| # SPDX-License-Identifier: GPL-2.0-only |
| |
| menu "Qualcomm Technologies, Inc. Charger and Fuel Gauge support" |
| |
| config QPNP_PMIC_VOTER |
| tristate "QPNP PMIC Voter library" |
| help |
| Say Y here to enable the Qualcomm Technologies, Inc. PMIC Voter library |
| which is used by several of the QPNP drivers. |
| |
| config QPNP_BATTERY |
| tristate "QPNP Battery library" |
| default m if QPNP_SMB5=m || QPNP_QNOVO5=m |
| default y if QPNP_SMB5=y || QPNP_QNOVO5=y |
| help |
| Say Y here to enable the Qualcomm Technologies, Inc. Battery library |
| which is used by several of the QPNP drivers. |
| |
| config QPNP_SMB2 |
| tristate "SMB2 Battery Charger" |
| depends on MFD_SPMI_PMIC |
| help |
| Say Y to enables support for the SMB2 charging peripheral. |
| The QPNP SMB2 charger driver supports the charger peripheral |
| present in the PMICOBALT chip. |
| The power supply framework is used to communicate battery and |
| usb properties to userspace and other driver consumers such |
| as fuel gauge, USB, and USB-PD. |
| VBUS and VCONN regulators are registered for supporting OTG, |
| and powered Type-C cables respectively. |
| |
| config QPNP_SMB5 |
| tristate "SMB5 Battery Charger" |
| depends on MFD_SPMI_PMIC |
| depends on QPNP_PMIC_VOTER |
| depends on QPNP_REVID |
| help |
| Say Y to enables support for the SMB5 charging peripheral. |
| The QPNP SMB5 charger driver supports the charger peripheral |
| present in the chip. |
| The power supply framework is used to communicate battery and |
| usb properties to userspace and other driver consumers such |
| as fuel gauge, USB, and USB-PD. |
| VBUS and VCONN regulators are registered for supporting OTG, |
| and powered Type-C cables respectively. |
| |
| config QPNP_SMBLITE |
| tristate "SMBLITE Battery Charger" |
| depends on MFD_SPMI_PMIC |
| help |
| Say Y to enables support for the SMBLITE charging peripheral. |
| The QPNP SMBLITE charger driver supports the charger peripheral |
| present in the chip. |
| The power supply framework is used to communicate battery and |
| usb properties to userspace and other driver consumers such |
| as fuel gauge and USB. |
| VBUS regulator is registered for supporting OTG. |
| |
| config SMB138X_CHARGER |
| tristate "SMB138X Battery Charger" |
| depends on MFD_I2C_PMIC |
| help |
| Say Y to include support for SMB138X Battery Charger. |
| SMB1380 is a dual phase 6A battery charger, and SMB1381 is a single |
| phase 5A battery charger. |
| The driver supports charger enable/disable. |
| The driver reports the charger status via the power supply framework. |
| A charger status change triggers an IRQ via the device STAT pin. |
| |
| config SMB1390_CHARGE_PUMP_PSY |
| tristate "SMB1390 power supply framework based driver" |
| depends on MFD_SPMI_PMIC |
| depends on QPNP_PMIC_VOTER |
| depends on QPNP_REVID |
| help |
| Say Y to include support for SMB1390 Charge Pump driver based on |
| power supply framework. |
| SMB1390 is a div2 charge pump capable of delivering 6A charge current |
| with very high efficiency. It can work either as 2s to 1s |
| pre-regulator or as a companion charger when paired with Qualcomm |
| Technologies, Inc.’s family of standalone chargers to enable a high |
| current, low profile Li+ battery charging system. |
| |
| config SMB1351_USB_CHARGER |
| tristate "smb1351 usb charger (with VBUS detection)" |
| depends on I2C |
| help |
| Say Y to enable support for the SMB1351 switching mode based charger. |
| The driver supports charging control (enable/disable) and |
| charge-current limiting. It also provides USB VBUS detection and |
| notification support. The driver controls SMB1351 via I2C and |
| supports device-tree interface. |
| |
| config SMB1355_SLAVE_CHARGER |
| tristate "SMB1355 Slave Battery Charger" |
| depends on MFD_I2C_PMIC |
| depends on QPNP_PMIC_VOTER |
| depends on QPNP_REVID |
| help |
| Say Y to include support for SMB1355 Battery Charger. |
| SMB1355 is a single phase 5A battery charger. |
| The driver supports charger enable/disable. |
| The driver reports the charger status via the power supply framework. |
| A charger status change triggers an IRQ via the device STAT pin. |
| |
| config QPNP_QNOVO5 |
| tristate "QPNP QNOVO5 driver" |
| depends on MFD_SPMI_PMIC |
| depends on QPNP_PMIC_VOTER |
| help |
| Say Y here to enable the Qnovo5 PBS-based pulse charging engine. |
| Qnovo5 driver accepts pulse parameters via sysfs entries and programs |
| the hardware module. It also allows userspace code to read diagnostics |
| of voltage and current measured during certain phases of the pulses. |
| |
| config QPNP_FG_GEN3 |
| tristate "QPNP GEN3 fuel gauge driver" |
| depends on MFD_SPMI_PMIC |
| help |
| Say Y here to enable the GEN3 Fuel Gauge driver. This adds support |
| for battery fuel gauging and state of charge of battery connected to |
| the fuel gauge. The state of charge is reported through a BMS power |
| supply property and also sends uevents when the capacity is updated. |
| |
| config QPNP_FG_GEN4 |
| tristate "QPNP GEN4 fuel gauge driver" |
| depends on MFD_SPMI_PMIC |
| depends on QPNP_PMIC_VOTER |
| depends on QPNP_REVID |
| help |
| Say Y here to enable the GEN4 Fuel Gauge driver. This adds support |
| for battery fuel gauging and state of charge of battery connected to |
| the device that has QTI PMICs like PM8150B. The state of charge is |
| reported through a BMS power supply property and also sends uevents |
| when the capacity is updated. |
| |
| config QPNP_QG |
| tristate "QPNP Qgauge driver" |
| depends on MFD_SPMI_PMIC |
| depends on QPNP_PMIC_VOTER |
| depends on QPNP_REVID |
| help |
| Say Y here to enable the Qualcomm Technologies, Inc. QGauge driver |
| which uses the periodic sampling of the battery voltage and current |
| to determine the battery state-of-charge (SOC) and supports other |
| battery management features. |
| |
| config HL6111R |
| bool "HL6111R driver" |
| depends on I2C && OF |
| select REGMAP_I2C |
| help |
| Say Y here to enable the Halo Microelectronics HL6111R driver. |
| HL6111R is a wireless charging power receiver IC that supports the |
| A4WP wireless charging power delivery standard. It supports up to |
| 15W, and the output voltage can be programmed with variable step |
| sizes. The HL6111R has voltage, current and temperature |
| protection mechanisms, an I2C interface, and a PSNS output. |
| |
| config SMB1398_CHARGER |
| tristate "SMB1398 power supply framework based driver" |
| depends on MFD_I2C_PMIC |
| help |
| Say Y to include the support of SMB1398 Charge driver based on power |
| supply framework. |
| SMB1398 is a combo charger chip which can work in different modes: |
| (1) DIV2 charge pump mode to work as a companion charger to be paired |
| with Qualcomm Technologies, Inc.’s family of standalone chargers; |
| (2) DIV2 and 3-level buck combo mode to regulate the output power from |
| wireless charger receiver and provide the input for downstream |
| chargers. |
| |
| endmenu |
