNG_EN"; |
| }; |
| |
| eeprom0: qcom,eeprom@0 { |
| cell-index = <0>; |
| reg = <0>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&pm660_l11>; |
| cam_vana-supply = <&cam_avdd_gpio_regulator>; |
| cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig"; |
| qcom,cam-vreg-min-voltage = <1780000 0 0>; |
| qcom,cam-vreg-max-voltage = <1950000 0 0>; |
| qcom,cam-vreg-op-mode = <105000 0 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_rear_active |
| &cam_actuator_vaf_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_rear_suspend |
| &cam_actuator_vaf_suspend>; |
| gpios = <&tlmm 32 0>, |
| <&tlmm 46 0>, |
| <&tlmm 50 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-vaf = <2>; |
| qcom,gpio-req-tbl-num = <0 1 2>; |
| qcom,gpio-req-tbl-flags = <1 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0", |
| "CAM_VAF"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&clock_mmss MCLK0_CLK_SRC>, |
| <&clock_mmss MMSS_CAMSS_MCLK0_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| eeprom1: qcom,eeprom@1 { |
| cell-index = <1>; |
| reg = <0x1>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&pm660_l11>; |
| cam_vana-supply = <&cam_avdd_gpio_regulator>; |
| cam_vdig-supply = <&cam_dvdd_gpio_regulator>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig"; |
| qcom,cam-vreg-min-voltage = <1780000 0 0>; |
| qcom,cam-vreg-max-voltage = <1950000 0 0>; |
| qcom,cam-vreg-op-mode = <105000 0 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active |
| &cam_sensor_rear2_active>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend |
| &cam_sensor_rear2_suspend>; |
| gpios = <&tlmm 34 0>, |
| <&tlmm 48 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_mmss MCLK2_CLK_SRC>, |
| <&clock_mmss MMSS_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| eeprom2: qcom,eeprom@2 { |
| cell-index = <2>; |
| reg = <0x2>; |
| compatible = "qcom,eeprom"; |
| cam_vio-supply = <&pm660_l11>; |
| cam_vana-supply = <&pm660l_bob>; |
| cam_vdig-supply = <&cam_dvdd_gpio_regulator>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig"; |
| qcom,cam-vreg-min-voltage = <1780000 3300000 0>; |
| qcom,cam-vreg-max-voltage = <1950000 3600000 0>; |
| qcom,cam-vreg-op-mode = <105000 80000 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_active |
| &cam_sensor_front_active |
| &cam_actuator_vaf_active>; |
| pinctrl-1 = <&cam_sensor_mclk1_suspend |
| &cam_sensor_front_suspend |
| &cam_actuator_vaf_suspend>; |
| gpios = <&tlmm 33 0>, |
| <&tlmm 47 0>, |
| <&tlmm 44 0>, |
| <&tlmm 50 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-vana = <2>; |
| qcom,gpio-vaf = <3>; |
| qcom,gpio-req-tbl-num = <0 1 2 3>; |
| qcom,gpio-req-tbl-flags = <1 0 0 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2", |
| "CAM_VANA", |
| "CAM_VAF"; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_mmss MCLK1_CLK_SRC>, |
| <&clock_mmss MMSS_CAMSS_MCLK1_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@0 { |
| cell-index = <0>; |
| compatible = "qcom,camera"; |
| reg = <0x0>; |
| qcom,csiphy-sd-index = <0>; |
| qcom,csid-sd-index = <0>; |
| qcom,mount-angle = <90>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,actuator-src = <&actuator0>; |
| qcom,ois-src = <&ois0>; |
| qcom,eeprom-src = <&eeprom0>; |
| cam_vio-supply = <&pm660_l11>; |
| cam_vana-supply = <&cam_avdd_gpio_regulator>; |
| cam_vdig-supply = <&cam_rear_dvdd_gpio_regulator>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig"; |
| qcom,cam-vreg-min-voltage = <1780000 0 0>; |
| qcom,cam-vreg-max-voltage = <1950000 0 0>; |
| qcom,cam-vreg-op-mode = <105000 0 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk0_active |
| &cam_sensor_rear_active>; |
| pinctrl-1 = <&cam_sensor_mclk0_suspend |
| &cam_sensor_rear_suspend>; |
| gpios = <&tlmm 32 0>, |
| <&tlmm 46 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK0", |
| "CAM_RESET0"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <0>; |
| status = "ok"; |
| clocks = <&clock_mmss MCLK0_CLK_SRC>, |
| <&clock_mmss MMSS_CAMSS_MCLK0_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@1 { |
| cell-index = <1>; |
| compatible = "qcom,camera"; |
| reg = <0x1>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <2>; |
| qcom,mount-angle = <90>; |
| qcom,led-flash-src = <&led_flash0>; |
| qcom,actuator-src = <&actuator1>; |
| qcom,eeprom-src = <&eeprom1>; |
| cam_vio-supply = <&pm660_l11>; |
| cam_vana-supply = <&cam_avdd_gpio_regulator>; |
| cam_vdig-supply = <&cam_dvdd_gpio_regulator>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig"; |
| qcom,cam-vreg-min-voltage = <1780000 0 0>; |
| qcom,cam-vreg-max-voltage = <1950000 0 0>; |
| qcom,cam-vreg-op-mode = <105000 0 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk2_active |
| &cam_sensor_rear2_active>; |
| pinctrl-1 = <&cam_sensor_mclk2_suspend |
| &cam_sensor_rear2_suspend>; |
| gpios = <&tlmm 34 0>, |
| <&tlmm 48 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK", |
| "CAM_RESET"; |
| qcom,sensor-position = <0>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_mmss MCLK2_CLK_SRC>, |
| <&clock_mmss MMSS_CAMSS_MCLK2_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@2 { |
| cell-index = <2>; |
| compatible = "qcom,camera"; |
| reg = <0x02>; |
| qcom,csiphy-sd-index = <2>; |
| qcom,csid-sd-index = <2>; |
| qcom,mount-angle = <90>; |
| qcom,actuator-src = <&actuator2>; |
| qcom,eeprom-src = <&eeprom2>; |
| cam_vio-supply = <&pm660_l11>; |
| cam_vana-supply = <&cam_avdd_gpio_regulator>; |
| cam_vdig-supply = <&cam_dvdd_gpio_regulator>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig"; |
| qcom,cam-vreg-min-voltage = <1780000 0 0>; |
| qcom,cam-vreg-max-voltage = <1950000 0 0>; |
| qcom,cam-vreg-op-mode = <105000 0 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk1_active |
| &cam_sensor_front_active>; |
| pinctrl-1 = <&cam_sensor_mclk1_suspend |
| &cam_sensor_front_suspend>; |
| gpios = <&tlmm 33 0>, |
| <&tlmm 47 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK2", |
| "CAM_RESET2"; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| status = "ok"; |
| clocks = <&clock_mmss MCLK1_CLK_SRC>, |
| <&clock_mmss MMSS_CAMSS_MCLK1_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| |
| qcom,camera@3 { |
| cell-index = <3>; |
| compatible = "qcom,camera"; |
| reg = <0x03>; |
| qcom,csiphy-sd-index = <1>; |
| qcom,csid-sd-index = <1>; |
| qcom,mount-angle = <90>; |
| qcom,led-flash-src = <&led_flash1>; |
| qcom,actuator-src = <&actuator2>; |
| qcom,eeprom-src = <&eeprom2>; |
| cam_vio-supply = <&pm660_l11>; |
| cam_vana-supply = <&cam_avdd_gpio_regulator>; |
| cam_vdig-supply = <&cam_dvdd_gpio_regulator>; |
| qcom,cam-vreg-name = "cam_vio", "cam_vana", "cam_vdig"; |
| qcom,cam-vreg-min-voltage = <1780000 0 0>; |
| qcom,cam-vreg-max-voltage = <1950000 0 0>; |
| qcom,cam-vreg-op-mode = <105000 0 0>; |
| qcom,gpio-no-mux = <0>; |
| pinctrl-names = "cam_default", "cam_suspend"; |
| pinctrl-0 = <&cam_sensor_mclk3_active |
| &cam_sensor_front_iris_active>; |
| pinctrl-1 = <&cam_sensor_mclk3_suspend |
| &cam_sensor_front_iris_suspend>; |
| gpios = <&tlmm 35 0>, |
| <&tlmm 52 0>; |
| qcom,gpio-reset = <1>; |
| qcom,gpio-req-tbl-num = <0 1>; |
| qcom,gpio-req-tbl-flags = <1 0>; |
| qcom,gpio-req-tbl-label = "CAMIF_MCLK3", |
| "CAM_RESET3"; |
| qcom,sensor-position = <1>; |
| qcom,sensor-mode = <0>; |
| qcom,cci-master = <1>; |
| clocks = <&clock_mmss MCLK3_CLK_SRC>, |
| <&clock_mmss MMSS_CAMSS_MCLK3_CLK>; |
| clock-names = "cam_src_clk", "cam_clk"; |
| qcom,clock-rates = <24000000 0>; |
| }; |
| }; |
| |
| &pm660l_gpios { |
| cam_sensor_eldo3 { |
| cam_sensor_eldo3_default: cam_sensor_eldo3_default { |
| pins = "gpio3"; |
| function = "normal"; |
| output-high; |
| bias-disable; |
| }; |
| }; |
| cam_sensor_eldo4 { |
| cam_sensor_eldo4_default: cam_sensor_eldo4_default { |
| pins = "gpio4"; |
| function = "normal"; |
| output-low; |
| bias-disable; |
| }; |
| }; |
| }; |
