|  | // SPDX-License-Identifier: GPL-2.0-or-later | 
|  | /* | 
|  | * Actions Semiconductor Owl SoC's I2C driver | 
|  | * | 
|  | * Copyright (c) 2014 Actions Semi Inc. | 
|  | * Author: David Liu <liuwei@actions-semi.com> | 
|  | * | 
|  | * Copyright (c) 2018 Linaro Ltd. | 
|  | * Author: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org> | 
|  | */ | 
|  |  | 
|  | #include <linux/clk.h> | 
|  | #include <linux/delay.h> | 
|  | #include <linux/i2c.h> | 
|  | #include <linux/interrupt.h> | 
|  | #include <linux/io.h> | 
|  | #include <linux/iopoll.h> | 
|  | #include <linux/module.h> | 
|  | #include <linux/of.h> | 
|  | #include <linux/platform_device.h> | 
|  |  | 
|  | /* I2C registers */ | 
|  | #define OWL_I2C_REG_CTL		0x0000 | 
|  | #define OWL_I2C_REG_CLKDIV	0x0004 | 
|  | #define OWL_I2C_REG_STAT	0x0008 | 
|  | #define OWL_I2C_REG_ADDR	0x000C | 
|  | #define OWL_I2C_REG_TXDAT	0x0010 | 
|  | #define OWL_I2C_REG_RXDAT	0x0014 | 
|  | #define OWL_I2C_REG_CMD		0x0018 | 
|  | #define OWL_I2C_REG_FIFOCTL	0x001C | 
|  | #define OWL_I2C_REG_FIFOSTAT	0x0020 | 
|  | #define OWL_I2C_REG_DATCNT	0x0024 | 
|  | #define OWL_I2C_REG_RCNT	0x0028 | 
|  |  | 
|  | /* I2Cx_CTL Bit Mask */ | 
|  | #define OWL_I2C_CTL_RB		BIT(1) | 
|  | #define OWL_I2C_CTL_GBCC(x)	(((x) & 0x3) << 2) | 
|  | #define	OWL_I2C_CTL_GBCC_NONE	OWL_I2C_CTL_GBCC(0) | 
|  | #define	OWL_I2C_CTL_GBCC_START	OWL_I2C_CTL_GBCC(1) | 
|  | #define	OWL_I2C_CTL_GBCC_STOP	OWL_I2C_CTL_GBCC(2) | 
|  | #define	OWL_I2C_CTL_GBCC_RSTART	OWL_I2C_CTL_GBCC(3) | 
|  | #define OWL_I2C_CTL_IRQE	BIT(5) | 
|  | #define OWL_I2C_CTL_EN		BIT(7) | 
|  | #define OWL_I2C_CTL_AE		BIT(8) | 
|  | #define OWL_I2C_CTL_SHSM	BIT(10) | 
|  |  | 
|  | #define OWL_I2C_DIV_FACTOR(x)	((x) & 0xff) | 
|  |  | 
|  | /* I2Cx_STAT Bit Mask */ | 
|  | #define OWL_I2C_STAT_RACK	BIT(0) | 
|  | #define OWL_I2C_STAT_BEB	BIT(1) | 
|  | #define OWL_I2C_STAT_IRQP	BIT(2) | 
|  | #define OWL_I2C_STAT_LAB	BIT(3) | 
|  | #define OWL_I2C_STAT_STPD	BIT(4) | 
|  | #define OWL_I2C_STAT_STAD	BIT(5) | 
|  | #define OWL_I2C_STAT_BBB	BIT(6) | 
|  | #define OWL_I2C_STAT_TCB	BIT(7) | 
|  | #define OWL_I2C_STAT_LBST	BIT(8) | 
|  | #define OWL_I2C_STAT_SAMB	BIT(9) | 
|  | #define OWL_I2C_STAT_SRGC	BIT(10) | 
|  |  | 
|  | /* I2Cx_CMD Bit Mask */ | 
|  | #define OWL_I2C_CMD_SBE		BIT(0) | 
|  | #define OWL_I2C_CMD_RBE		BIT(4) | 
|  | #define OWL_I2C_CMD_DE		BIT(8) | 
|  | #define OWL_I2C_CMD_NS		BIT(9) | 
|  | #define OWL_I2C_CMD_SE		BIT(10) | 
|  | #define OWL_I2C_CMD_MSS		BIT(11) | 
|  | #define OWL_I2C_CMD_WRS		BIT(12) | 
|  | #define OWL_I2C_CMD_SECL	BIT(15) | 
|  |  | 
|  | #define OWL_I2C_CMD_AS(x)	(((x) & 0x7) << 1) | 
|  | #define OWL_I2C_CMD_SAS(x)	(((x) & 0x7) << 5) | 
|  |  | 
|  | /* I2Cx_FIFOCTL Bit Mask */ | 
|  | #define OWL_I2C_FIFOCTL_NIB	BIT(0) | 
|  | #define OWL_I2C_FIFOCTL_RFR	BIT(1) | 
|  | #define OWL_I2C_FIFOCTL_TFR	BIT(2) | 
|  |  | 
|  | /* I2Cc_FIFOSTAT Bit Mask */ | 
|  | #define OWL_I2C_FIFOSTAT_CECB	BIT(0) | 
|  | #define OWL_I2C_FIFOSTAT_RNB	BIT(1) | 
|  | #define OWL_I2C_FIFOSTAT_RFE	BIT(2) | 
|  | #define OWL_I2C_FIFOSTAT_TFF	BIT(5) | 
|  | #define OWL_I2C_FIFOSTAT_TFD	GENMASK(23, 16) | 
|  | #define OWL_I2C_FIFOSTAT_RFD	GENMASK(15, 8) | 
|  |  | 
|  | /* I2C bus timeout */ | 
|  | #define OWL_I2C_TIMEOUT_MS	(4 * 1000) | 
|  | #define OWL_I2C_TIMEOUT		msecs_to_jiffies(OWL_I2C_TIMEOUT_MS) | 
|  |  | 
|  | #define OWL_I2C_MAX_RETRIES	50 | 
|  |  | 
|  | struct owl_i2c_dev { | 
|  | struct i2c_adapter	adap; | 
|  | struct i2c_msg		*msg; | 
|  | struct completion	msg_complete; | 
|  | struct clk		*clk; | 
|  | spinlock_t		lock; | 
|  | void __iomem		*base; | 
|  | unsigned long		clk_rate; | 
|  | u32			bus_freq; | 
|  | u32			msg_ptr; | 
|  | int			err; | 
|  | }; | 
|  |  | 
|  | static void owl_i2c_update_reg(void __iomem *reg, unsigned int val, bool state) | 
|  | { | 
|  | unsigned int regval; | 
|  |  | 
|  | regval = readl(reg); | 
|  |  | 
|  | if (state) | 
|  | regval |= val; | 
|  | else | 
|  | regval &= ~val; | 
|  |  | 
|  | writel(regval, reg); | 
|  | } | 
|  |  | 
|  | static void owl_i2c_reset(struct owl_i2c_dev *i2c_dev) | 
|  | { | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL, | 
|  | OWL_I2C_CTL_EN, false); | 
|  | mdelay(1); | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL, | 
|  | OWL_I2C_CTL_EN, true); | 
|  |  | 
|  | /* Clear status registers */ | 
|  | writel(0, i2c_dev->base + OWL_I2C_REG_STAT); | 
|  | } | 
|  |  | 
|  | static int owl_i2c_reset_fifo(struct owl_i2c_dev *i2c_dev) | 
|  | { | 
|  | unsigned int val, timeout = 0; | 
|  |  | 
|  | /* Reset FIFO */ | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOCTL, | 
|  | OWL_I2C_FIFOCTL_RFR | OWL_I2C_FIFOCTL_TFR, | 
|  | true); | 
|  |  | 
|  | /* Wait 50ms for FIFO reset complete */ | 
|  | do { | 
|  | val = readl(i2c_dev->base + OWL_I2C_REG_FIFOCTL); | 
|  | if (!(val & (OWL_I2C_FIFOCTL_RFR | OWL_I2C_FIFOCTL_TFR))) | 
|  | break; | 
|  | usleep_range(500, 1000); | 
|  | } while (timeout++ < OWL_I2C_MAX_RETRIES); | 
|  |  | 
|  | if (timeout > OWL_I2C_MAX_RETRIES) { | 
|  | dev_err(&i2c_dev->adap.dev, "FIFO reset timeout\n"); | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static void owl_i2c_set_freq(struct owl_i2c_dev *i2c_dev) | 
|  | { | 
|  | unsigned int val; | 
|  |  | 
|  | val = DIV_ROUND_UP(i2c_dev->clk_rate, i2c_dev->bus_freq * 16); | 
|  |  | 
|  | /* Set clock divider factor */ | 
|  | writel(OWL_I2C_DIV_FACTOR(val), i2c_dev->base + OWL_I2C_REG_CLKDIV); | 
|  | } | 
|  |  | 
|  | static void owl_i2c_xfer_data(struct owl_i2c_dev *i2c_dev) | 
|  | { | 
|  | struct i2c_msg *msg = i2c_dev->msg; | 
|  | unsigned int stat, fifostat; | 
|  |  | 
|  | i2c_dev->err = 0; | 
|  |  | 
|  | /* Handle NACK from target */ | 
|  | fifostat = readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT); | 
|  | if (fifostat & OWL_I2C_FIFOSTAT_RNB) { | 
|  | i2c_dev->err = -ENXIO; | 
|  | /* Clear NACK error bit by writing "1" */ | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOSTAT, | 
|  | OWL_I2C_FIFOSTAT_RNB, true); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* Handle bus error */ | 
|  | stat = readl(i2c_dev->base + OWL_I2C_REG_STAT); | 
|  | if (stat & OWL_I2C_STAT_BEB) { | 
|  | i2c_dev->err = -EIO; | 
|  | /* Clear BUS error bit by writing "1" */ | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT, | 
|  | OWL_I2C_STAT_BEB, true); | 
|  | return; | 
|  | } | 
|  |  | 
|  | /* Handle FIFO read */ | 
|  | if (msg->flags & I2C_M_RD) { | 
|  | while ((readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) & | 
|  | OWL_I2C_FIFOSTAT_RFE) && i2c_dev->msg_ptr < msg->len) { | 
|  | msg->buf[i2c_dev->msg_ptr++] = readl(i2c_dev->base + | 
|  | OWL_I2C_REG_RXDAT); | 
|  | } | 
|  | } else { | 
|  | /* Handle the remaining bytes which were not sent */ | 
|  | while (!(readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) & | 
|  | OWL_I2C_FIFOSTAT_TFF) && i2c_dev->msg_ptr < msg->len) { | 
|  | writel(msg->buf[i2c_dev->msg_ptr++], | 
|  | i2c_dev->base + OWL_I2C_REG_TXDAT); | 
|  | } | 
|  | } | 
|  | } | 
|  |  | 
|  | static irqreturn_t owl_i2c_interrupt(int irq, void *_dev) | 
|  | { | 
|  | struct owl_i2c_dev *i2c_dev = _dev; | 
|  |  | 
|  | spin_lock(&i2c_dev->lock); | 
|  |  | 
|  | owl_i2c_xfer_data(i2c_dev); | 
|  |  | 
|  | /* Clear pending interrupts */ | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_STAT, | 
|  | OWL_I2C_STAT_IRQP, true); | 
|  |  | 
|  | complete_all(&i2c_dev->msg_complete); | 
|  | spin_unlock(&i2c_dev->lock); | 
|  |  | 
|  | return IRQ_HANDLED; | 
|  | } | 
|  |  | 
|  | static u32 owl_i2c_func(struct i2c_adapter *adap) | 
|  | { | 
|  | return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL; | 
|  | } | 
|  |  | 
|  | static int owl_i2c_check_bus_busy(struct i2c_adapter *adap) | 
|  | { | 
|  | struct owl_i2c_dev *i2c_dev = i2c_get_adapdata(adap); | 
|  | unsigned long timeout; | 
|  |  | 
|  | /* Check for Bus busy */ | 
|  | timeout = jiffies + OWL_I2C_TIMEOUT; | 
|  | while (readl(i2c_dev->base + OWL_I2C_REG_STAT) & OWL_I2C_STAT_BBB) { | 
|  | if (time_after(jiffies, timeout)) { | 
|  | dev_err(&adap->dev, "Bus busy timeout\n"); | 
|  | return -ETIMEDOUT; | 
|  | } | 
|  | } | 
|  |  | 
|  | return 0; | 
|  | } | 
|  |  | 
|  | static int owl_i2c_xfer_common(struct i2c_adapter *adap, struct i2c_msg *msgs, | 
|  | int num, bool atomic) | 
|  | { | 
|  | struct owl_i2c_dev *i2c_dev = i2c_get_adapdata(adap); | 
|  | struct i2c_msg *msg; | 
|  | unsigned long time_left, flags; | 
|  | unsigned int i2c_cmd, val; | 
|  | unsigned int addr; | 
|  | int ret, idx; | 
|  |  | 
|  | spin_lock_irqsave(&i2c_dev->lock, flags); | 
|  |  | 
|  | /* Reset I2C controller */ | 
|  | owl_i2c_reset(i2c_dev); | 
|  |  | 
|  | /* Set bus frequency */ | 
|  | owl_i2c_set_freq(i2c_dev); | 
|  |  | 
|  | /* | 
|  | * Spinlock should be released before calling reset FIFO and | 
|  | * bus busy check since those functions may sleep | 
|  | */ | 
|  | spin_unlock_irqrestore(&i2c_dev->lock, flags); | 
|  |  | 
|  | /* Reset FIFO */ | 
|  | ret = owl_i2c_reset_fifo(i2c_dev); | 
|  | if (ret) | 
|  | goto unlocked_err_exit; | 
|  |  | 
|  | /* Check for bus busy */ | 
|  | ret = owl_i2c_check_bus_busy(adap); | 
|  | if (ret) | 
|  | goto unlocked_err_exit; | 
|  |  | 
|  | spin_lock_irqsave(&i2c_dev->lock, flags); | 
|  |  | 
|  | /* Check for Arbitration lost */ | 
|  | val = readl(i2c_dev->base + OWL_I2C_REG_STAT); | 
|  | if (val & OWL_I2C_STAT_LAB) { | 
|  | val &= ~OWL_I2C_STAT_LAB; | 
|  | writel(val, i2c_dev->base + OWL_I2C_REG_STAT); | 
|  | ret = -EAGAIN; | 
|  | goto err_exit; | 
|  | } | 
|  |  | 
|  | if (!atomic) | 
|  | reinit_completion(&i2c_dev->msg_complete); | 
|  |  | 
|  | /* Enable/disable I2C controller interrupt */ | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL, | 
|  | OWL_I2C_CTL_IRQE, !atomic); | 
|  |  | 
|  | /* | 
|  | * Select: FIFO enable, controller mode, Stop enable, Data count enable, | 
|  | * Send start bit | 
|  | */ | 
|  | i2c_cmd = OWL_I2C_CMD_SECL | OWL_I2C_CMD_MSS | OWL_I2C_CMD_SE | | 
|  | OWL_I2C_CMD_NS | OWL_I2C_CMD_DE | OWL_I2C_CMD_SBE; | 
|  |  | 
|  | /* Handle repeated start condition */ | 
|  | if (num > 1) { | 
|  | /* Set internal address length and enable repeated start */ | 
|  | i2c_cmd |= OWL_I2C_CMD_AS(msgs[0].len + 1) | | 
|  | OWL_I2C_CMD_SAS(1) | OWL_I2C_CMD_RBE; | 
|  |  | 
|  | /* Write target address */ | 
|  | addr = i2c_8bit_addr_from_msg(&msgs[0]); | 
|  | writel(addr, i2c_dev->base + OWL_I2C_REG_TXDAT); | 
|  |  | 
|  | /* Write internal register address */ | 
|  | for (idx = 0; idx < msgs[0].len; idx++) | 
|  | writel(msgs[0].buf[idx], | 
|  | i2c_dev->base + OWL_I2C_REG_TXDAT); | 
|  |  | 
|  | msg = &msgs[1]; | 
|  | } else { | 
|  | /* Set address length */ | 
|  | i2c_cmd |= OWL_I2C_CMD_AS(1); | 
|  | msg = &msgs[0]; | 
|  | } | 
|  |  | 
|  | i2c_dev->msg = msg; | 
|  | i2c_dev->msg_ptr = 0; | 
|  |  | 
|  | /* Set data count for the message */ | 
|  | writel(msg->len, i2c_dev->base + OWL_I2C_REG_DATCNT); | 
|  |  | 
|  | addr = i2c_8bit_addr_from_msg(msg); | 
|  | writel(addr, i2c_dev->base + OWL_I2C_REG_TXDAT); | 
|  |  | 
|  | if (!(msg->flags & I2C_M_RD)) { | 
|  | /* Write data to FIFO */ | 
|  | for (idx = 0; idx < msg->len; idx++) { | 
|  | /* Check for FIFO full */ | 
|  | if (readl(i2c_dev->base + OWL_I2C_REG_FIFOSTAT) & | 
|  | OWL_I2C_FIFOSTAT_TFF) | 
|  | break; | 
|  |  | 
|  | writel(msg->buf[idx], | 
|  | i2c_dev->base + OWL_I2C_REG_TXDAT); | 
|  | } | 
|  |  | 
|  | i2c_dev->msg_ptr = idx; | 
|  | } | 
|  |  | 
|  | /* Ignore the NACK if needed */ | 
|  | if (msg->flags & I2C_M_IGNORE_NAK) | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOCTL, | 
|  | OWL_I2C_FIFOCTL_NIB, true); | 
|  | else | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_FIFOCTL, | 
|  | OWL_I2C_FIFOCTL_NIB, false); | 
|  |  | 
|  | /* Start the transfer */ | 
|  | writel(i2c_cmd, i2c_dev->base + OWL_I2C_REG_CMD); | 
|  |  | 
|  | spin_unlock_irqrestore(&i2c_dev->lock, flags); | 
|  |  | 
|  | if (atomic) { | 
|  | /* Wait for Command Execute Completed or NACK Error bits */ | 
|  | ret = readl_poll_timeout_atomic(i2c_dev->base + OWL_I2C_REG_FIFOSTAT, | 
|  | val, val & (OWL_I2C_FIFOSTAT_CECB | | 
|  | OWL_I2C_FIFOSTAT_RNB), | 
|  | 10, OWL_I2C_TIMEOUT_MS * 1000); | 
|  | } else { | 
|  | time_left = wait_for_completion_timeout(&i2c_dev->msg_complete, | 
|  | adap->timeout); | 
|  | if (!time_left) | 
|  | ret = -ETIMEDOUT; | 
|  | } | 
|  |  | 
|  | spin_lock_irqsave(&i2c_dev->lock, flags); | 
|  |  | 
|  | if (ret) { | 
|  | dev_err(&adap->dev, "Transaction timed out\n"); | 
|  | /* Send stop condition and release the bus */ | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL, | 
|  | OWL_I2C_CTL_GBCC_STOP | OWL_I2C_CTL_RB, | 
|  | true); | 
|  | goto err_exit; | 
|  | } | 
|  |  | 
|  | if (atomic) | 
|  | owl_i2c_xfer_data(i2c_dev); | 
|  |  | 
|  | ret = i2c_dev->err < 0 ? i2c_dev->err : num; | 
|  |  | 
|  | err_exit: | 
|  | spin_unlock_irqrestore(&i2c_dev->lock, flags); | 
|  |  | 
|  | unlocked_err_exit: | 
|  | /* Disable I2C controller */ | 
|  | owl_i2c_update_reg(i2c_dev->base + OWL_I2C_REG_CTL, | 
|  | OWL_I2C_CTL_EN, false); | 
|  |  | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | static int owl_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, | 
|  | int num) | 
|  | { | 
|  | return owl_i2c_xfer_common(adap, msgs, num, false); | 
|  | } | 
|  |  | 
|  | static int owl_i2c_xfer_atomic(struct i2c_adapter *adap, | 
|  | struct i2c_msg *msgs, int num) | 
|  | { | 
|  | return owl_i2c_xfer_common(adap, msgs, num, true); | 
|  | } | 
|  |  | 
|  | static const struct i2c_algorithm owl_i2c_algorithm = { | 
|  | .xfer = owl_i2c_xfer, | 
|  | .xfer_atomic = owl_i2c_xfer_atomic, | 
|  | .functionality = owl_i2c_func, | 
|  | }; | 
|  |  | 
|  | static const struct i2c_adapter_quirks owl_i2c_quirks = { | 
|  | .flags		= I2C_AQ_COMB | I2C_AQ_COMB_WRITE_FIRST, | 
|  | .max_read_len   = 240, | 
|  | .max_write_len  = 240, | 
|  | .max_comb_1st_msg_len = 6, | 
|  | .max_comb_2nd_msg_len = 240, | 
|  | }; | 
|  |  | 
|  | static int owl_i2c_probe(struct platform_device *pdev) | 
|  | { | 
|  | struct device *dev = &pdev->dev; | 
|  | struct owl_i2c_dev *i2c_dev; | 
|  | int ret, irq; | 
|  |  | 
|  | i2c_dev = devm_kzalloc(dev, sizeof(*i2c_dev), GFP_KERNEL); | 
|  | if (!i2c_dev) | 
|  | return -ENOMEM; | 
|  |  | 
|  | i2c_dev->base = devm_platform_ioremap_resource(pdev, 0); | 
|  | if (IS_ERR(i2c_dev->base)) | 
|  | return PTR_ERR(i2c_dev->base); | 
|  |  | 
|  | irq = platform_get_irq(pdev, 0); | 
|  | if (irq < 0) | 
|  | return irq; | 
|  |  | 
|  | if (of_property_read_u32(dev->of_node, "clock-frequency", | 
|  | &i2c_dev->bus_freq)) | 
|  | i2c_dev->bus_freq = I2C_MAX_STANDARD_MODE_FREQ; | 
|  |  | 
|  | /* We support only frequencies of 100k and 400k for now */ | 
|  | if (i2c_dev->bus_freq != I2C_MAX_STANDARD_MODE_FREQ && | 
|  | i2c_dev->bus_freq != I2C_MAX_FAST_MODE_FREQ) { | 
|  | dev_err(dev, "invalid clock-frequency %d\n", i2c_dev->bus_freq); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | i2c_dev->clk = devm_clk_get_enabled(dev, NULL); | 
|  | if (IS_ERR(i2c_dev->clk)) { | 
|  | dev_err(dev, "failed to enable clock\n"); | 
|  | return PTR_ERR(i2c_dev->clk); | 
|  | } | 
|  |  | 
|  | i2c_dev->clk_rate = clk_get_rate(i2c_dev->clk); | 
|  | if (!i2c_dev->clk_rate) { | 
|  | dev_err(dev, "input clock rate should not be zero\n"); | 
|  | return -EINVAL; | 
|  | } | 
|  |  | 
|  | init_completion(&i2c_dev->msg_complete); | 
|  | spin_lock_init(&i2c_dev->lock); | 
|  | i2c_dev->adap.owner = THIS_MODULE; | 
|  | i2c_dev->adap.algo = &owl_i2c_algorithm; | 
|  | i2c_dev->adap.timeout = OWL_I2C_TIMEOUT; | 
|  | i2c_dev->adap.quirks = &owl_i2c_quirks; | 
|  | i2c_dev->adap.dev.parent = dev; | 
|  | i2c_dev->adap.dev.of_node = dev->of_node; | 
|  | snprintf(i2c_dev->adap.name, sizeof(i2c_dev->adap.name), | 
|  | "%s", "OWL I2C adapter"); | 
|  | i2c_set_adapdata(&i2c_dev->adap, i2c_dev); | 
|  |  | 
|  | platform_set_drvdata(pdev, i2c_dev); | 
|  |  | 
|  | ret = devm_request_irq(dev, irq, owl_i2c_interrupt, 0, pdev->name, | 
|  | i2c_dev); | 
|  | if (ret) { | 
|  | dev_err(dev, "failed to request irq %d\n", irq); | 
|  | return ret; | 
|  | } | 
|  |  | 
|  | return i2c_add_adapter(&i2c_dev->adap); | 
|  | } | 
|  |  | 
|  | static const struct of_device_id owl_i2c_of_match[] = { | 
|  | { .compatible = "actions,s500-i2c" }, | 
|  | { .compatible = "actions,s700-i2c" }, | 
|  | { .compatible = "actions,s900-i2c" }, | 
|  | { /* sentinel */ } | 
|  | }; | 
|  | MODULE_DEVICE_TABLE(of, owl_i2c_of_match); | 
|  |  | 
|  | static struct platform_driver owl_i2c_driver = { | 
|  | .probe		= owl_i2c_probe, | 
|  | .driver		= { | 
|  | .name	= "owl-i2c", | 
|  | .of_match_table = owl_i2c_of_match, | 
|  | .probe_type = PROBE_PREFER_ASYNCHRONOUS, | 
|  | }, | 
|  | }; | 
|  | module_platform_driver(owl_i2c_driver); | 
|  |  | 
|  | MODULE_AUTHOR("David Liu <liuwei@actions-semi.com>"); | 
|  | MODULE_AUTHOR("Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>"); | 
|  | MODULE_DESCRIPTION("Actions Semiconductor Owl SoC's I2C driver"); | 
|  | MODULE_LICENSE("GPL"); |