mac80211/ti-utils/ini_files/127x/RFMD_S_3.5.ini - platform/hardware/ti/wlan - Git at Google

 # INI Generator version 1.4; Aligned to TS version 6.1.2.0.27
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 1:   Non FEM-dependant section
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 1.1: General parameters
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 TXBiPFEMAutoDetect  = 00 # Length: 1; Unit: Options (0: Manual Mode, 1: Automatic mode); Format: Unsigned; Source: Customer; Comment: This parameter is used by the FW to decide if the front-end is determined automatically or manually
 TXBiPFEMManufacturer  = 00 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit1,0: used to determine which FEM vendor type is used on the platform (0: RFMD, 1: TQS, 2:SKW, 3:HP), Bit3,2: unused, Bit7-4:External/internal load (4-SKW SB, 5-SKW HB, 6-HP SB, 7-HP HB)
 RefClk  = 02 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit 0,1,2-0:19.2MHz,1:26MHz,2:38.4MHz[Default],3:52MHz,4:38.4MHz XTAL,5:26MHz XTAL, Bit 3-CLK_REQ type, 0=wired-OR, 1=push-pull, Bit 4-CLK_REQ polarity
 SettlingTime  = 05 # Length: 1; Unit: ms (0-15); Format: Unsigned; Source: Customer; Comment: The time from asserting CLK_REQ (low to high) to valid FREF clock on the device inputs
 ClockValidOnWakeup  = 00 # Length: 1; Unit: Options (0: Reference clock not valid, 1: Reference clock is valid and stable); Format: Unsigned; Source: Customer; Comment: This parameter indicates whether the FREF clock is valid on wakeup
 DC2DCMode  = 00 # Length: 1; Unit: Bit_Options; Format: Unsigned, Source: Customer; Comment: Bit0 - DC2DC mode (0: btSPI is not used;1: btSPI used mux DC2DC to BT_FUNC2), Bit1- Level shifter support (0: No LS, 1: With LS)
 Single_Dual_Band_Solution  = 00 # Length: 1; Unit: Options (0: Single band, 1: Dual band); Format: Unsigned; Source: Customer; Comment: This parameter indicates if the solution is single band (2.4GHz only) or dual band (2.4GHz & 5GHz)
 Settings  = 01 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit0-NBI(0:Off,1:On),Bit1-Telec ch14(0:Off,1:On),Bit2-FEM0-LB,Bit3-FEM0-HB,Bit4-FEM1-LB,Bit5-FEM1-HB-TX BiP load(0:Int.,1:Ext.),Bit6-LPD LB,Bit7-LPD HB
 SRState = 00 # Length: 1; Unit: Options (0: Disabled, 1: Enabled); Format: Decimal; Source: TI; Comment: Smart Reflax (proprietary mechanism of TI that identify the silicon process specific params) state
 SRF1 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 0F 3F  # Length: 16; Unit: SRF1 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
 SRF2 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00  # Length: 16; Unit: SRF2 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
 SRF3 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00  # Length: 16; Unit: SRF3 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
 #SR_Debug_Table = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00  # Length: 16; Unit: SR_Debug_Table values; Format: Signed; Source: TI; Comment: SR Debug values  for TI internal use only
 #SR_SEN_N_P = 22 # Length: 1; Unit: SR_SEN_N_P values; Format: Unsigned; Source: TI; Comment: SR Debug values  for TI internal use only
 #SR_SEN_N_P_Gain = a9 # Length: 1; Unit: SR_SEN_N_P_GAIN values; Format: Unsigned; Source: TI; Comment: SR Debug values  for TI internal use only
 #SR_SEN_NRN = c1 # Length: 1; Unit: SR_SEN_NRN values; Format: Unsigned; Source: TI ; Comment: SR Debug values  for TI internal use only
 #SR_SEN_PRN = 8d # Length: 1; Unit: SR_SEN_PRN values; Format: Unsigned; Source: TI ; Comment: SR Debug values  for TI internal use only
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 1.2: Band-dependant parameters
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 1.2.1: 2.4G parameters
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 RxTraceInsertionLoss_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter indicates the printed circuit board (PCB) trace insertion loss
 TXTraceLoss_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter is used to align the output power to a different location on the board
 RxRssiAndProcessCompensation_2_4G  = EC F6 00 0C 18 F8 FC 00 08 10 F0 F8 00 0A 14 # Length: 15; Unit: 1/8dB; Format: Signed; Source: TI; Comment: The RSSI corner points are determined during RSSI temperature and process characterization
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 1.2.2: 5G parameters
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 2:     FEM-dependant section
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 2.1:   FEM parameters
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 #
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 2.1.1: 2.4G parameters
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 FEM0_TXBiPReferencePDvoltage_2_4G = 0136 # Length: 1; Unit: 1mV; Format: Unsigned; Source: TI; Comment: This parameter define the reference point of the FEM power detector
 FEM0_TxBiPReferencePower_2_4G  = 80 # Length: 1; Unit: 1/8dB; Format: Signed; Source: TI; Comment: Reference output power that produces given reference power detector output voltage .
 FEM0_TxBiPOffsetdB_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Signed; Source: Customer; Comment: This field is used to fine-tune the TX BiP by the customer
 FEM0_TxPerRatePowerLimits_2_4G_Normal = 1D 1F 22 26 27 29 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
 FEM0_TxPerRatePowerLimits_2_4G_Degraded = 19 1F 22 25 25 27 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
 FEM0_TxPerRatePowerLimits_2_4G_Extreme = 16 1D 1E 20 24 25 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
 FEM0_DegradedLowToNormalThr_2_4G = 1E # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
 FEM0_NormalToDegradedHighThr_2_4G = 2D # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
 FEM0_TxPerChannelPowerLimits_2_4G_11b = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
 FEM0_TxPerChannelPowerLimits_2_4G_OFDM = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
 FEM0_TxPDVsRateOffsets_2_4G = 01 02 02 02 02 00 # Length: 6; Unit: 1/8dB; Format: Signed; Source: TI; Comment: This parameter is a power detector offset value used to correct the power detector curve for each rate group
 FEM0_TxIbiasTable_2_4G  = 31 31 36 36 3b 3b # Length: 6; Unit: Codeword ; Format: Unsigned; Source: TI; Comment: This parameter sets the bias current provided by the SoC to the PA in the FEM. Options (MCS7, 54/48, 36/24, 18/12, 9/6, 11b)
 FEM0_RxFemInsertionLoss_2_4G  = 0E # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: TI; Comment: This parameter specifies the received insertion loss of the WL127x
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
 # SECTION 2.1.2: 5G parameters
 #------------------------------------------------------------------------------------------------------------------------------------------------------------
	# INI Generator version 1.4; Aligned to TS version 6.1.2.0.27
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 1: Non FEM-dependant section
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 1.1: General parameters
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	TXBiPFEMAutoDetect = 00 # Length: 1; Unit: Options (0: Manual Mode, 1: Automatic mode); Format: Unsigned; Source: Customer; Comment: This parameter is used by the FW to decide if the front-end is determined automatically or manually
	TXBiPFEMManufacturer = 00 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit1,0: used to determine which FEM vendor type is used on the platform (0: RFMD, 1: TQS, 2:SKW, 3:HP), Bit3,2: unused, Bit7-4:External/internal load (4-SKW SB, 5-SKW HB, 6-HP SB, 7-HP HB)
	RefClk = 02 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit 0,1,2-0:19.2MHz,1:26MHz,2:38.4MHz[Default],3:52MHz,4:38.4MHz XTAL,5:26MHz XTAL, Bit 3-CLK_REQ type, 0=wired-OR, 1=push-pull, Bit 4-CLK_REQ polarity
	SettlingTime = 05 # Length: 1; Unit: ms (0-15); Format: Unsigned; Source: Customer; Comment: The time from asserting CLK_REQ (low to high) to valid FREF clock on the device inputs
	ClockValidOnWakeup = 00 # Length: 1; Unit: Options (0: Reference clock not valid, 1: Reference clock is valid and stable); Format: Unsigned; Source: Customer; Comment: This parameter indicates whether the FREF clock is valid on wakeup
	DC2DCMode = 00 # Length: 1; Unit: Bit_Options; Format: Unsigned, Source: Customer; Comment: Bit0 - DC2DC mode (0: btSPI is not used;1: btSPI used mux DC2DC to BT_FUNC2), Bit1- Level shifter support (0: No LS, 1: With LS)
	Single_Dual_Band_Solution = 00 # Length: 1; Unit: Options (0: Single band, 1: Dual band); Format: Unsigned; Source: Customer; Comment: This parameter indicates if the solution is single band (2.4GHz only) or dual band (2.4GHz & 5GHz)
	Settings = 01 # Length: 1; Unit: Bit_Options; Format: Unsigned; Source: Customer; Comment: Bit0-NBI(0:Off,1:On),Bit1-Telec ch14(0:Off,1:On),Bit2-FEM0-LB,Bit3-FEM0-HB,Bit4-FEM1-LB,Bit5-FEM1-HB-TX BiP load(0:Int.,1:Ext.),Bit6-LPD LB,Bit7-LPD HB
	SRState = 00 # Length: 1; Unit: Options (0: Disabled, 1: Enabled); Format: Decimal; Source: TI; Comment: Smart Reflax (proprietary mechanism of TI that identify the silicon process specific params) state
	SRF1 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 0F 3F # Length: 16; Unit: SRF1 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
	SRF2 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00 # Length: 16; Unit: SRF2 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
	SRF3 = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00 # Length: 16; Unit: SRF3 values; Format: Signed; Source: TI; Comment: The table holds the specific parameters for using the SmartReflex mechanism
	#SR_Debug_Table = 09 04 18 10 08 00 F7 EF E7 DF 00 00 00 00 00 00 # Length: 16; Unit: SR_Debug_Table values; Format: Signed; Source: TI; Comment: SR Debug values for TI internal use only
	#SR_SEN_N_P = 22 # Length: 1; Unit: SR_SEN_N_P values; Format: Unsigned; Source: TI; Comment: SR Debug values for TI internal use only
	#SR_SEN_N_P_Gain = a9 # Length: 1; Unit: SR_SEN_N_P_GAIN values; Format: Unsigned; Source: TI; Comment: SR Debug values for TI internal use only
	#SR_SEN_NRN = c1 # Length: 1; Unit: SR_SEN_NRN values; Format: Unsigned; Source: TI ; Comment: SR Debug values for TI internal use only
	#SR_SEN_PRN = 8d # Length: 1; Unit: SR_SEN_PRN values; Format: Unsigned; Source: TI ; Comment: SR Debug values for TI internal use only
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 1.2: Band-dependant parameters
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 1.2.1: 2.4G parameters
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	RxTraceInsertionLoss_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter indicates the printed circuit board (PCB) trace insertion loss
	TXTraceLoss_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: Customer; Comment: This parameter is used to align the output power to a different location on the board
	RxRssiAndProcessCompensation_2_4G = EC F6 00 0C 18 F8 FC 00 08 10 F0 F8 00 0A 14 # Length: 15; Unit: 1/8dB; Format: Signed; Source: TI; Comment: The RSSI corner points are determined during RSSI temperature and process characterization
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 1.2.2: 5G parameters
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 2: FEM-dependant section
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 2.1: FEM parameters
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	#
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 2.1.1: 2.4G parameters
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	FEM0_TXBiPReferencePDvoltage_2_4G = 0136 # Length: 1; Unit: 1mV; Format: Unsigned; Source: TI; Comment: This parameter define the reference point of the FEM power detector
	FEM0_TxBiPReferencePower_2_4G = 80 # Length: 1; Unit: 1/8dB; Format: Signed; Source: TI; Comment: Reference output power that produces given reference power detector output voltage .
	FEM0_TxBiPOffsetdB_2_4G = 00 # Length: 1; Unit: 1/8dB; Format: Signed; Source: Customer; Comment: This field is used to fine-tune the TX BiP by the customer
	FEM0_TxPerRatePowerLimits_2_4G_Normal = 1D 1F 22 26 27 29 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
	FEM0_TxPerRatePowerLimits_2_4G_Degraded = 19 1F 22 25 25 27 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
	FEM0_TxPerRatePowerLimits_2_4G_Extreme = 16 1D 1E 20 24 25 # Length: 6; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
	FEM0_DegradedLowToNormalThr_2_4G = 1E # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
	FEM0_NormalToDegradedHighThr_2_4G = 2D # Length: 1; Unit: 1/10 volts; Format: Unsigned; Source: TI; Comment: The limits are applied to the power control process according to the VBAT and temp range in which the FEM is operating
	FEM0_TxPerChannelPowerLimits_2_4G_11b = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
	FEM0_TxPerChannelPowerLimits_2_4G_OFDM = 50 50 50 50 50 50 50 50 50 50 50 50 50 50 # Length: 14; Unit: 1/2dB; Format: Signed; Source: Customer; Comment: The purpose of this table is to allow clipping of the maximum output power on certain channels
	FEM0_TxPDVsRateOffsets_2_4G = 01 02 02 02 02 00 # Length: 6; Unit: 1/8dB; Format: Signed; Source: TI; Comment: This parameter is a power detector offset value used to correct the power detector curve for each rate group
	FEM0_TxIbiasTable_2_4G = 31 31 36 36 3b 3b # Length: 6; Unit: Codeword ; Format: Unsigned; Source: TI; Comment: This parameter sets the bias current provided by the SoC to the PA in the FEM. Options (MCS7, 54/48, 36/24, 18/12, 9/6, 11b)
	FEM0_RxFemInsertionLoss_2_4G = 0E # Length: 1; Unit: 1/8dB; Format: Unsigned; Source: TI; Comment: This parameter specifies the received insertion loss of the WL127x
	#------------------------------------------------------------------------------------------------------------------------------------------------------------
	# SECTION 2.1.2: 5G parameters
	#------------------------------------------------------------------------------------------------------------------------------------------------------------