| /** @file | |
| This file provides some helper functions which are specific for SD card device. | |
| Copyright (c) 2015 - 2016, Intel Corporation. All rights reserved.<BR> | |
| This program and the accompanying materials | |
| are licensed and made available under the terms and conditions of the BSD License | |
| which accompanies this distribution. The full text of the license may be found at | |
| http://opensource.org/licenses/bsd-license.php | |
| THE PROGRAM IS DISTRIBUTED UNDER THE BSD LICENSE ON AN "AS IS" BASIS, | |
| WITHOUT WARRANTIES OR REPRESENTATIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED. | |
| **/ | |
| #include "SdMmcPciHcDxe.h" | |
| /** | |
| Send command GO_IDLE_STATE to the device to make it go to Idle State. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @retval EFI_SUCCESS The SD device is reset correctly. | |
| @retval Others The device reset fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardReset ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_GO_IDLE_STATE; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeBc; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Send command SEND_IF_COND to the device to inquiry the SD Memory Card interface | |
| condition. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] SupplyVoltage The supplied voltage by the host. | |
| @param[in] CheckPattern The check pattern to be sent to the device. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardVoltageCheck ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT8 SupplyVoltage, | |
| IN UINT8 CheckPattern | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_SEND_IF_COND; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR7; | |
| SdMmcCmdBlk.CommandArgument = (SupplyVoltage << 8) | CheckPattern; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| if (!EFI_ERROR (Status)) { | |
| if (SdMmcStatusBlk.Resp0 != SdMmcCmdBlk.CommandArgument) { | |
| return EFI_DEVICE_ERROR; | |
| } | |
| } | |
| return Status; | |
| } | |
| /** | |
| Send command SDIO_SEND_OP_COND to the device to see whether it is SDIO device. | |
| Refer to SDIO Simplified Spec 3 Section 3.2 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] VoltageWindow The supply voltage window. | |
| @param[in] S18R The boolean to show if it should switch to 1.8v. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdioSendOpCond ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT32 VoltageWindow, | |
| IN BOOLEAN S18R | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| UINT32 Switch; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SDIO_SEND_OP_COND; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR4; | |
| Switch = S18R ? BIT24 : 0; | |
| SdMmcCmdBlk.CommandArgument = (VoltageWindow & 0xFFFFFF) | Switch; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Send command SD_SEND_OP_COND to the device to see whether it is SDIO device. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] Rca The relative device address of addressed device. | |
| @param[in] VoltageWindow The supply voltage window. | |
| @param[in] S18R The boolean to show if it should switch to 1.8v. | |
| @param[in] Xpc The boolean to show if it should provide 0.36w power control. | |
| @param[in] Hcs The boolean to show if it support host capacity info. | |
| @param[out] Ocr The buffer to store returned OCR register value. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSendOpCond ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT16 Rca, | |
| IN UINT32 VoltageWindow, | |
| IN BOOLEAN S18R, | |
| IN BOOLEAN Xpc, | |
| IN BOOLEAN Hcs, | |
| OUT UINT32 *Ocr | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| UINT32 Switch; | |
| UINT32 MaxPower; | |
| UINT32 HostCapacity; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_APP_CMD; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| SdMmcCmdBlk.CommandIndex = SD_SEND_OP_COND; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR3; | |
| Switch = S18R ? BIT24 : 0; | |
| MaxPower = Xpc ? BIT28 : 0; | |
| HostCapacity = Hcs ? BIT30 : 0; | |
| SdMmcCmdBlk.CommandArgument = (VoltageWindow & 0xFFFFFF) | Switch | MaxPower | HostCapacity; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| if (!EFI_ERROR (Status)) { | |
| // | |
| // For details, refer to SD Host Controller Simplified Spec 3.0 Table 2-12. | |
| // | |
| *Ocr = SdMmcStatusBlk.Resp0; | |
| } | |
| return Status; | |
| } | |
| /** | |
| Broadcast command ALL_SEND_CID to the bus to ask all the SD devices to send the | |
| data of their CID registers. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardAllSendCid ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_ALL_SEND_CID; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR2; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Send command SET_RELATIVE_ADDR to the SD device to assign a Relative device | |
| Address (RCA). | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[out] Rca The relative device address to assign. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSetRca ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| OUT UINT16 *Rca | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_SET_RELATIVE_ADDR; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeBcr; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR6; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| if (!EFI_ERROR (Status)) { | |
| *Rca = (UINT16)(SdMmcStatusBlk.Resp0 >> 16); | |
| } | |
| return Status; | |
| } | |
| /** | |
| Send command SEND_CSD to the SD device to get the data of the CSD register. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] Rca The relative device address of selected device. | |
| @param[out] Csd The buffer to store the content of the CSD register. | |
| Note the caller should ignore the lowest byte of this | |
| buffer as the content of this byte is meaningless even | |
| if the operation succeeds. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardGetCsd ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT16 Rca, | |
| OUT SD_CSD *Csd | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_SEND_CSD; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR2; | |
| SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| if (!EFI_ERROR (Status)) { | |
| // | |
| // For details, refer to SD Host Controller Simplified Spec 3.0 Table 2-12. | |
| // | |
| CopyMem (((UINT8*)Csd) + 1, &SdMmcStatusBlk.Resp0, sizeof (SD_CSD) - 1); | |
| } | |
| return Status; | |
| } | |
| /** | |
| Send command SEND_CSD to the SD device to get the data of the CSD register. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] Rca The relative device address of selected device. | |
| @param[out] Scr The buffer to store the content of the SCR register. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardGetScr ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT16 Rca, | |
| OUT SD_SCR *Scr | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_APP_CMD; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| SdMmcCmdBlk.CommandIndex = SD_SEND_SCR; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| Packet.InDataBuffer = Scr; | |
| Packet.InTransferLength = sizeof (SD_SCR); | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Send command SELECT_DESELECT_CARD to the SD device to select/deselect it. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] Rca The relative device address of selected device. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSelect ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT16 Rca | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_SELECT_DESELECT_CARD; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc; | |
| if (Rca != 0) { | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1b; | |
| } | |
| SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Send command VOLTAGE_SWITCH to the SD device to switch the voltage of the device. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardVoltageSwitch ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_VOLTAGE_SWITCH; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| SdMmcCmdBlk.CommandArgument = 0; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Send command SET_BUS_WIDTH to the SD device to set the bus width. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] Rca The relative device address of addressed device. | |
| @param[in] BusWidth The bus width to be set, it could be 1 or 4. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSetBusWidth ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT16 Rca, | |
| IN UINT8 BusWidth | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| UINT8 Value; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_APP_CMD; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| SdMmcCmdBlk.CommandIndex = SD_SET_BUS_WIDTH; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| if (BusWidth == 1) { | |
| Value = 0; | |
| } else if (BusWidth == 4) { | |
| Value = 2; | |
| } else { | |
| return EFI_INVALID_PARAMETER; | |
| } | |
| SdMmcCmdBlk.CommandArgument = Value & 0x3; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Send command SWITCH_FUNC to the SD device to check switchable function or switch card function. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] AccessMode The value for access mode group. | |
| @param[in] CommandSystem The value for command set group. | |
| @param[in] DriveStrength The value for drive length group. | |
| @param[in] PowerLimit The value for power limit group. | |
| @param[in] Mode Switch or check function. | |
| @param[out] SwitchResp The return switch function status. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSwitch ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT8 AccessMode, | |
| IN UINT8 CommandSystem, | |
| IN UINT8 DriveStrength, | |
| IN UINT8 PowerLimit, | |
| IN BOOLEAN Mode, | |
| OUT UINT8 *SwitchResp | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| UINT32 ModeValue; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_SWITCH_FUNC; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| ModeValue = Mode ? BIT31 : 0; | |
| SdMmcCmdBlk.CommandArgument = (AccessMode & 0xF) | ((PowerLimit & 0xF) << 4) | \ | |
| ((DriveStrength & 0xF) << 8) | ((DriveStrength & 0xF) << 12) | \ | |
| ModeValue; | |
| Packet.InDataBuffer = SwitchResp; | |
| Packet.InTransferLength = 64; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Send command SEND_STATUS to the addressed SD device to get its status register. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] Rca The relative device address of addressed device. | |
| @param[out] DevStatus The returned device status. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSendStatus ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT16 Rca, | |
| OUT UINT32 *DevStatus | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_SEND_STATUS; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| SdMmcCmdBlk.CommandArgument = (UINT32)Rca << 16; | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| if (!EFI_ERROR (Status)) { | |
| *DevStatus = SdMmcStatusBlk.Resp0; | |
| } | |
| return Status; | |
| } | |
| /** | |
| Send command SEND_TUNING_BLOCK to the SD device for HS200 optimal sampling point | |
| detection. | |
| It may be sent up to 40 times until the host finishes the tuning procedure. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 for details. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSendTuningBlk ( | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot | |
| ) | |
| { | |
| EFI_SD_MMC_COMMAND_BLOCK SdMmcCmdBlk; | |
| EFI_SD_MMC_STATUS_BLOCK SdMmcStatusBlk; | |
| EFI_SD_MMC_PASS_THRU_COMMAND_PACKET Packet; | |
| EFI_STATUS Status; | |
| UINT8 TuningBlock[64]; | |
| ZeroMem (&SdMmcCmdBlk, sizeof (SdMmcCmdBlk)); | |
| ZeroMem (&SdMmcStatusBlk, sizeof (SdMmcStatusBlk)); | |
| ZeroMem (&Packet, sizeof (Packet)); | |
| Packet.SdMmcCmdBlk = &SdMmcCmdBlk; | |
| Packet.SdMmcStatusBlk = &SdMmcStatusBlk; | |
| Packet.Timeout = SD_MMC_HC_GENERIC_TIMEOUT; | |
| SdMmcCmdBlk.CommandIndex = SD_SEND_TUNING_BLOCK; | |
| SdMmcCmdBlk.CommandType = SdMmcCommandTypeAdtc; | |
| SdMmcCmdBlk.ResponseType = SdMmcResponseTypeR1; | |
| SdMmcCmdBlk.CommandArgument = 0; | |
| Packet.InDataBuffer = TuningBlock; | |
| Packet.InTransferLength = sizeof (TuningBlock); | |
| Status = SdMmcPassThruPassThru (PassThru, Slot, &Packet, NULL); | |
| return Status; | |
| } | |
| /** | |
| Tunning the sampling point of SDR104 or SDR50 bus speed mode. | |
| Command SD_SEND_TUNING_BLOCK may be sent up to 40 times until the host finishes the | |
| tuning procedure. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 and | |
| SD Host Controller Simplified Spec 3.0 section Figure 3-7 for details. | |
| @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardTuningClock ( | |
| IN EFI_PCI_IO_PROTOCOL *PciIo, | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot | |
| ) | |
| { | |
| EFI_STATUS Status; | |
| UINT8 HostCtrl2; | |
| UINT8 Retry; | |
| // | |
| // Notify the host that the sampling clock tuning procedure starts. | |
| // | |
| HostCtrl2 = BIT6; | |
| Status = SdMmcHcOrMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| // | |
| // Ask the device to send a sequence of tuning blocks till the tuning procedure is done. | |
| // | |
| Retry = 0; | |
| do { | |
| Status = SdCardSendTuningBlk (PassThru, Slot); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_ERROR, "SdCardSendTuningBlk: Send tuning block fails with %r\n", Status)); | |
| return Status; | |
| } | |
| Status = SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, TRUE, sizeof (HostCtrl2), &HostCtrl2); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| if ((HostCtrl2 & (BIT6 | BIT7)) == 0) { | |
| break; | |
| } | |
| if ((HostCtrl2 & (BIT6 | BIT7)) == BIT7) { | |
| return EFI_SUCCESS; | |
| } | |
| } while (++Retry < 40); | |
| DEBUG ((EFI_D_ERROR, "SdCardTuningClock: Send tuning block fails at %d times with HostCtrl2 %02x\n", Retry, HostCtrl2)); | |
| // | |
| // Abort the tuning procedure and reset the tuning circuit. | |
| // | |
| HostCtrl2 = (UINT8)~(BIT6 | BIT7); | |
| Status = SdMmcHcAndMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| return EFI_DEVICE_ERROR; | |
| } | |
| /** | |
| Switch the bus width to specified width. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 and | |
| SD Host Controller Simplified Spec 3.0 section Figure 3-7 for details. | |
| @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] Rca The relative device address to be assigned. | |
| @param[in] BusWidth The bus width to be set, it could be 4 or 8. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSwitchBusWidth ( | |
| IN EFI_PCI_IO_PROTOCOL *PciIo, | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT16 Rca, | |
| IN UINT8 BusWidth | |
| ) | |
| { | |
| EFI_STATUS Status; | |
| UINT32 DevStatus; | |
| Status = SdCardSetBusWidth (PassThru, Slot, Rca, BusWidth); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_ERROR, "SdCardSwitchBusWidth: Switch to bus width %d fails with %r\n", BusWidth, Status)); | |
| return Status; | |
| } | |
| Status = SdCardSendStatus (PassThru, Slot, Rca, &DevStatus); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_ERROR, "SdCardSwitchBusWidth: Send status fails with %r\n", Status)); | |
| return Status; | |
| } | |
| // | |
| // Check the switch operation is really successful or not. | |
| // | |
| if ((DevStatus >> 16) != 0) { | |
| DEBUG ((EFI_D_ERROR, "SdCardSwitchBusWidth: The switch operation fails as DevStatus is 0x%08x\n", DevStatus)); | |
| return EFI_DEVICE_ERROR; | |
| } | |
| Status = SdMmcHcSetBusWidth (PciIo, Slot, BusWidth); | |
| return Status; | |
| } | |
| /** | |
| Switch the high speed timing according to request. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 4.7 and | |
| SD Host Controller Simplified Spec 3.0 section Figure 2-29 for details. | |
| @param[in] PciIo A pointer to the EFI_PCI_IO_PROTOCOL instance. | |
| @param[in] PassThru A pointer to the EFI_SD_MMC_PASS_THRU_PROTOCOL instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @param[in] Rca The relative device address to be assigned. | |
| @param[in] S18A The boolean to show if it's a UHS-I SD card. | |
| @retval EFI_SUCCESS The operation is done correctly. | |
| @retval Others The operation fails. | |
| **/ | |
| EFI_STATUS | |
| SdCardSetBusMode ( | |
| IN EFI_PCI_IO_PROTOCOL *PciIo, | |
| IN EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru, | |
| IN UINT8 Slot, | |
| IN UINT16 Rca, | |
| IN BOOLEAN S18A | |
| ) | |
| { | |
| EFI_STATUS Status; | |
| SD_MMC_HC_SLOT_CAP *Capability; | |
| UINT32 ClockFreq; | |
| UINT8 BusWidth; | |
| UINT8 AccessMode; | |
| UINT8 HostCtrl1; | |
| UINT8 HostCtrl2; | |
| UINT8 SwitchResp[64]; | |
| SD_MMC_HC_PRIVATE_DATA *Private; | |
| Private = SD_MMC_HC_PRIVATE_FROM_THIS (PassThru); | |
| Capability = &Private->Capability[Slot]; | |
| Status = SdCardSelect (PassThru, Slot, Rca); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| BusWidth = 4; | |
| Status = SdCardSwitchBusWidth (PciIo, PassThru, Slot, Rca, BusWidth); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| // | |
| // Get the supported bus speed from SWITCH cmd return data group #1. | |
| // | |
| Status = SdCardSwitch (PassThru, Slot, 0xF, 0xF, 0xF, 0xF, FALSE, SwitchResp); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| // | |
| // Calculate supported bus speed/bus width/clock frequency by host and device capability. | |
| // | |
| ClockFreq = 0; | |
| if (S18A && (Capability->Sdr104 != 0) && ((SwitchResp[13] & BIT3) != 0)) { | |
| ClockFreq = 208; | |
| AccessMode = 3; | |
| } else if (S18A && (Capability->Sdr50 != 0) && ((SwitchResp[13] & BIT2) != 0)) { | |
| ClockFreq = 100; | |
| AccessMode = 2; | |
| } else if (S18A && (Capability->Ddr50 != 0) && ((SwitchResp[13] & BIT4) != 0)) { | |
| ClockFreq = 50; | |
| AccessMode = 4; | |
| } else if ((SwitchResp[13] & BIT1) != 0) { | |
| ClockFreq = 50; | |
| AccessMode = 1; | |
| } else { | |
| ClockFreq = 25; | |
| AccessMode = 0; | |
| } | |
| Status = SdCardSwitch (PassThru, Slot, AccessMode, 0xF, 0xF, 0xF, TRUE, SwitchResp); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| if ((SwitchResp[16] & 0xF) != AccessMode) { | |
| DEBUG ((EFI_D_ERROR, "SdCardSetBusMode: Switch to AccessMode %d ClockFreq %d BusWidth %d fails! The Switch response is 0x%1x\n", AccessMode, ClockFreq, BusWidth, SwitchResp[16] & 0xF)); | |
| return EFI_DEVICE_ERROR; | |
| } | |
| DEBUG ((EFI_D_INFO, "SdCardSetBusMode: Switch to AccessMode %d ClockFreq %d BusWidth %d\n", AccessMode, ClockFreq, BusWidth)); | |
| // | |
| // Set to Hight Speed timing | |
| // | |
| if (AccessMode == 1) { | |
| HostCtrl1 = BIT2; | |
| Status = SdMmcHcOrMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL1, sizeof (HostCtrl1), &HostCtrl1); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| } | |
| HostCtrl2 = (UINT8)~0x7; | |
| Status = SdMmcHcAndMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| HostCtrl2 = AccessMode; | |
| Status = SdMmcHcOrMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| Status = SdMmcHcClockSupply (PciIo, Slot, ClockFreq * 1000, *Capability); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| if ((AccessMode == 3) || ((AccessMode == 2) && (Capability->TuningSDR50 != 0))) { | |
| Status = SdCardTuningClock (PciIo, PassThru, Slot); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| } | |
| return Status; | |
| } | |
| /** | |
| Execute SD device identification procedure. | |
| Refer to SD Physical Layer Simplified Spec 4.1 Section 3.6 for details. | |
| @param[in] Private A pointer to the SD_MMC_HC_PRIVATE_DATA instance. | |
| @param[in] Slot The slot number of the SD card to send the command to. | |
| @retval EFI_SUCCESS There is a SD card. | |
| @retval Others There is not a SD card. | |
| **/ | |
| EFI_STATUS | |
| SdCardIdentification ( | |
| IN SD_MMC_HC_PRIVATE_DATA *Private, | |
| IN UINT8 Slot | |
| ) | |
| { | |
| EFI_STATUS Status; | |
| EFI_PCI_IO_PROTOCOL *PciIo; | |
| EFI_SD_MMC_PASS_THRU_PROTOCOL *PassThru; | |
| UINT32 Ocr; | |
| UINT16 Rca; | |
| BOOLEAN Xpc; | |
| BOOLEAN S18r; | |
| UINT64 MaxCurrent; | |
| UINT16 ControllerVer; | |
| UINT8 PowerCtrl; | |
| UINT32 PresentState; | |
| UINT8 HostCtrl2; | |
| PciIo = Private->PciIo; | |
| PassThru = &Private->PassThru; | |
| // | |
| // 1. Send Cmd0 to the device | |
| // | |
| Status = SdCardReset (PassThru, Slot); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_INFO, "SdCardIdentification: Executing Cmd0 fails with %r\n", Status)); | |
| return Status; | |
| } | |
| // | |
| // 2. Send Cmd8 to the device | |
| // | |
| Status = SdCardVoltageCheck (PassThru, Slot, 0x1, 0xFF); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_INFO, "SdCardIdentification: Executing Cmd8 fails with %r\n", Status)); | |
| return Status; | |
| } | |
| // | |
| // 3. Send SDIO Cmd5 to the device to the SDIO device OCR register. | |
| // | |
| Status = SdioSendOpCond (PassThru, Slot, 0, FALSE); | |
| if (!EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_INFO, "SdCardIdentification: Found SDIO device, ignore it as we don't support\n")); | |
| return EFI_DEVICE_ERROR; | |
| } | |
| // | |
| // 4. Send Acmd41 with voltage window 0 to the device | |
| // | |
| Status = SdCardSendOpCond (PassThru, Slot, 0, 0, FALSE, FALSE, FALSE, &Ocr); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_INFO, "SdCardIdentification: Executing SdCardSendOpCond fails with %r\n", Status)); | |
| return EFI_DEVICE_ERROR; | |
| } | |
| if (Private->Capability[Slot].Voltage33 != 0) { | |
| // | |
| // Support 3.3V | |
| // | |
| MaxCurrent = ((UINT32)Private->MaxCurrent[Slot] & 0xFF) * 4; | |
| } else if (Private->Capability[Slot].Voltage30 != 0) { | |
| // | |
| // Support 3.0V | |
| // | |
| MaxCurrent = (((UINT32)Private->MaxCurrent[Slot] >> 8) & 0xFF) * 4; | |
| } else if (Private->Capability[Slot].Voltage18 != 0) { | |
| // | |
| // Support 1.8V | |
| // | |
| MaxCurrent = (((UINT32)Private->MaxCurrent[Slot] >> 16) & 0xFF) * 4; | |
| } else { | |
| ASSERT (FALSE); | |
| return EFI_DEVICE_ERROR; | |
| } | |
| if (MaxCurrent >= 150) { | |
| Xpc = TRUE; | |
| } else { | |
| Xpc = FALSE; | |
| } | |
| Status = SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_CTRL_VER, TRUE, sizeof (ControllerVer), &ControllerVer); | |
| if (EFI_ERROR (Status)) { | |
| return Status; | |
| } | |
| if ((ControllerVer & 0xFF) == 2) { | |
| S18r = TRUE; | |
| } else if (((ControllerVer & 0xFF) == 0) || ((ControllerVer & 0xFF) == 1)) { | |
| S18r = FALSE; | |
| } else { | |
| ASSERT (FALSE); | |
| return EFI_UNSUPPORTED; | |
| } | |
| // | |
| // 5. Repeatly send Acmd41 with supply voltage window to the device. | |
| // Note here we only support the cards complied with SD physical | |
| // layer simplified spec version 2.0 and version 3.0 and above. | |
| // | |
| do { | |
| Status = SdCardSendOpCond (PassThru, Slot, 0, Ocr, S18r, Xpc, TRUE, &Ocr); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_ERROR, "SdCardIdentification: SdCardSendOpCond fails with %r Ocr %x, S18r %x, Xpc %x\n", Status, Ocr, S18r, Xpc)); | |
| return EFI_DEVICE_ERROR; | |
| } | |
| } while ((Ocr & BIT31) == 0); | |
| // | |
| // 6. If the S18A bit is set and the Host Controller supports 1.8V signaling | |
| // (One of support bits is set to 1: SDR50, SDR104 or DDR50 in the | |
| // Capabilities register), switch its voltage to 1.8V. | |
| // | |
| if ((Private->Capability[Slot].Sdr50 != 0 || | |
| Private->Capability[Slot].Sdr104 != 0 || | |
| Private->Capability[Slot].Ddr50 != 0) && | |
| ((Ocr & BIT24) != 0)) { | |
| Status = SdCardVoltageSwitch (PassThru, Slot); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_ERROR, "SdCardIdentification: Executing SdCardVoltageSwitch fails with %r\n", Status)); | |
| Status = EFI_DEVICE_ERROR; | |
| goto Error; | |
| } else { | |
| Status = SdMmcHcStopClock (PciIo, Slot); | |
| if (EFI_ERROR (Status)) { | |
| Status = EFI_DEVICE_ERROR; | |
| goto Error; | |
| } | |
| SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_PRESENT_STATE, TRUE, sizeof (PresentState), &PresentState); | |
| if (((PresentState >> 20) & 0xF) != 0) { | |
| DEBUG ((EFI_D_ERROR, "SdCardIdentification: SwitchVoltage fails with PresentState = 0x%x\n", PresentState)); | |
| Status = EFI_DEVICE_ERROR; | |
| goto Error; | |
| } | |
| HostCtrl2 = BIT3; | |
| SdMmcHcOrMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, sizeof (HostCtrl2), &HostCtrl2); | |
| gBS->Stall (5000); | |
| SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_HOST_CTRL2, TRUE, sizeof (HostCtrl2), &HostCtrl2); | |
| if ((HostCtrl2 & BIT3) == 0) { | |
| DEBUG ((EFI_D_ERROR, "SdCardIdentification: SwitchVoltage fails with HostCtrl2 = 0x%x\n", HostCtrl2)); | |
| Status = EFI_DEVICE_ERROR; | |
| goto Error; | |
| } | |
| SdMmcHcInitClockFreq (PciIo, Slot, Private->Capability[Slot]); | |
| gBS->Stall (1000); | |
| SdMmcHcRwMmio (PciIo, Slot, SD_MMC_HC_PRESENT_STATE, TRUE, sizeof (PresentState), &PresentState); | |
| if (((PresentState >> 20) & 0xF) != 0xF) { | |
| DEBUG ((EFI_D_ERROR, "SdCardIdentification: SwitchVoltage fails with PresentState = 0x%x, It should be 0xF\n", PresentState)); | |
| Status = EFI_DEVICE_ERROR; | |
| goto Error; | |
| } | |
| } | |
| DEBUG ((EFI_D_INFO, "SdCardIdentification: Switch to 1.8v signal voltage success\n")); | |
| } | |
| Status = SdCardAllSendCid (PassThru, Slot); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_ERROR, "SdCardIdentification: Executing SdCardAllSendCid fails with %r\n", Status)); | |
| return Status; | |
| } | |
| Status = SdCardSetRca (PassThru, Slot, &Rca); | |
| if (EFI_ERROR (Status)) { | |
| DEBUG ((EFI_D_ERROR, "SdCardIdentification: Executing SdCardSetRca fails with %r\n", Status)); | |
| return Status; | |
| } | |
| // | |
| // Enter Data Tranfer Mode. | |
| // | |
| DEBUG ((EFI_D_INFO, "SdCardIdentification: Found a SD device at slot [%d]\n", Slot)); | |
| Private->Slot[Slot].CardType = SdCardType; | |
| Status = SdCardSetBusMode (PciIo, PassThru, Slot, Rca, ((Ocr & BIT24) != 0)); | |
| return Status; | |
| Error: | |
| // | |
| // Set SD Bus Power = 0 | |
| // | |
| PowerCtrl = (UINT8)~BIT0; | |
| Status = SdMmcHcAndMmio (PciIo, Slot, SD_MMC_HC_POWER_CTRL, sizeof (PowerCtrl), &PowerCtrl); | |
| return EFI_DEVICE_ERROR; | |
| } | |