| #include <dt-bindings/spmi/spmi.h> |
| #include <dt-bindings/interrupt-controller/irq.h> |
| #include <dt-bindings/iio/qcom,spmi-vadc.h> |
| |
| &spmi_bus { |
| #address-cells = <2>; |
| #size-cells = <0>; |
| interrupt-controller; |
| #interrupt-cells = <4>; |
| |
| qcom,pm8150b@2 { |
| compatible = "qcom,spmi-pmic"; |
| reg = <0x2 SPMI_USID>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| pm8150b_revid: qcom,revid@100 { |
| compatible = "qcom,qpnp-revid"; |
| reg = <0x100 0x100>; |
| }; |
| |
| qcom,power-on@800 { |
| compatible = "qcom,qpnp-power-on"; |
| reg = <0x800 0x100>; |
| }; |
| |
| pm8150b_tz: qcom,temp-alarm@2400 { |
| compatible = "qcom,spmi-temp-alarm"; |
| reg = <0x2400 0x100>; |
| interrupts = <0x2 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| io-channels = <&pm8150b_vadc ADC_DIE_TEMP>; |
| io-channel-names = "thermal"; |
| #thermal-sensor-cells = <0>; |
| qcom,temperature-threshold-set = <1>; |
| }; |
| |
| pm8150b_clkdiv: clock-controller@6000 { |
| compatible = "qcom,spmi-clkdiv"; |
| reg = <0x6000 0x100>; |
| #clock-cells = <1>; |
| qcom,num-clkdivs = <1>; |
| clock-output-names = "pm8150b_div_clk1"; |
| clocks = <&clock_rpmh RPMH_CXO_CLK>; |
| clock-names = "xo"; |
| }; |
| |
| pm8150b_pbs1: qcom,pbs@7200 { |
| compatible = "qcom,qpnp-pbs"; |
| reg = <0x7200 0x100>; |
| }; |
| |
| pm8150b_qnovo: qcom,sdam-qnovo@b000 { |
| compatible = "qcom,qpnp-qnovo5"; |
| reg = <0xb000 0x100>; |
| interrupts = <0x2 0xb0 1 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "ptrain-done"; |
| }; |
| |
| pm8150b_gpios: pinctrl@c000 { |
| compatible = "qcom,spmi-gpio"; |
| reg = <0xc000 0xc00>; |
| interrupts = <0x2 0xc0 0x0 IRQ_TYPE_NONE>, |
| <0x2 0xc1 0x0 IRQ_TYPE_NONE>, |
| <0x2 0xc4 0x0 IRQ_TYPE_NONE>, |
| <0x2 0xc5 0x0 IRQ_TYPE_NONE>, |
| <0x2 0xc6 0x0 IRQ_TYPE_NONE>, |
| <0x2 0xc7 0x0 IRQ_TYPE_NONE>, |
| <0x2 0xc8 0x0 IRQ_TYPE_NONE>, |
| <0x2 0xc9 0x0 IRQ_TYPE_NONE>, |
| <0x2 0xcb 0x0 IRQ_TYPE_NONE>; |
| interrupt-names = "pm8150b_gpio1", "pm8150b_gpio2", |
| "pm8150b_gpio5", "pm8150b_gpio6", |
| "pm8150b_gpio7", "pm8150b_gpio8", |
| "pm8150b_gpio9", "pm8150b_gpio10", |
| "pm8150b_gpio12"; |
| gpio-controller; |
| #gpio-cells = <2>; |
| qcom,gpios-disallowed = <3 4 11>; |
| }; |
| |
| pm8150b_charger: qcom,qpnp-smb5 { |
| compatible = "qcom,qpnp-smb5"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| #cooling-cells = <2>; |
| |
| qcom,pmic-revid = <&pm8150b_revid>; |
| |
| qcom,thermal-mitigation |
| = <3000000 1500000 1000000 500000>; |
| |
| qcom,chg-term-src = <1>; |
| qcom,charger-temp-max = <800>; |
| qcom,smb-temp-max = <800>; |
| status = "disabled"; |
| |
| qcom,chgr@1000 { |
| reg = <0x1000 0x100>; |
| interrupts = |
| <0x2 0x10 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x10 0x1 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x10 0x2 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x10 0x3 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x10 0x4 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x10 0x6 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x10 0x7 IRQ_TYPE_EDGE_BOTH>; |
| |
| interrupt-names = "chgr-error", |
| "chg-state-change", |
| "step-chg-state-change", |
| "step-chg-soc-update-fail", |
| "step-chg-soc-update-req", |
| "vph-alarm", |
| "vph-drop-prechg"; |
| }; |
| |
| qcom,dcdc@1100 { |
| reg = <0x1100 0x100>; |
| interrupts = |
| <0x2 0x11 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x11 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x11 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x11 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x11 0x5 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x11 0x6 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x11 0x7 IRQ_TYPE_EDGE_BOTH>; |
| |
| interrupt-names = "otg-fail", |
| "otg-oc-disable-sw", |
| "otg-oc-hiccup", |
| "high-duty-cycle", |
| "input-current-limiting", |
| "concurrent-mode-disable", |
| "switcher-power-ok"; |
| }; |
| |
| qcom,batif@1200 { |
| reg = <0x1200 0x100>; |
| interrupts = |
| <0x2 0x12 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x12 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x12 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x12 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x12 0x5 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x12 0x6 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x12 0x7 IRQ_TYPE_EDGE_BOTH>; |
| |
| interrupt-names = "bat-temp", |
| "bat-ov", |
| "bat-low", |
| "bat-therm-or-id-missing", |
| "bat-terminal-missing", |
| "buck-oc", |
| "vph-ov"; |
| }; |
| |
| qcom,usb@1300 { |
| reg = <0x1300 0x100>; |
| interrupts = |
| <0x2 0x13 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x13 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x13 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x13 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x13 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x13 0x5 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x13 0x6 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x13 0x7 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-names = "usbin-collapse", |
| "usbin-vashdn", |
| "usbin-uv", |
| "usbin-ov", |
| "usbin-plugin", |
| "usbin-revi-change", |
| "usbin-src-change", |
| "usbin-icl-change"; |
| }; |
| |
| qcom,dc@1400 { |
| reg = <0x1400 0x100>; |
| interrupts = |
| <0x2 0x14 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x14 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x14 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x14 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x14 0x5 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x14 0x6 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x14 0x7 IRQ_TYPE_EDGE_BOTH>; |
| |
| interrupt-names = "dcin-vashdn", |
| "dcin-uv", |
| "dcin-ov", |
| "dcin-plugin", |
| "dcin-revi", |
| "dcin-pon", |
| "dcin-en"; |
| }; |
| |
| qcom,typec@1500 { |
| reg = <0x1500 0x100>; |
| interrupts = |
| <0x2 0x15 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x15 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x15 0x2 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x15 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x15 0x4 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x15 0x5 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x15 0x6 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x15 0x7 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-names = "typec-or-rid-detect-change", |
| "typec-vpd-detect", |
| "typec-cc-state-change", |
| "typec-vconn-oc", |
| "typec-vbus-change", |
| "typec-attach-detach", |
| "typec-legacy-cable-detect", |
| "typec-try-snk-src-detect"; |
| }; |
| |
| qcom,misc@1600 { |
| reg = <0x1600 0x100>; |
| interrupts = |
| <0x2 0x16 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x16 0x1 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x16 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x16 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x16 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x16 0x6 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x16 0x7 IRQ_TYPE_EDGE_BOTH>; |
| |
| interrupt-names = "wdog-snarl", |
| "wdog-bark", |
| "aicl-fail", |
| "aicl-done", |
| "smb-en", |
| "temp-change", |
| "temp-change-smb"; |
| }; |
| }; |
| |
| pm8150b_pdphy: qcom,usb-pdphy@1700 { |
| compatible = "qcom,qpnp-pdphy"; |
| reg = <0x1700 0x100>; |
| interrupts = <0x2 0x17 0x0 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x17 0x1 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x17 0x2 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x17 0x3 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x17 0x4 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x17 0x5 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x17 0x6 IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x17 0x7 IRQ_TYPE_EDGE_RISING>; |
| |
| interrupt-names = "sig-tx", |
| "sig-rx", |
| "msg-tx", |
| "msg-rx", |
| "msg-tx-failed", |
| "msg-tx-discarded", |
| "msg-rx-discarded", |
| "fr-swap"; |
| |
| qcom,default-sink-caps = <5000 3000>, /* 5V @ 3A */ |
| <9000 3000>, /* 9V @ 3A */ |
| <12000 2250>; /* 12V @ 2.25A */ |
| }; |
| |
| pm8150b_bcl: bcl@1d00 { |
| compatible = "qcom,bcl-v5"; |
| reg = <0x1d00 0x100>; |
| interrupts = <0x2 0x1d 0x0 IRQ_TYPE_NONE>, |
| <0x2 0x1d 0x1 IRQ_TYPE_NONE>, |
| <0x2 0x1d 0x2 IRQ_TYPE_NONE>; |
| interrupt-names = "bcl-lvl0", |
| "bcl-lvl1", |
| "bcl-lvl2"; |
| #thermal-sensor-cells = <1>; |
| }; |
| |
| bcl_soc:bcl-soc { |
| compatible = "qcom,msm-bcl-soc"; |
| #thermal-sensor-cells = <0>; |
| }; |
| |
| pm8150b_fg: qpnp,fg { |
| compatible = "qcom,fg-gen4"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| qcom,pmic-revid = <&pm8150b_revid>; |
| qcom,pmic-pbs = <&pm8150b_pbs1>; |
| status = "disabled"; |
| |
| qcom,fg-batt-soc@4000 { |
| status = "okay"; |
| reg = <0x4000 0x100>; |
| interrupts = <0x2 0x40 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x40 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x40 0x2 |
| IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x40 0x3 |
| IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x40 0x4 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x40 0x5 |
| IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x40 0x6 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x40 0x7 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "soc-update", |
| "soc-ready", |
| "bsoc-delta", |
| "msoc-delta", |
| "msoc-low", |
| "msoc-empty", |
| "msoc-high", |
| "msoc-full"; |
| }; |
| |
| qcom,fg-batt-info@4100 { |
| status = "okay"; |
| reg = <0x4100 0x100>; |
| interrupts = <0x2 0x41 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x41 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x41 0x3 |
| IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "vbatt-low", |
| "vbatt-pred-delta", |
| "esr-delta"; |
| }; |
| |
| qcom,fg-rradc@4200 { |
| status = "okay"; |
| reg = <0x4200 0x100>; |
| interrupts = <0x2 0x42 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x42 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x42 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x42 0x3 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x42 0x4 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "batt-missing", |
| "batt-id", |
| "batt-temp-delta", |
| "batt-temp-hot", |
| "batt-temp-cold"; |
| }; |
| |
| qcom,fg-memif@4300 { |
| status = "okay"; |
| reg = <0x4300 0x100>; |
| interrupts = <0x2 0x43 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x43 0x1 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x43 0x2 IRQ_TYPE_EDGE_BOTH>, |
| <0x2 0x43 0x3 |
| IRQ_TYPE_EDGE_RISING>, |
| <0x2 0x43 0x4 |
| IRQ_TYPE_EDGE_FALLING>; |
| interrupt-names = "ima-rdy", |
| "ima-xcp", |
| "dma-xcp", |
| "dma-grant", |
| "mem-attn"; |
| }; |
| }; |
| |
| pm8150b_vadc: vadc@3100 { |
| compatible = "qcom,spmi-adc5"; |
| reg = <0x3100 0x100>, <0x3700 0x100>; |
| reg-names = "adc5-usr-base", "adc5-cal-base"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "eoc-int-en-set"; |
| qcom,adc-vdd-reference = <1875>; |
| #io-channel-cells = <1>; |
| io-channel-ranges; |
| |
| /* Channel node */ |
| ref_gnd@0 { |
| reg = <ADC_REF_GND>; |
| label = "ref_gnd"; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| vref_1p25@1 { |
| reg = <ADC_1P25VREF>; |
| label = "vref_1p25"; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| die_temp@2 { |
| reg = <ADC_DIE_TEMP>; |
| label = "die_temp"; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| chg_temp@9 { |
| reg = <ADC_CHG_TEMP>; |
| label = "chg_temp"; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| bat_id@4b { |
| reg = <ADC_BAT_ID_PU2>; |
| label = "bat_id"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| smb1390_therm@e { |
| reg = <ADC_AMUX_THM2>; |
| label = "smb1390_therm"; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| smb1355_therm@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| label = "smb1355_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| }; |
| |
| pm8150b_adc_tm: adc_tm@3500 { |
| compatible = "qcom,adc-tm5"; |
| reg = <0x3500 0x100>; |
| interrupts = <0x2 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| interrupt-names = "thr-int-en"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #thermal-sensor-cells = <1>; |
| qcom,pmic-revid = <&pm8150b_revid>; |
| }; |
| }; |
| |
| qcom,pm8150b@3 { |
| compatible ="qcom,spmi-pmic"; |
| reg = <0x3 SPMI_USID>; |
| #address-cells = <2>; |
| #size-cells = <0>; |
| |
| pm8150b_pwm: qcom,pwms@b100 { |
| compatible = "qcom,pwm-lpg"; |
| reg = <0xb100 0x200>; |
| reg-names = "lpg-base"; |
| #pwm-cells = <2>; |
| qcom,num-lpg-channels = <2>; |
| }; |
| |
| pm8150b_hr_led: qcom,leds@d000 { |
| compatible = "qcom,tri-led"; |
| reg = <0xd000 0x100>; |
| nvmem-names = "pbs_sdam"; |
| nvmem = <&pm8150_sdam_2>; |
| hr_led1 { |
| label = "hr_led1"; |
| pwms = <&pm8150b_pwm 0 1000000>; |
| led-sources = <0>; |
| }; |
| |
| hr_led2 { |
| label = "hr_led2"; |
| pwms = <&pm8150b_pwm 1 1000000>; |
| led-sources = <1>; |
| }; |
| }; |
| |
| pm8150b_haptics: qcom,haptics@c000 { |
| compatible = "qcom,haptics"; |
| reg = <0xc000 0x100>; |
| interrupts = <0x3 0xc0 0x0 IRQ_TYPE_EDGE_BOTH>, |
| <0x3 0xc0 0x1 IRQ_TYPE_EDGE_BOTH>; |
| interrupt-names = "hap-sc-irq", "hap-play-irq"; |
| qcom,actuator-type = "lra"; |
| qcom,vmax-mv = <3600>; |
| qcom,play-rate-us = <6667>; |
| qcom,lra-resonance-sig-shape = "sine"; |
| qcom,lra-auto-resonance-mode = "qwd"; |
| qcom,lra-allow-variable-play-rate; |
| |
| wf_0 { |
| /* CLICK */ |
| qcom,effect-id = <0>; |
| qcom,wf-vmax-mv = <3600>; |
| qcom,wf-pattern = [3e 3e 3e 3e 3e 3e 3e 3e]; |
| qcom,wf-play-rate-us = <6667>; |
| qcom,wf-brake-pattern = [00 00 00 00]; |
| qcom,wf-repeat-count = <1>; |
| qcom,wf-s-repeat-count = <1>; |
| qcom,lra-auto-resonance-disable; |
| }; |
| |
| wf_1 { |
| /* DOUBLE CLICK */ |
| qcom,effect-id = <1>; |
| qcom,wf-vmax-mv = <3600>; |
| qcom,wf-pattern = [3e 3e 3e 3e 3e 3e 3e 3e]; |
| qcom,wf-play-rate-us = <6667>; |
| qcom,wf-brake-pattern = [00 00 00 00]; |
| qcom,wf-repeat-count = <1>; |
| qcom,wf-s-repeat-count = <1>; |
| qcom,lra-auto-resonance-disable; |
| }; |
| |
| wf_2 { |
| /* TICK */ |
| qcom,effect-id = <2>; |
| qcom,wf-vmax-mv = <3600>; |
| qcom,wf-pattern = [3e 3e 3e 3e 3e 3e 3e 3e]; |
| qcom,wf-play-rate-us = <6667>; |
| qcom,wf-brake-pattern = [00 00 00 00]; |
| qcom,wf-repeat-count = <1>; |
| qcom,wf-s-repeat-count = <1>; |
| qcom,lra-auto-resonance-disable; |
| }; |
| |
| wf_3 { |
| /* THUD */ |
| qcom,effect-id = <3>; |
| qcom,wf-vmax-mv = <3600>; |
| qcom,wf-pattern = [3e 3e 3e 3e 3e 3e 3e 3e]; |
| qcom,wf-play-rate-us = <6667>; |
| qcom,wf-brake-pattern = [00 00 00 00]; |
| qcom,wf-repeat-count = <1>; |
| qcom,wf-s-repeat-count = <1>; |
| qcom,lra-auto-resonance-disable; |
| }; |
| |
| wf_4 { |
| /* POP */ |
| qcom,effect-id = <4>; |
| qcom,wf-vmax-mv = <3600>; |
| qcom,wf-pattern = [3e 3e 3e 3e 3e 3e 3e 3e]; |
| qcom,wf-play-rate-us = <6667>; |
| qcom,wf-brake-pattern = [00 00 00 00]; |
| qcom,wf-repeat-count = <1>; |
| qcom,wf-s-repeat-count = <1>; |
| qcom,lra-auto-resonance-disable; |
| }; |
| |
| wf_5 { |
| /* HEAVY CLICK */ |
| qcom,effect-id = <5>; |
| qcom,wf-vmax-mv = <3600>; |
| qcom,wf-pattern = [3e 3e 3e 3e 3e 3e 3e 3e]; |
| qcom,wf-play-rate-us = <6667>; |
| qcom,wf-brake-pattern = [00 00 00 00]; |
| qcom,wf-repeat-count = <1>; |
| qcom,wf-s-repeat-count = <1>; |
| qcom,lra-auto-resonance-disable; |
| }; |
| }; |
| }; |
| }; |
| |
| &thermal_zones { |
| pm8150b_temp_alarm: pm8150b_tz { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-governor = "step_wise"; |
| thermal-sensors = <&pm8150b_tz>; |
| wake-capable-sensor; |
| |
| trips { |
| pm8150b_trip0: trip0 { |
| temperature = <95000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| pm8150b_trip1: trip1 { |
| temperature = <115000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| |
| trip2 { |
| temperature = <145000>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pm8150b-ibat-lvl0 { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "step_wise"; |
| thermal-sensors = <&pm8150b_bcl 0>; |
| wake-capable-sensor; |
| |
| trips { |
| ibat_lvl0:ibat-lvl0 { |
| temperature = <4500>; |
| hysteresis = <200>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pm8150b-ibat-lvl1 { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "step_wise"; |
| thermal-sensors = <&pm8150b_bcl 1>; |
| wake-capable-sensor; |
| |
| trips { |
| ibat_lvl1:ibat-lvl1 { |
| temperature = <5000>; |
| hysteresis = <200>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pm8150b-vbat-lvl0 { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "low_limits_cap"; |
| thermal-sensors = <&pm8150b_bcl 2>; |
| tracks-low; |
| wake-capable-sensor; |
| |
| trips { |
| vbat_lvl0: vbat-lvl0 { |
| temperature = <3000>; |
| hysteresis = <200>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pm8150b-vbat-lvl1 { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "low_limits_cap"; |
| thermal-sensors = <&pm8150b_bcl 3>; |
| tracks-low; |
| wake-capable-sensor; |
| |
| trips { |
| vbat_lvl1:vbat-lvl1 { |
| temperature = <2800>; |
| hysteresis = <200>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pm8150b-vbat-lvl2 { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "low_limits_cap"; |
| thermal-sensors = <&pm8150b_bcl 4>; |
| tracks-low; |
| wake-capable-sensor; |
| |
| trips { |
| vbat_lvl2:vbat-lvl2 { |
| temperature = <2600>; |
| hysteresis = <200>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pm8150b-bcl-lvl0 { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-governor = "step_wise"; |
| thermal-sensors = <&pm8150b_bcl 5>; |
| wake-capable-sensor; |
| |
| trips { |
| b_bcl_lvl0: b-bcl-lvl0 { |
| temperature = <1>; |
| hysteresis = <1>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pm8150b-bcl-lvl1 { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-governor = "step_wise"; |
| thermal-sensors = <&pm8150b_bcl 6>; |
| wake-capable-sensor; |
| |
| trips { |
| b_bcl_lvl1: b-bcl-lvl1 { |
| temperature = <1>; |
| hysteresis = <1>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| pm8150b-bcl-lvl2 { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-governor = "step_wise"; |
| thermal-sensors = <&pm8150b_bcl 7>; |
| wake-capable-sensor; |
| |
| trips { |
| b_bcl_lvl2: b-bcl-lvl2 { |
| temperature = <1>; |
| hysteresis = <1>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| soc { |
| polling-delay-passive = <100>; |
| polling-delay = <0>; |
| thermal-governor = "low_limits_cap"; |
| thermal-sensors = <&bcl_soc>; |
| tracks-low; |
| wake-capable-sensor; |
| |
| trips { |
| soc_trip:soc-trip { |
| temperature = <10>; |
| hysteresis = <0>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |
