| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/input/input.h> |
| |
| #include "kona-pmic-overlay.dtsi" |
| #include "kona-sde-display.dtsi" |
| #include "camera/kona-camera-sensor-mtp.dtsi" |
| #include "kona-audio-overlay.dtsi" |
| #include "kona-thermal-overlay.dtsi" |
| |
| &qupv3_se12_2uart { |
| status = "ok"; |
| }; |
| |
| &pm8150a_amoled { |
| status = "ok"; |
| }; |
| |
| &qupv3_se6_4uart { |
| status = "ok"; |
| }; |
| |
| &dai_mi2s2 { |
| qcom,msm-mi2s-tx-lines = <1>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&tert_mi2s_sck_active &tert_mi2s_ws_active |
| &tert_mi2s_sd0_active>; |
| pinctrl-1 = <&tert_mi2s_sck_sleep &tert_mi2s_ws_sleep |
| &tert_mi2s_sd0_sleep>; |
| }; |
| |
| &qupv3_se1_i2c { |
| status = "ok"; |
| qcom,clk-freq-out = <1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| nq@28 { |
| compatible = "qcom,nq-nci"; |
| reg = <0x28>; |
| qcom,nq-irq = <&tlmm 111 0x00>; |
| qcom,nq-ven = <&tlmm 6 0x00>; |
| qcom,nq-firm = <&tlmm 110 0x00>; |
| qcom,nq-clkreq = <&tlmm 7 0x00>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <111 0>; |
| interrupt-names = "nfc_irq"; |
| pinctrl-names = "nfc_active", "nfc_suspend"; |
| pinctrl-0 = <&nfc_int_active &nfc_enable_active |
| &nfc_clk_req_active>; |
| pinctrl-1 = <&nfc_int_suspend &nfc_enable_suspend |
| &nfc_clk_req_suspend>; |
| }; |
| }; |
| |
| &ufsphy_mem { |
| compatible = "qcom,ufs-phy-qmp-v4"; |
| |
| vdda-phy-supply = <&pm8150_l5>; |
| vdda-phy-always-on; |
| vdda-pll-supply = <&pm8150_l9>; |
| vdda-phy-max-microamp = <89900>; |
| vdda-pll-max-microamp = <18800>; |
| |
| status = "ok"; |
| }; |
| |
| &ufshc_mem { |
| vdd-hba-supply = <&ufs_phy_gdsc>; |
| vdd-hba-fixed-regulator; |
| vcc-supply = <&pm8150_l17>; |
| vcc-voltage-level = <2504000 2950000>; |
| vcc-low-voltage-sup; |
| vccq-supply = <&pm8150_l6>; |
| vccq2-supply = <&pm8150_s4>; |
| vcc-max-microamp = <800000>; |
| vccq-max-microamp = <800000>; |
| vccq2-max-microamp = <800000>; |
| |
| qcom,vddp-ref-clk-supply = <&pm8150_l6>; |
| qcom,vddp-ref-clk-max-microamp = <100>; |
| qcom,vccq-parent-supply = <&pm8150a_s8>; |
| qcom,vccq-parent-max-microamp = <210000>; |
| |
| status = "ok"; |
| }; |
| |
| &soc { |
| gpio_keys { |
| compatible = "gpio-keys"; |
| label = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&key_vol_up_default>; |
| |
| vol_up { |
| label = "volume_up"; |
| gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEUP>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| }; |
| |
| qcom,qbt_handler { |
| compatible = "qcom,qbt-handler"; |
| qcom,ipc-gpio = <&tlmm 23 0>; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&key_home_default>; |
| qcom,finger-detect-gpio = <&pm8150_gpios 1 0>; |
| }; |
| }; |
| |
| &qupv3_se13_i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "ok"; |
| qcom,i2c-touch-active = "st,fts"; |
| |
| st_fts@49 { |
| compatible = "st,fts"; |
| reg = <0x49>; |
| interrupt-parent = <&tlmm>; |
| interrupts = <39 0x2008>; |
| vdd-supply = <&pm8150a_l1>; |
| avdd-supply = <&pm8150_l13>; |
| pinctrl-names = "pmx_ts_active", "pmx_ts_suspend"; |
| pinctrl-0 = <&ts_active>; |
| pinctrl-1 = <&ts_int_suspend &ts_reset_suspend>; |
| st,irq-gpio = <&tlmm 39 0x2008>; |
| st,reset-gpio = <&tlmm 38 0x00>; |
| st,regulator_dvdd = "vdd"; |
| st,regulator_avdd = "avdd"; |
| st,x-flip = <1>; |
| st,y-flip = <1>; |
| panel = <&dsi_sw43404_amoled_cmd &dsi_sw43404_amoled_video |
| &dsi_sw43404_amoled_fhd_plus_cmd>; |
| }; |
| }; |
| |
| &vendor { |
| bluetooth: bt_qca6390 { |
| compatible = "qca,qca6390"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_en_sleep>; |
| qca,bt-reset-gpio = <&tlmm 21 0>; /* BT_EN */ |
| qca,bt-sw-ctrl-gpio = <&tlmm 124 0>; /* SW_CTRL */ |
| qca,bt-vdd-aon-supply = <&pm8150_s6>; |
| qca,bt-vdd-dig-supply = <&pm8009_s2>; |
| qca,bt-vdd-rfa1-supply = <&pm8150_s5>; |
| qca,bt-vdd-rfa2-supply = <&pm8150a_s8>; |
| qca,bt-vdd-asd-supply = <&pm8150_l16>; |
| |
| qca,bt-vdd-aon-voltage-level = <950000 950000>; |
| qca,bt-vdd-dig-voltage-level = <950000 952000>; |
| qca,bt-vdd-rfa1-voltage-level = <1900000 1900000>; |
| qca,bt-vdd-rfa2-voltage-level = <1350000 1350000>; |
| qca,bt-vdd-asd-voltage-level = <3024000 3304000>; |
| |
| qca,bt-vdd-asd-current-level = <10000>; |
| }; |
| |
| kona_mtp_batterydata: qcom,battery-data { |
| qcom,batt-id-range-pct = <15>; |
| #include "fg-gen4-batterydata-alium-3600mah.dtsi" |
| #include "fg-gen4-batterydata-ascent-3450mah.dtsi" |
| }; |
| |
| extcon_usb1: extcon_usb1 { |
| compatible = "linux,extcon-usb-gpio"; |
| vbus-gpio = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>; |
| id-gpio = <&tlmm 91 GPIO_ACTIVE_HIGH>; |
| vbus-out-gpio = <&pm8150_gpios 9 GPIO_ACTIVE_HIGH>; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&usb2_vbus_det_default |
| &usb2_id_det_default |
| &usb2_vbus_boost_default>; |
| }; |
| }; |
| |
| &vreg_hap_boost { |
| status = "ok"; |
| }; |
| |
| &pm8150b_haptics { |
| vdd-supply = <&vreg_hap_boost>; |
| }; |
| |
| &pm8150b_vadc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vph_pwr@83 { |
| reg = <ADC_VPH_PWR>; |
| label = "vph_pwr"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| conn_therm@4f { |
| reg = <ADC_AMUX_THM3_PU2>; |
| label = "conn_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| chg_sbux@99 { |
| reg = <ADC_SBUx>; |
| label = "chg_sbux"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| mid_chg_div6@1e { |
| reg = <ADC_MID_CHG_DIV6>; |
| label = "chg_mid"; |
| qcom,pre-scaling = <1 6>; |
| }; |
| |
| usb_in_i_uv@7 { |
| reg = <ADC_USB_IN_I>; |
| label = "usb_in_i_uv"; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| usb_in_v_div_16@8 { |
| reg = <ADC_USB_IN_V_16>; |
| label = "usb_in_v_div_16"; |
| qcom,pre-scaling = <1 16>; |
| }; |
| }; |
| |
| &pm8150b_charger { |
| status = "ok"; |
| qcom,sec-charger-config = <1>; |
| qcom,auto-recharge-soc = <98>; |
| io-channels = <&pm8150b_vadc ADC_MID_CHG_DIV6>, |
| <&pm8150b_vadc ADC_USB_IN_I>, |
| <&pm8150b_vadc ADC_SBUx>, |
| <&pm8150b_vadc ADC_VPH_PWR>, |
| <&pm8150b_vadc ADC_CHG_TEMP>; |
| io-channel-names = "mid_voltage", |
| "usb_in_current", |
| "sbux_res", |
| "vph_voltage", |
| "chg_temp"; |
| qcom,battery-data = <&kona_mtp_batterydata>; |
| qcom,step-charging-enable; |
| qcom,sw-jeita-enable; |
| qcom,wd-bark-time-secs = <16>; |
| qcom,suspend-input-on-debug-batt; |
| qcom,fcc-stepping-enable; |
| qcom,smb-internal-pull-kohm = <0>; |
| }; |
| |
| &pm8150b_fg { |
| status = "ok"; |
| qcom,battery-data = <&kona_mtp_batterydata>; |
| qcom,hold-soc-while-full; |
| qcom,linearize-soc; |
| qcom,five-pin-battery; |
| qcom,cl-wt-enable; |
| qcom,soc-scale-mode-en; |
| qcom,force-calib-level = <130>; |
| /* ESR fast calibration */ |
| qcom,fg-esr-timer-chg-fast = <0 7>; |
| qcom,fg-esr-timer-dischg-fast = <0 7>; |
| qcom,fg-esr-timer-chg-slow = <0 96>; |
| qcom,fg-esr-timer-dischg-slow = <0 96>; |
| qcom,fg-esr-cal-soc-thresh = <26 230>; |
| qcom,fg-esr-cal-temp-thresh = <10 40>; |
| }; |
| |
| &qupv3_se15_i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| #include "smb1390.dtsi" |
| |
| halo,hl6111r@25 { |
| compatible = "halo,hl6111r"; |
| reg = <0x25>; |
| status = "ok"; |
| }; |
| }; |
| |
| &smb1390 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&smb_stat_default>; |
| status = "ok"; |
| }; |
| |
| &smb1390_charger { |
| io-channels = <&pm8150b_vadc ADC_AMUX_THM2>; |
| io-channel-names = "cp_die_temp"; |
| qcom,parallel-output-mode = <2>; |
| qcom,min-ilim-ua = <750000>; |
| status = "ok"; |
| }; |
| |
| &smb1390_slave { |
| status = "ok"; |
| }; |
| |
| &smb1390_slave_charger { |
| status = "ok"; |
| }; |
| |
| &pm8150_vadc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vph_pwr@83 { |
| reg = <ADC_VPH_PWR>; |
| label = "vph_pwr"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| vcoin@85 { |
| reg = <ADC_VCOIN>; |
| label = "vcoin"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| xo_therm@4c { |
| reg = <ADC_XO_THERM_PU2>; |
| label = "xo_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| skin_therm@4d { |
| reg = <ADC_AMUX_THM1_PU2>; |
| label = "skin_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm1@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| label = "pa_therm1"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| }; |
| |
| &pm8150l_vadc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vph_pwr@83 { |
| reg = <ADC_VPH_PWR>; |
| label = "vph_pwr"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| camera_flash_therm@4d { |
| reg = <ADC_AMUX_THM1_PU2>; |
| label = "camera_flash_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| skin_msm_therm@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| label = "skin_msm_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm2@4f { |
| reg = <ADC_AMUX_THM3_PU2>; |
| label = "pa_therm2"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| }; |
| |
| &pm8150b_adc_tm { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| io-channels = <&pm8150b_vadc ADC_AMUX_THM3_PU2>; |
| |
| conn_therm@4f { |
| reg = <ADC_AMUX_THM3_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| &pm8150_adc_tm { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| io-channels = <&pm8150_vadc ADC_XO_THERM_PU2>, |
| <&pm8150_vadc ADC_AMUX_THM1_PU2>, |
| <&pm8150_vadc ADC_AMUX_THM2_PU2>; |
| |
| xo_therm@4c { |
| reg = <ADC_XO_THERM_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| skin_therm@4d { |
| reg = <ADC_AMUX_THM1_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| pa_therm1@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| &pm8150l_adc_tm { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| camera_flash_therm@4d { |
| reg = <ADC_AMUX_THM1_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| skin_msm_therm@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| pa_therm2@4f { |
| reg = <ADC_AMUX_THM3_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| &spmi_debug_bus { |
| status = "ok"; |
| }; |
| |
| &dsi_sw43404_amoled_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-te-gpio = <&tlmm 66 0>; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>; |
| }; |
| |
| &dsi_sw43404_amoled_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>; |
| }; |
| |
| &dsi_sw43404_amoled_fhd_plus_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-te-gpio = <&tlmm 66 0>; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>; |
| }; |
| |
| &dsi_sim_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_sim_vid { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_sim_dsc_375_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_sim_dsc_10b_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_dual_sim_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_dual_sim_vid { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_dual_sim_dsc_375_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_sim_sec_hd_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,panel-sec-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-sec-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| qcom,platform-sec-reset-gpio = <&tlmm 128 0>; |
| }; |
| |
| &sde_dsi { |
| qcom,dsi-default-panel = <&dsi_sw43404_amoled_cmd>; |
| }; |
| |
| &thermal_zones { |
| conn-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150b_adc_tm ADC_AMUX_THM3_PU2>; |
| wake-capable-sensor; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| xo-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150_adc_tm ADC_XO_THERM_PU2>; |
| wake-capable-sensor; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| skin-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150_adc_tm ADC_AMUX_THM1_PU2>; |
| wake-capable-sensor; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| mmw-pa1-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150_adc_tm ADC_AMUX_THM2_PU2>; |
| wake-capable-sensor; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| camera-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM1_PU2>; |
| wake-capable-sensor; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| skin-msm-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM2_PU2>; |
| wake-capable-sensor; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| mmw-pa2-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM3_PU2>; |
| wake-capable-sensor; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |
| |
| &sdhc_2 { |
| vdd-supply = <&pm8150a_l9>; |
| qcom,vdd-voltage-level = <2950000 2960000>; |
| qcom,vdd-current-level = <200 800000>; |
| |
| vdd-io-supply = <&pm8150a_l6>; |
| qcom,vdd-io-voltage-level = <1808000 2960000>; |
| qcom,vdd-io-current-level = <200 22000>; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &storage_cd>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &storage_cd>; |
| |
| cd-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>; |
| |
| status = "ok"; |
| }; |
| |
| &usb1 { |
| extcon = <&extcon_usb1>; |
| }; |
| |
| &wil6210 { |
| status = "ok"; |
| }; |
