blob: b486f3f5f6a3264037c07d05d335b1737e8d455e [file] [log] [blame]
* Renesas Electronics Ethernet AVB
This file provides information on what the device node for the Ethernet AVB
interface contains.
Required properties:
- compatible: "renesas,etheravb-r8a7790" if the device is a part of R8A7790 SoC.
"renesas,etheravb-r8a7794" if the device is a part of R8A7794 SoC.
"renesas,etheravb-r8a7795" if the device is a part of R8A7795 SoC.
- reg: offset and length of (1) the register block and (2) the stream buffer.
- interrupts: A list of interrupt-specifiers, one for each entry in
interrupt-names.
If interrupt-names is not present, an interrupt specifier
for a single muxed interrupt.
- phy-mode: see ethernet.txt file in the same directory.
- phy-handle: see ethernet.txt file in the same directory.
- #address-cells: number of address cells for the MDIO bus, must be equal to 1.
- #size-cells: number of size cells on the MDIO bus, must be equal to 0.
- clocks: clock phandle and specifier pair.
- pinctrl-0: phandle, referring to a default pin configuration node.
Optional properties:
- interrupt-parent: the phandle for the interrupt controller that services
interrupts for this device.
- interrupt-names: A list of interrupt names.
For the R8A7795 SoC this property is mandatory;
it should include one entry per channel, named "ch%u",
where %u is the channel number ranging from 0 to 24.
For other SoCs this property is optional; if present
it should contain "mux" for a single muxed interrupt.
- pinctrl-names: pin configuration state name ("default").
- renesas,no-ether-link: boolean, specify when a board does not provide a proper
AVB_LINK signal.
- renesas,ether-link-active-low: boolean, specify when the AVB_LINK signal is
active-low instead of normal active-high.
Example:
ethernet@e6800000 {
compatible = "renesas,etheravb-r8a7795";
reg = <0 0xe6800000 0 0x800>, <0 0xe6a00000 0 0x10000>;
interrupt-parent = <&gic>;
interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 53 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 58 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>,
<GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>;
interrupt-names = "ch0", "ch1", "ch2", "ch3",
"ch4", "ch5", "ch6", "ch7",
"ch8", "ch9", "ch10", "ch11",
"ch12", "ch13", "ch14", "ch15",
"ch16", "ch17", "ch18", "ch19",
"ch20", "ch21", "ch22", "ch23",
"ch24";
clocks = <&mstp8_clks R8A7795_CLK_ETHERAVB>;
power-domains = <&cpg_clocks>;
phy-mode = "rgmii-id";
phy-handle = <&phy0>;
pinctrl-0 = <&ether_pins>;
pinctrl-names = "default";
renesas,no-ether-link;
#address-cells = <1>;
#size-cells = <0>;
phy0: ethernet-phy@0 {
rxc-skew-ps = <900>;
rxdv-skew-ps = <0>;
rxd0-skew-ps = <0>;
rxd1-skew-ps = <0>;
rxd2-skew-ps = <0>;
rxd3-skew-ps = <0>;
txc-skew-ps = <900>;
txen-skew-ps = <0>;
txd0-skew-ps = <0>;
txd1-skew-ps = <0>;
txd2-skew-ps = <0>;
txd3-skew-ps = <0>;
reg = <0>;
interrupt-parent = <&gpio2>;
interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
};
};