blob: 4d9bcb951d831afa1ef2752568230faa0882d025 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0
#
# Block layer core configuration
#
menuconfig BLOCK
bool "Enable the block layer" if EXPERT
default y
select SBITMAP
select SRCU
help
Provide block layer support for the kernel.
Disable this option to remove the block layer support from the
kernel. This may be useful for embedded devices.
If this option is disabled:
- block device files will become unusable
- some filesystems (such as ext3) will become unavailable.
Also, SCSI character devices and USB storage will be disabled since
they make use of various block layer definitions and facilities.
Say Y here unless you know you really don't want to mount disks and
suchlike.
if BLOCK
config LBDAF
bool "Support for large (2TB+) block devices and files"
depends on !64BIT
default y
help
Enable block devices or files of size 2TB and larger.
This option is required to support the full capacity of large
(2TB+) block devices, including RAID, disk, Network Block Device,
Logical Volume Manager (LVM) and loopback.
This option also enables support for single files larger than
2TB.
The ext4 filesystem requires that this feature be enabled in
order to support filesystems that have the huge_file feature
enabled. Otherwise, it will refuse to mount in the read-write
mode any filesystems that use the huge_file feature, which is
enabled by default by mke2fs.ext4.
The GFS2 filesystem also requires this feature.
If unsure, say Y.
config BLK_SCSI_REQUEST
bool
config BLK_DEV_BSG
bool "Block layer SG support v4"
default y
select BLK_SCSI_REQUEST
help
Saying Y here will enable generic SG (SCSI generic) v4 support
for any block device.
Unlike SG v3 (aka block/scsi_ioctl.c drivers/scsi/sg.c), SG v4
can handle complicated SCSI commands: tagged variable length cdbs
with bidirectional data transfers and generic request/response
protocols (e.g. Task Management Functions and SMP in Serial
Attached SCSI).
This option is required by recent UDEV versions to properly
access device serial numbers, etc.
If unsure, say Y.
config BLK_DEV_BSGLIB
bool "Block layer SG support v4 helper lib"
default n
select BLK_DEV_BSG
select BLK_SCSI_REQUEST
help
Subsystems will normally enable this if needed. Users will not
normally need to manually enable this.
If unsure, say N.
config BLK_DEV_INTEGRITY
bool "Block layer data integrity support"
select CRC_T10DIF if BLK_DEV_INTEGRITY
---help---
Some storage devices allow extra information to be
stored/retrieved to help protect the data. The block layer
data integrity option provides hooks which can be used by
filesystems to ensure better data integrity.
Say yes here if you have a storage device that provides the
T10/SCSI Data Integrity Field or the T13/ATA External Path
Protection. If in doubt, say N.
config BLK_DEV_ZONED
bool "Zoned block device support"
---help---
Block layer zoned block device support. This option enables
support for ZAC/ZBC host-managed and host-aware zoned block devices.
Say yes here if you have a ZAC or ZBC storage device.
config BLK_DEV_THROTTLING
bool "Block layer bio throttling support"
depends on BLK_CGROUP=y
default n
---help---
Block layer bio throttling support. It can be used to limit
the IO rate to a device. IO rate policies are per cgroup and
one needs to mount and use blkio cgroup controller for creating
cgroups and specifying per device IO rate policies.
See Documentation/cgroups/blkio-controller.txt for more information.
config BLK_DEV_THROTTLING_LOW
bool "Block throttling .low limit interface support (EXPERIMENTAL)"
depends on BLK_DEV_THROTTLING
default n
---help---
Add .low limit interface for block throttling. The low limit is a best
effort limit to prioritize cgroups. Depending on the setting, the limit
can be used to protect cgroups in terms of bandwidth/iops and better
utilize disk resource.
Note, this is an experimental interface and could be changed someday.
config BLK_CMDLINE_PARSER
bool "Block device command line partition parser"
default n
---help---
Enabling this option allows you to specify the partition layout from
the kernel boot args. This is typically of use for embedded devices
which don't otherwise have any standardized method for listing the
partitions on a block device.
See Documentation/block/cmdline-partition.txt for more information.
config BLK_WBT
bool "Enable support for block device writeback throttling"
default n
---help---
Enabling this option enables the block layer to throttle buffered
background writeback from the VM, making it more smooth and having
less impact on foreground operations. The throttling is done
dynamically on an algorithm loosely based on CoDel, factoring in
the realtime performance of the disk.
config BLK_WBT_SQ
bool "Single queue writeback throttling"
default n
depends on BLK_WBT
---help---
Enable writeback throttling by default on legacy single queue devices
config BLK_WBT_MQ
bool "Multiqueue writeback throttling"
default y
depends on BLK_WBT
---help---
Enable writeback throttling by default on multiqueue devices.
Multiqueue currently doesn't have support for IO scheduling,
enabling this option is recommended.
config BLK_DEBUG_FS
bool "Block layer debugging information in debugfs"
default y
depends on DEBUG_FS
---help---
Include block layer debugging information in debugfs. This information
is mostly useful for kernel developers, but it doesn't incur any cost
at runtime.
Unless you are building a kernel for a tiny system, you should
say Y here.
config BLK_SED_OPAL
bool "Logic for interfacing with Opal enabled SEDs"
---help---
Builds Logic for interfacing with Opal enabled controllers.
Enabling this option enables users to setup/unlock/lock
Locking ranges for SED devices using the Opal protocol.
config BLK_INLINE_ENCRYPTION
bool "Enable inline encryption support in block layer"
help
Build the blk-crypto subsystem. Enabling this lets the
block layer handle encryption, so users can take
advantage of inline encryption hardware if present.
config BLK_INLINE_ENCRYPTION_FALLBACK
bool "Enable crypto API fallback for blk-crypto"
depends on BLK_INLINE_ENCRYPTION
select CRYPTO
select CRYPTO_BLKCIPHER
help
Enabling this lets the block layer handle inline encryption
by falling back to the kernel crypto API when inline
encryption hardware is not present.
menu "Partition Types"
source "block/partitions/Kconfig"
endmenu
endif # BLOCK
config BLOCK_COMPAT
bool
depends on BLOCK && COMPAT
default y
config BLK_MQ_PCI
bool
depends on BLOCK && PCI
default y
config BLK_MQ_VIRTIO
bool
depends on BLOCK && VIRTIO
default y
config BLK_MQ_RDMA
bool
depends on BLOCK && INFINIBAND
default y
source block/Kconfig.iosched