blob: 0b4455ae42c769b4e439c3b4a9e2b68f39ad17dd [file] [log] [blame]
/*
* Copyright (C) 2010 NXP Semiconductors
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
/**
* \file nfc_custom_config.h
* \brief HAL Custom Configurations
*
*
* \note This is the configuration header file of the HAL 4.0. custom configurable
* parameters of the HAL 4.0 are provided in this file
*
* Project: NFC-FRI-1.1 / HAL4.0
*
* $Date: Fri Jun 11 16:44:31 2010 $
* $Author: ing04880 $
* $Revision: 1.11 $
* $Aliases: NFC_FRI1.1_WK1023_R35_1 $
*
*/
/*@{*/
#ifndef NFC_CUSTOM_CONFIG_H
#define NFC_CUSTOM_CONFIG_H
/*@}*/
/**
* \name Hal
*
* File: \ref nfc_custom_config.h
*
*/
/*
*****************************************************************
********************** CUSTOM MACROS **************************
*****************************************************************
*/
/**< Max number of remote devices supported*/
#define MAX_REMOTE_DEVICES 0x10
/**< Default Session ID for Initialisation */
#define DEFAULT_SESSION "NXP-NFC2"
/** Resolution value for the timer, here the
timer resolution is 100 milliseconds */
#define TIMER_RESOLUTION 100U
/**< Defines connection time out value for LLC timer,
500 is in milliseconds */
#define LINK_CONNECTION_TIMEOUT 500U
/**< Defines guard time out value for LLC timer,
250 is in milliseconds */
#define LINK_GUARD_TIMEOUT 250U
/**< Macro to Enable SMX Feature During
* Initialisation */
/* PLEASE NOTE: This Macro should be only enabled if there is a SMART_MX
* Chip attached to the PN544.
*/
/* #define NXP_HAL_ENABLE_SMX */
/* PLEASE NOTE: Kindly change the DEFAULT_SESSION Macro for each of the
* configuration change done for the below Macros
*/
/**< External Clock Request Configuration for the NFC Device,
0x00U -> No Clock Request,
0x01U -> Clock Request through CLKREQ pin (GPIO pin 2),
0x02U -> Clock Request through NXP_EVT_CLK_REQUEST Event,
*/
#define NXP_DEFAULT_CLK_REQUEST 0x00U
/**< External Input Clock Setting for the NFC Device,
0x00U -> No Input Clock Required (Use the Xtal),
0x01U -> 13 MHZ,
0x02U -> 19.2 MHZ,
0x03U -> 26 MHZ,
0x04U -> 38.4 MHZ,
0x05U -> Custom (Set the Custome Clock Registry),
*/
#define NXP_DEFAULT_INPUT_CLK 0x00U
#define NFC_DEV_HWCONF_DEFAULT 0xBCU
/**< TX LDO Configuration
0x00 -> 00b 3.0 V,
0x01 -> 01b 3.0 V,
0x02 -> 10b 2.7 V,
0x03 -> 11b 3.3 V,
*/
#define NXP_DEFAULT_TX_LDO 0x00U
/**< External Clock Request Configuration for the NFC Device,
0x00U -> No Power Request,
0x01U -> Power Request through CLKREQ pin (GPIO pin 2),
0x02U -> Power Request through PWR_REQUEST (GPIO Pin 3),
*/
#define NXP_UICC_PWR_REQUEST 0x00U
/**< UICC Bit Rate Configuration
0x02U -> 212Kbits/Sec
0x04U -> 424Kbits/Sec
0x08U -> 828Kbits/Sec
*/
#define NXP_UICC_BIT_RATE 0x08U
/**< Indicates PN544 Power Modes Configuration for the NFC Device,
0x00U -> PN544 stays in active bat mode
(except when generating RF field)
0x01U -> PN544 goes in standby when possible otherwise
stays in active bat mode
0x02U -> PN544 goes in idle mode as soon as it can
(otherwise it is in active bat except when generating RF field)
0x03U -> PN544 goes in standby when possible otherwise goes in idle mode
as soon as it can (otherwise it is in active bat except when
generating RF field)
*/
#define NXP_SYSTEM_PWR_STATUS 0x01U
/**< System Event Notification
0x01 Overcurrent
0x02 PMUVCC Switch
0x04 External RF Field
0x08 Memory Violation
0x10 Temperature Overheat
*/
#define NXP_SYSTEM_EVT_INFO 0x10U
/**< NFCIP Active Mode Configuration
0x01 106 kbps
0x02 212 kbps
0x04 424 kbps
*/
#define NXP_NFCIP_ACTIVE_DEFAULT 0x01U
/* Reset the Default values of Host Link Timers */
/* Macro to Enable the Host Side Link Timeout Configuration
* 0x00 ----> Default Pre-defined Configuration;
* 0x01 ----> Update only the Host Link Guard Timeout Configuration;
* 0x03 ----> Update Both the Host Link Guard Timeout
and ACK Timeout Configuration;
*/
#define HOST_LINK_TIMEOUT 0x00U
#define NXP_NFC_LINK_GRD_CFG_DEFAULT 0x0032U
#define NXP_NFC_LINK_ACK_CFG_DEFAULT 0x0005U
/* Macro to Enable the Interface Character Timeout Configuration
* 0x00 ----> Default Pre-defined Configuration;
* 0x01 ----> Update the IFC Timeout Default Configuration;
*/
#define NXP_NFC_IFC_TIMEOUT 0x00
#define NXP_NFC_IFC_CONFIG_DEFAULT 0x203AU
#define NXP_NFCIP_PSL_BRS_DEFAULT 0x00U
#endif /* NFC_CUSTOM_CONFIG_H */