| ## This file is used by NFC NXP NCI HAL(external/libnfc-nci/halimpl/pn547) |
| ## and NFC Service Java Native Interface Extensions (packages/apps/Nfc/nci/jni/extns/pn547) |
| ############################################################################### |
| # Application options |
| # Logging Levels |
| # NXPLOG_DEFAULT_LOGLEVEL 0x01 |
| # ANDROID_LOG_DEBUG 0x03 |
| # ANDROID_LOG_WARN 0x02 |
| # ANDROID_LOG_ERROR 0x01 |
| # ANDROID_LOG_SILENT 0x00 |
| NXPLOG_EXTNS_LOGLEVEL=0x01 |
| NXPLOG_NCIHAL_LOGLEVEL=0x01 |
| NXPLOG_NCIX_LOGLEVEL=0x01 |
| NXPLOG_NCIR_LOGLEVEL=0x01 |
| NXPLOG_FWDNLD_LOGLEVEL=0x01 |
| NXPLOG_TML_LOGLEVEL=0x01 |
| NFC_DEBUG_ENABLED=0x00 |
| |
| ############################################################################### |
| # Nfc Device Node name |
| NXP_NFC_DEV_NODE="/dev/nq-nci" |
| |
| ############################################################################### |
| # Extension for Mifare reader enable |
| MIFARE_READER_ENABLE=0x01 |
| |
| ############################################################################### |
| # Firmware file type |
| #.so file 0x01 |
| #.bin file 0x02 |
| NXP_FW_TYPE=0x02 |
| |
| ############################################################################### |
| # System clock source selection configuration |
| #define CLK_SRC_XTAL 1 |
| #define CLK_SRC_PLL 2 |
| NXP_SYS_CLK_SRC_SEL=0x01 |
| |
| ############################################################################### |
| # System clock frequency selection configuration |
| #define CLK_FREQ_13MHZ 1 |
| #define CLK_FREQ_19_2MHZ 2 |
| #define CLK_FREQ_24MHZ 3 |
| #define CLK_FREQ_26MHZ 4 |
| #define CLK_FREQ_38_4MHZ 5 |
| #define CLK_FREQ_52MHZ 6 |
| NXP_SYS_CLK_FREQ_SEL=0x00 |
| |
| ############################################################################### |
| # The timeout value to be used for clock request acknowledgment |
| # min value = 0x01 to max = 0x06 |
| NXP_SYS_CLOCK_TO_CFG=0x01 |
| |
| ############################################################################### |
| # NXP proprietary settings |
| NXP_ACT_PROP_EXTN={2F, 02, 00} |
| |
| ############################################################################### |
| # NFC forum profile settings |
| NXP_NFC_PROFILE_EXTN={20, 02, 05, 01, A0, 44, 01, 00} |
| |
| ############################################################################### |
| # NXP TVDD configurations settings |
| # Allow NFCC to configure External TVDD, two configurations (1 and 2) supported, |
| # out of them only one can be configured at a time. |
| NXP_EXT_TVDD_CFG=0x02 |
| |
| ############################################################################### |
| #config1:SLALM, 3.3V for both RM and CM |
| NXP_EXT_TVDD_CFG_1={20, 02, 0F, 01, A0, 0E, 0B, 31, 01, 01, 31, 00, 00, 00, 01, 00, D0, 0C} |
| |
| ############################################################################### |
| #config2: use DCDC in CE, use Tx_Pwr_Req, set CFG2 mode, SLALM, |
| #monitoring 5V from DCDC, 3.3V for both RM and CM, DCDCWaitTime=4.2ms |
| NXP_EXT_TVDD_CFG_2={20, 02, 0F, 01, A0, 0E, 0B, 11, 01, C2, 82, 00, BA, 1E, 14, 00, D0, 0C} |
| |
| ############################################################################### |
| # NXP RF configuration ALM/PLM settings |
| # This section needs to be updated with the correct values based on the platform |
| NXP_RF_CONF_BLK_1={ |
| 20, 02, 19, 03, |
| A0, 0D, 03, 24, 03, 80, |
| A0, 0D, 06, 08, 37, 08, 76, 00, 00, |
| A0, 0D, 06, 08, 42, 00, 02, F2, F2 |
| } |
| |
| ############################################################################### |
| # NXP RF configuration ALM/PLM settings |
| # This section needs to be updated with the correct values based on the platform |
| NXP_RF_CONF_BLK_2={ |
| 20, 02, 10, 01, A0, AF, 0C, 83, 42, B2, 80, 00, 83, 08, B2, 80, 00, 77, 08 |
| } |
| |
| ############################################################################### |
| # NXP RF configuration ALM/PLM settings |
| # This section needs to be updated with the correct values based on the platform |
| NXP_RF_CONF_BLK_3={ |
| 20, 02, 98, 01, A0, 34, 94, 23, 04, 18, 35, 00, 00, 4B, 00, 00, 71, 00, 00, |
| 71, 00, 00, 96, 00, 00, BC, 00, 00, BC, 00, 00, E1, 00, 00, 07, 01, 00, 07, |
| 01, 00, 2C, 01, 00, 2C, 01, 00, 52, 01, 00, 52, 01, 00, 77, 01, 00, 77, 01, |
| 00, C2, 01, 00, C2, 01, 00, 0D, 02, 00, 0D, 02, 00, 58, 02, 00, 58, 02, 00, |
| EE, 02, 00, EE, 02, 00, 18, BC, 00, 00, BC, 00, 00, BC, 00, 00, BC, 00, 00, |
| E1, 00, 00, E1, 00, 00, 2C, 01, 00, 2C, 01, 00, 2C, 01, 00, 2C, 01, 00, 2C, |
| 01, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, DC, 05, |
| 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, DC, 05, 00, |
| DC, 05, 00 |
| } |
| |
| ############################################################################### |
| # NXP RF configuration ALM/PLM settings |
| # This section needs to be updated with the correct values based on the platform |
| NXP_RF_CONF_BLK_4={ |
| 20, 02, A4, 01, A0, A9, A0, 00, C1, 00, 0A, 01, 80, 41, 0A, 02, 81, 83, 0A, |
| 03, C0, 42, 06, 04, 80, 46, 06, 05, C3, 01, 03, 06, C2, 05, 03, 07, C2, 4A, |
| 03, 07, 81, 01, 01, 08, C3, 8B, 03, 08, C3, 05, 01, 09, C3, 92, 03, 09, C6, |
| 84, 01, 0A, C4, CC, 03, 0A, C6, 89, 01, 0B, C5, D4, 03, 0B, C7, 92, 01, 0C, |
| 44, 00, 03, 0C, C7, C6, 01, 0D, 42, 04, 03, 0D, C9, CE, 01, 0E, 42, 48, 03, |
| 0E, 03, 00, 01, 0F, 43, 50, 03, 0F, 43, 04, 01, 10, 43, 91, 03, 10, 45, 0A, |
| 01, 11, 44, 95, 03, 11, 46, 11, 01, 12, 46, 8E, 01, 13, 47, C5, 01, 14, 48, |
| CC, 01, 15, 4B, D4, 01, 16, 4E, D7, 01, 17, 45, A2, 01, 18, 46, A6, 01, 19, |
| 46, AE, 01, 1A, 47, B4, 01, 1B, 48, EA, 01, 1C, 49, F0, 01 |
| } |
| |
| ############################################################################### |
| # NXP RF configuration ALM/PLM settings |
| # This section needs to be updated with the correct values based on the platform |
| NXP_RF_CONF_BLK_5={ |
| 20, 02, 5B, 01, A0, 0B, 57, ED, 0D, 90, 3F, 0F, 4E, 00, 53, 95, 00, 00, 53, |
| 9F, 00, 00, 6B, 9F, 00, 00, 78, 9F, 00, 00, 7A, 9F, 00, 00, 86, 9F, 00, 00, |
| 89, 9F, 00, 00, 95, 9F, 00, 00, 9A, 9F, 00, 00, A4, 9F, 00, 00, A6, 9F, 00, |
| 00, B3, 9F, 00, 00, B5, 9F, 00, 00, C1, 9F, 00, 00, C4, 1F, 00, 00, D0, 1F, |
| 00, 00, DA, 1F, 00, 00, E1, 1F, 00, 00, EE, 1F, 00, 00, FA, 1F, 00, 00 |
| } |
| |
| ############################################################################### |
| # NXP RF configuration ALM/PLM settings |
| # This section needs to be updated with the correct values based on the platform |
| NXP_RF_CONF_BLK_6={ |
| 20, 02, 0C, 01, A0, 18, 08, 0C, 00, 54, 00, F4, FF, F9, FF |
| } |
| |
| |
| ############################################################################### |
| # Core configuration extensions |
| # It includes |
| # Wired mode settings A0ED, A0EE |
| # Tag Detector A040, A041, A043 |
| # Low Power mode A007 |
| # Clock settings A002, A003 |
| # PbF settings A008 |
| # Clock timeout settings A004 |
| # eSE (SVDD) PWR REQ settings A0F2 |
| # Window size A0D8 |
| # DWP Speed A0D5 |
| # How eSE connected to PN553 A012 |
| # UICC2 bit rate A0D1 |
| # SWP1A interface A0D4 |
| # DWP intf behavior config, SVDD Load activated by default if set to 0x31 A037 |
| # SPI CL Sync enable A098 |
| NXP_CORE_CONF_EXTN={20, 02, 5B, 13, |
| A0, EC, 01, 01, |
| A0, ED, 01, 01, |
| A0, 5E, 01, 01, |
| A0, 12, 01, 02, |
| A0, 40, 01, 01, |
| A0, 41, 01, 02, |
| A0, 43, 01, 50, |
| A0, D1, 01, 02, |
| A0, D4, 01, 00, |
| A0, 37, 01, 35, |
| A0, D8, 01, 02, |
| A0, D5, 01, 0A, |
| A0, 98, 01, 03, |
| A0, 9C, 02, 00, 00, |
| A0, AA, 04, F1, 03, 2D, 01, |
| A0, 38, 04, 14, 0B, 0B, 00, |
| A0, 3A, 08, 0A, 00, 0A, 00, 0A, 00, 0A, 00, |
| A0, B2, 01, 19, |
| A0, 91, 01, 00 |
| } |
| |
| ############################################################################### |
| # Core configuration rf field filter settings to enable set to 01 to disable set |
| # to 00 last bit |
| NXP_CORE_RF_FIELD={ 20, 02, 05, 01, A0, 62, 01, 00 } |
| |
| ############################################################################### |
| # To enable i2c fragmentation set i2c fragmentation enable 0x01 to disable set |
| # to 0x00 |
| NXP_I2C_FRAGMENTATION_ENABLED=0x00 |
| |
| ############################################################################### |
| # Core configuration settings |
| NXP_CORE_CONF={ 20, 02, 2D, 0F, |
| 85, 01, 01, |
| 28, 01, 00, |
| 21, 01, 00, |
| 30, 01, 08, |
| 31, 01, 03, |
| 32, 01, 60, |
| 38, 01, 01, |
| 33, 00, |
| 54, 01, 06, |
| 50, 01, 02, |
| 5B, 01, 00, |
| 80, 01, 01, |
| 81, 01, 01, |
| 82, 01, 0E, |
| 18, 01, 01 |
| } |
| |
| ############################################################################### |
| #Enable SWP full power mode when phone is power off |
| NXP_SWP_FULL_PWR_ON=0x00 |
| |
| ############################################################################### |
| #Set the default Felica T3T System Code OffHost route Location : |
| #This settings will be used when application does not set this parameter |
| # host 0x00 |
| # eSE 0x01 |
| # UICC 0x02 |
| # UICC2 0x03 |
| DEFAULT_SYS_CODE_ROUTE=0xC0 |
| |
| ############################################################################### |
| # AID Matching platform options |
| # AID_MATCHING_L 0x01 |
| # AID_MATCHING_K 0x02 |
| AID_MATCHING_PLATFORM=0x01 |
| |
| ############################################################################### |
| #CHINA_TIANJIN_RF_SETTING |
| #Enable 0x01 |
| #Disable 0x00 |
| NXP_CHINA_TIANJIN_RF_ENABLED=0x01 |
| |
| ############################################################################### |
| #SWP_SWITCH_TIMEOUT_SETTING |
| # Allowed range of swp timeout setting is 0x00 to 0x3C [0 - 60]. |
| # Timeout in milliseconds, for example |
| # No Timeout 0x00 |
| # 10 millisecond timeout 0x0A |
| NXP_SWP_SWITCH_TIMEOUT=0x0A |
| |
| ############################################################################### |
| # Enable or Disable RF_STATUS_UPDATE to EseHal module |
| # Disable 0x00 |
| # Enable 0x01 |
| RF_STATUS_UPDATE_ENABLE=0x00 |
| |
| ############################################################################### |
| # Configure the single default SE to use. The default is to use the first |
| # SE that is detected by the stack. This value might be used when the phone |
| # supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use |
| # one of them (e.g. 0xF4). |
| DEFAULT_OFFHOST_ROUTE=0x80 |
| |
| ############################################################################### |
| # Configure the single default SE to use. The default is to use the first |
| # SE that is detected by the stack. This value might be used when the phone |
| # supports multiple SE (e.g. 0xF3 and 0xF4) but you want to force it to use |
| # one of them (e.g. 0xF4). |
| DEFAULT_NFCF_ROUTE=0xC0 |
| |
| ############################################################################### |
| # Configure the default NfcA/IsoDep techology and protocol route. Can be |
| # either a secure element (e.g. 0xF4) or the host (0x00) |
| DEFAULT_ROUTE=0x00 |
| |
| ############################################################################### |
| # Vendor Specific Proprietary Protocol & Discovery Configuration |
| # Set to 0xFF if unsupported |
| # byte[0] NCI_PROTOCOL_18092_ACTIVE |
| # byte[1] NCI_PROTOCOL_B_PRIME |
| # byte[2] NCI_PROTOCOL_DUAL |
| # byte[3] NCI_PROTOCOL_15693 |
| # byte[4] NCI_PROTOCOL_KOVIO |
| # byte[5] NCI_PROTOCOL_MIFARE |
| # byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO |
| # byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME |
| # byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME |
| NFA_PROPRIETARY_CFG={05, FF, FF, 06, 81, 80, 70, FF, FF} |
| |
| ############################################################################### |
| # Bail out mode |
| # If set to 1, NFCC is using bail out mode for either Type A or Type B poll. |
| NFA_POLL_BAIL_OUT_MODE=0x01 |
| |
| ############################################################################### |
| # White list of Hosts |
| # This values will be the Hosts(NFCEEs) in the HCI Network. |
| DEVICE_HOST_WHITE_LIST={C0, 02} |
| |
| ############################################################################### |
| # Extended APDU length for ISO_DEP |
| ISO_DEP_MAX_TRANSCEIVE=0xFEFF |
| |
| ############################################################################### |
| # Choose the presence-check algorithm for type-4 tag. If not defined, the default value is 1. |
| # 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm |
| # 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block |
| # 2 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check |
| # command is sent waiting for rsp and ntf. |
| PRESENCE_CHECK_ALGORITHM=2 |
| ############################################################################### |
| # Configure the NFC Extras to open and use a static pipe. If the value is |
| # not set or set to 0, then the default is use a dynamic pipe based on a |
| # destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value |
| # for each UICC (where F3="UICC0" and F4="UICC1") |
| OFF_HOST_ESE_PIPE_ID=0x16 |
| OFF_HOST_SIM_PIPE_ID=0x0A |
| |
| ############################################################################### |
| #Set the Felica T3T System Code Power state : |
| #This settings will be used when application does not set this parameter |
| # bit pos 0 = Switch On |
| # bit pos 1 = Switch Off |
| # bit pos 2 = Battery Off |
| # bit pos 3 = Screen On lock |
| # bit pos 4 = Screen off unlock |
| # bit pos 5 = Screen Off lock |
| DEFAULT_SYS_CODE_PWR_STATE=0x3B |
| |
| ############################################################################### |
