| /* |
| * Copyright (C) 2012 The Android Open Source Project |
| * |
| * Licensed under the Apache License, Version 2.0 (the "License"); |
| * you may not use this file except in compliance with the License. |
| * You may obtain a copy of the License at |
| * |
| * http://www.apache.org/licenses/LICENSE-2.0 |
| * |
| * Unless required by applicable law or agreed to in writing, software |
| * distributed under the License is distributed on an "AS IS" BASIS, |
| * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. |
| * See the License for the specific language governing permissions and |
| * limitations under the License. |
| */ |
| #ifndef _HCI_H_ |
| #define _HCI_H_ |
| |
| |
| //http://webee.technion.ac.il/labs/comnet/projects/winter02/cn08w02/HCI_spec.pdf |
| |
| |
| #define HCI_OPCODE(ogf, ocf) ((((unsigned short)(ogf)) << 10) | (ocf)) |
| |
| typedef struct{ |
| |
| unsigned short opcode; |
| unsigned char totalParamLen; |
| unsigned char params[]; |
| |
| }HCI_Cmd; |
| |
| typedef struct{ |
| |
| unsigned char eventCode; |
| unsigned char totalParamLen; |
| unsigned char params[]; |
| |
| }HCI_Event; |
| |
| #define HCI_DATA_INFO(conn, pbf, bcf) (((conn & 0xEFF) | (((unsigned short)(pbf)) << 12) | (((unsigned short)(bcf)) << 14)) |
| #define HCI_CONN(info) ((info) & 0xEFF) |
| #define HCI_PBF(info) (((info) >> 12) & 3) |
| #define HCI_BCF(info) (((info) >> 14) & 3) |
| |
| #define HCI_PBF_First_Message 2 |
| #define HCI_PBF_Continuing_Message 1 |
| |
| //BCF Common |
| #define HCI_BCF_Point_To_Point 0 |
| |
| //BCF from host to controller |
| #define HCI_BCF_Active_Broadcast 1 |
| #define HCI_BCF_Piconet_Broadcast 2 |
| |
| //BCF from controller |
| #define HCI_BCF_RXed_In_Active_State 1 |
| #define HCI_BCF_RXed_In_Parked_State 2 |
| |
| typedef struct{ |
| |
| unsigned short info; //connection handle & flags |
| unsigned short totalDataLen; |
| unsigned char data[]; |
| |
| }HCI_ACL_Data; |
| |
| |
| typedef struct{ |
| |
| unsigned short info; //connection handle & flags [reserved] |
| unsigned char totalDataLen; |
| unsigned char data[]; |
| |
| }HCI_SCO_Data; |
| |
| |
| #define HCI_LAP_Unlimited_Inquiry 0x9E8B33 |
| #define HCI_LAP_Limited_Inquiry 0x9E8B00 |
| |
| #define UART_PKT_TYP_CMD 1 |
| #define UART_PKT_TYP_ACL 2 |
| #define UART_PKT_TYP_SCO 3 |
| #define UART_PKT_TYP_EVT 4 |
| |
| #define PAGE_STATE_INQUIRY 1 |
| #define PAGE_STATE_PAGE 2 |
| |
| #define DEVICE_CLASS_SERVICE_POSITIONING 0x010000 //GPS |
| #define DEVICE_CLASS_SERVICE_NETWORKING 0x020000 //LAN |
| #define DEVICE_CLASS_SERVICE_RENDERING 0x040000 //PRINTER, SPEAKER |
| #define DEVICE_CLASS_SERVICE_CAPTURING 0x080000 //SCANNER, MICROPHONE |
| #define DEVICE_CLASS_SERVICE_OBEX 0x100000 //v-Inbox, v-Folder, v-$WORD |
| #define DEVICE_CLASS_SERVICE_AUDIO 0x200000 //SPEAKER, MIC, HEADSET |
| #define DEVICE_CLASS_SERVICE_TELEPHONY 0x400000 //MODEM, HEADSET |
| #define DEVICE_CLASS_SERVICE_INFORMATION 0x800000 //WEB-server, WAP-server |
| |
| #define DEVICE_CLASS_MAJOR_SHIFT 8 |
| #define DEVICE_CLASS_MAJOR_MASK 0x001F00 |
| |
| #define DEVICE_CLASS_MAJOR_MISC 0 |
| #define DEVICE_CLASS_MAJOR_COMPUTER 1 |
| #define DEVICE_CLASS_MAJOR_PHONE 2 |
| #define DEVICE_CLASS_MAJOR_LAN 3 |
| #define DEVICE_CLASS_MAJOR_AV 4 |
| #define DEVICE_CLASS_MAJOR_PERIPH 5 |
| #define DEVICE_CLASS_MAJOR_IMAGING 6 |
| #define DEVICE_CLASS_MAJOR_WEARABLE 7 |
| #define DEVICE_CLASS_MAJOR_TOY 8 |
| #define DEVICE_CLASS_MAJOR_HEALTH 9 |
| #define DEVICE_CLASS_MAJOR_UNCATEGORIZED 31 |
| |
| #define DEVICE_CLASS_MINOR_COMPUTER_SHIFT 2 |
| #define DEVICE_CLASS_MINOR_COMPUTER_MASK 0xFC |
| #define DEVICE_CLASS_MINOR_COMPUTER_UNCATEG 0 |
| #define DEVICE_CLASS_MINOR_COMPUTER_DESKTOP 1 |
| #define DEVICE_CLASS_MINOR_COMPUTER_SERVER 2 |
| #define DEVICE_CLASS_MINOR_COMPUTER_LAPTOP 3 |
| #define DEVICE_CLASS_MINOR_COMPUTER_CLAM_PDA 4 |
| #define DEVICE_CLASS_MINOR_COMPUTER_PALM_PDA 5 |
| #define DEVICE_CLASS_MINOR_COMPUTER_WEARABLE 6 |
| |
| #define DEVICE_CLASS_MINOR_PHONE_SHIFT 2 |
| #define DEVICE_CLASS_MINOR_PHONE_MASK 0xFC |
| #define DEVICE_CLASS_MINOR_PHONE_UNCATEG 0 |
| #define DEVICE_CLASS_MINOR_PHONE_CELL 1 |
| #define DEVICE_CLASS_MINOR_PHONE_CORDLESS 2 |
| #define DEVICE_CLASS_MINOR_PHONE_SMART 3 |
| #define DEVICE_CLASS_MINOR_PHONE_MODEM 4 |
| #define DEVICE_CLASS_MINOR_PHONE_ISDN 5 |
| |
| #define DEVICE_CLASS_MINOR_AV_SHIFT 2 |
| #define DEVICE_CLASS_MINOR_AV_MASK 0xFC |
| #define DEVICE_CLASS_MINOR_AV_UNCATEG 0 |
| #define DEVICE_CLASS_MINOR_AV_HEADSET 1 |
| #define DEVICE_CLASS_MINOR_AV_HANDSFREE 2 |
| #define DEVICE_CLASS_MINOR_AV_MIC 4 |
| #define DEVICE_CLASS_MINOR_AV_LOUDSPEAKER 5 |
| #define DEVICE_CLASS_MINOR_AV_HEADPHONES 6 |
| #define DEVICE_CLASS_MINOR_AV_PORTBL_AUDIO 7 |
| #define DEVICE_CLASS_MINOR_AV_CAR_AUDIO 8 |
| #define DEVICE_CLASS_MINOR_AV_SET_TOP_BOX 9 |
| #define DEVICE_CLASS_MINOR_AV_HIFI 10 |
| #define DEVICE_CLASS_MINOR_AV_VCR 11 |
| #define DEVICE_CLASS_MINOR_AV_VID_CAM 12 |
| #define DEVICE_CLASS_MINOR_AV_CAMCORDER 13 |
| #define DEVICE_CLASS_MINOR_AV_VID_MONITOR 14 |
| #define DEVICE_CLASS_MINOR_AV_DISPLAY_AND_SPKR 15 |
| #define DEVICE_CLASS_MINOR_AV_VC 16 |
| #define DEVICE_CLASS_MINOR_AV_TOY 18 |
| |
| |
| //COMMANDS |
| |
| #define HCI_OGF_Link_Control 1 |
| |
| #define HCI_CMD_Inquiry 0x0001 //enter Inquiry mode where it discovers other Bluetooth devices. |
| #define HCI_CMD_Inquiry_Cancel 0x0002 //cancel the Inquiry mode in which the Bluetooth device is in. |
| #define HCI_CMD_Periodic_Inquiry_Mode 0x0003 //set the device to enter Inquiry modes periodically according to the time interval set. |
| #define HCI_CMD_Exit_Periodic_Inquiry_Mode 0x0004 //exit the periodic Inquiry mode |
| #define HCI_CMD_Create_Connection 0x0005 //create an ACL connection to the device specified by the BD_ADDR in the parameters. |
| #define HCI_CMD_Disconnect 0x0006 //terminate the existing connection to a device |
| #define HCI_CMD_Add_SCO_Connection 0x0007 //Create an SCO connection defined by the connection handle parameters. |
| #define HCI_CMD_Accept_Connection_Request 0x0009 //accept a new connection request |
| #define HCI_CMD_Reject_Connection_Request 0x000A //reject a new connection request |
| #define HCI_CMD_Link_Key_Request_Reply 0x000B //Reply to a link key request event sent from controller to the host |
| #define HCI_CMD_Link_Key_Request_Negative_Reply 0x000C //Reply to a link key request event from the controller to the host if there is no link key associated with the connection. |
| #define HCI_CMD_PIN_Code_Request_Reply 0x000D //Reply to a PIN code request event sent from a controller to the host. |
| #define HCI_CMD_PIN_Code_Request_Negative_Reply 0x000E //Reply to a PIN code request event sent from the controller to the host if there is no PIN associated with the connection. |
| #define HCI_CMD_Change_Connection_Packet_Type 0x000F //change the type of packets to be sent for an existing connection. |
| #define HCI_CMD_Authentication_Requested 0x0011 //establish authentication between two devices specified by the connection handle. |
| #define HCI_CMD_Set_Connection_Encryption 0x0013 //enable or disable the link level encryption. |
| #define HCI_CMD_Change_Connection_Link_Key 0x0015 //force the change of a link key to a new one between two connected devices. |
| #define HCI_CMD_Master_Link_Key 0x0017 //force two devices to use the master's link key temporarily. |
| #define HCI_CMD_Remote_Name_Request 0x0019 //determine the user friendly name of the connected device. |
| #define HCI_CMD_Read_Remote_Supported_Features 0x001B //determine the features supported by the connected device. |
| #define HCI_CMD_Read_Remote_Version_Information 0x001D //determine the version information of the connected device. |
| #define HCI_CMD_Read_Clock_Offset 0x001F //read the clock offset of the remote device. |
| //BT2.1 SSP |
| #define HCI_CMD_IO_Capability_Request_Reply 0x002B |
| #define HCI_CMD_User_Confirmation_Request_Reply 0x002C |
| #define HCI_CMD_User_Confirmation_Request_Negative_Reply 0x002D |
| #define HCI_CMD_User_Passkey_Request_Reply 0x002E |
| #define HCI_CMD_User_Passkey_Request_Negative_Reply 0x002F |
| #define HCI_CMD_Remote_OOB_Data_Request_Reply 0x0030 |
| #define HCI_CMD_Remote_OOB_Data_Request_Negative_Reply 0x0033 |
| #define HCI_CMD_IO_Capability_Request_Negative_Reply 0x0034 |
| |
| #define HCI_OGF_Policy 2 |
| |
| #define HCI_CMD_Hold_Mode 0x0001 //place the current or remote device into the Hold mode state. |
| #define HCI_CMD_Sniff_Mode 0x0003 //place the current or remote device into the Sniff mode state. |
| #define HCI_CMD_Exit_Sniff_Mode 0x0004 //exit the current or remote device from the Sniff mode state. |
| #define HCI_CMD_Park_Mode 0x0005 //place the current or remote device into the Park mode state. |
| #define HCI_CMD_Exit_Park_Mode 0x0006 //exit the current or remote device from the Park mode state. |
| #define HCI_CMD_QoS_Setup 0x0007 //setup the Quality of Service parameters of the device. |
| #define HCI_CMD_Role_Discovery 0x0009 //determine the role of the device for a particular connection. |
| #define HCI_CMD_Switch_Role 0x000B //allow the device to switch roles for a particular connection. |
| #define HCI_CMD_Read_Link_Policy_Settings 0x000C //determine the link policy that the LM can use to establish connections. |
| #define HCI_CMD_Write_Link_Policy_Settings 0x000D //set the link policy that the LM can use for a particular connection. |
| |
| |
| #define HCI_OGF_Controller_and_Baseband 3 |
| |
| #define HCI_CMD_Set_Event_Mask 0x0001 //set which events are generated by the HCI for the host. |
| #define HCI_CMD_Reset 0x0003 //reset the host controller, link manager and the radio module. |
| #define HCI_CMD_Set_Event_Filter 0x0005 //used by host to set the different types of event filters that the host needs to receive. |
| #define HCI_CMD_Flush 0x0008 //flush all pending data packets for transmission for a particular connection handle. |
| #define HCI_CMD_Read_PIN_Type 0x0009 //used by host to determine if the link manager assumes that the host requires a variable PIN type or fixed PIN code. PIN is used during pairing. |
| #define HCI_CMD_Write_PIN_Type 0x000A //used by host to write to the host controller on the PIN type supported by the host. |
| #define HCI_CMD_Create_New_Unit_Key 0x000B //create a new unit key. |
| #define HCI_CMD_Read_Stored_Link_Key 0x000D //read the link key stored in the host controller. |
| #define HCI_CMD_Write_Stored_Link_Key 0x0011 //write the link key to the host controller. |
| #define HCI_CMD_Delete_Stored_Link_Key 0x0012 //delete a stored link key in the host controller. |
| #define HCI_CMD_Change_Local_Name 0x0013 //modify the user friendly name of the device. |
| #define HCI_CMD_Read_Local_Name 0x0014 //read the user friendly name of the device. |
| #define HCI_CMD_Read_Connection_Accept_Timeout 0x0015 //determine the timeout session before the host denies and rejects a new connection request. |
| #define HCI_CMD_Write_Connection_Accept_Timeout 0x0016 //set the timeout session before a device can deny or reject a connection request. |
| #define HCI_CMD_Read_Page_Timeout 0x0017 //read the timeout value where a device will wait for a connection acceptance before sending a connection failure is returned. |
| #define HCI_CMD_Write_Page_Timeout 0x0018 //write the timeout value where a device will wait for a connection acceptance before sending a connection failure is returned. |
| #define HCI_CMD_Read_Scan_Enable 0x0019 //read the status of the Scan_Enable configuration. |
| #define HCI_CMD_Write_Scan_Enable 0x001A //set the status of the Scan_Enable configuration. |
| #define HCI_CMD_Read_Page_Scan_Activity 0x001B //read the value of the Page_Scan_Interval and Page_Scan_Window configurations. |
| #define HCI_CMD_Write_Page_Scan_Activity 0x001C //write the value of the Page_Scan_Interval and Page_Scan_Window configurations. |
| #define HCI_CMD_Read_Inquiry_Scan_Activity 0x001D //read the value of the Inquiry_Scan_Interval and Inquiry_Scan_Window configurations. |
| #define HCI_CMD_Write_Inquiry_Scan_Activity 0x001E //set the value of the Inquiry_Scan_Interval and Inquiry_Scan_Window configurations. |
| #define HCI_CMD_Authentication_Enable 0x001F //read the Authentication_Enable parameter. |
| #define HCI_CMD_Write_Authentication_Enable 0x0020 //set the Authentication_Enable parameter. |
| #define HCI_CMD_Read_Encryption_Mode 0x0021 //read the Encryption_Mode parameter. |
| #define HCI_CMD_Write_Encryption_Mode 0x0022 //write the Encryption_Mode parameter. |
| #define HCI_CMD_Read_Class_Of_Device 0x0023 //read the Class_Of_Device parameter. |
| #define HCI_CMD_Write_Class_Of_Device 0x0024 //set the Class_Of_Device parameter. |
| #define HCI_CMD_Read_Voice_Setting 0x0025 //read the Voice_Setting parameter. Used for voice connections. |
| #define HCI_CMD_Voice_Setting 0x0026 //set the Voice_Setting parameter. Used for voice connections. |
| #define HCI_CMD_Read_Automatic_Flush_Timeout 0x0027 //read the Flush_Timeout parameter. Used for ACL connections only. |
| #define HCI_CMD_Write_Automatic_Flush_Timeout 0x0028 //set the Flush_Timeout parameter. Used for ACL connections only. |
| #define HCI_CMD_Read_Num_Broadcast_Retransmissions 0x0029 //read the number of time a broadcast message is retransmitted. |
| #define HCI_CMD_Write_Num_Broadcast_Retransmissions 0x002A //set the number of time a broadcast message is retransmitted. |
| #define HCI_CMD_Read_Hold_Mode_Activity 0x002B //set the Hold_Mode activity to instruct the device to perform an activity during hold mode. |
| #define HCI_CMD_Write_Hold_Mode_Activity 0x002C //set the Hold_Mode_Activity parameter. |
| #define HCI_CMD_Transmit_Power_Level 0x002D //read the power level required for transmission for a connection handle. |
| #define HCI_CMD_Read_SCO_Flow_Control_Enable 0x002E //check the current status of the flow control for the SCO connection. |
| #define HCI_CMD_SCO_Flow_Control_Enable 0x002F //set the status of the flow control for a connection handle. |
| #define HCI_CMD_Set_Host_Controller_To_Host_Flow_Control 0x0031 //set the flow control from the host controller to host in on or off state. |
| #define HCI_CMD_Host_Buffer_Size 0x0033 //set by host to inform the host controller of the buffer size of the host for ACL and SCO connections. |
| #define HCI_CMD_Host_Number_Of_Completed_Packets 0x0035 //set from host to host controller when it is ready to receive more data packets. |
| #define HCI_CMD_Read_Link_Supervision_Timeout 0x0036 //read the timeout for monitoring link losses. |
| #define HCI_CMD_Write_Link_Supervision_Timeout 0x0037 //set the timeout for monitoring link losses. |
| #define HCI_CMD_Read_Number_Of_Supported_IAC 0x0038 //read the number of IACs that the device can listen on during Inquiry access. |
| #define HCI_CMD_Read_Current_IAC_LAP 0x0039 //read the LAP for the current IAC. |
| #define HCI_CMD_Write_Current_IAC_LAP 0x003A //set the LAP for the current IAC. |
| #define HCI_CMD_Read_Page_Scan_Period_Mode 0x003B //read the timeout session of a page scan. |
| #define HCI_CMD_Write_Page_Scan_Period_Mode 0x003C //set the timeout session of a page scan. |
| #define HCI_CMD_Read_Page_Scan_Mode 0x003D //read the default Page scan mode. |
| #define HCI_CMD_Write_Page_Scan_Mode 0x003E //set the default page scan mode. |
| //BT2.1 SSP |
| #define HCI_CMD_Write_Simple_Pairing_Mode 0x0056 |
| |
| |
| #define HCI_OGF_Informational 4 |
| |
| #define HCI_CMD_Read_Local_Version_Information 0x0001 |
| #define HCI_CMD_Read_Local_Supported_Features 0x0003 |
| #define HCI_CMD_Read_Buffer_Size 0x0005 |
| #define HCI_CMD_Read_Country_Code 0x0007 |
| #define HCI_CMD_Read_BD_ADDR 0x0009 |
| |
| |
| //EVENTS |
| |
| #define HCI_EVT_Inquiry_Complete_Event 0x01 //Indicates the Inquiry has finished. |
| #define HCI_EVT_Inquiry_Result_Event 0x02 //Indicates that Bluetooth device(s) have responded for the inquiry. |
| #define HCI_EVT_Connection_Complete_Event 0x03 //Indicates to both hosts that the new connection has been formed. |
| #define HCI_EVT_Connection_Request_Event 0x04 //Indicates that a new connection is trying to be established. |
| #define HCI_EVT_Disconnection_Complete_Event 0x05 //Occurs when a connection has been disconnected. |
| #define HCI_EVT_Authentication_Complete_Event 0x06 //Occurs when an authentication has been completed. |
| #define HCI_EVT_Remote_Name_Request_Complete_Event 0x07 //Indicates that the request for the remote name has been completed. |
| #define HCI_EVT_Encryption_Change_Event 0x08 //Indicates that a change in the encryption has been completed. |
| #define HCI_EVT_Change_Connection_Link_Key_Complete_Event 0x09 //Indicates that the change in the link key has been completed. |
| #define HCI_EVT_Master_Link_Key_Complete_Event 0x0A //Indicates that the change in the temporary link key or semi permanent link key on the master device is complete. |
| #define HCI_EVT_Read_Remote_Supported_Features_Complete_Event 0x0B //Indicates that the reading of the supported features on the remote device is complete. |
| #define HCI_EVT_Read_Remote_Version_Complete_Event 0x0C //Indicates that the version number on the remote device has been read and completed. |
| #define HCI_EVT_QOS_Setup_Complete_Event 0x0D //Indicates that the Quality of Service setup has been complete. |
| #define HCI_EVT_Command_Complete_Event 0x0E //Used by controller to send status and event parameters to the host for the particular command. |
| #define HCI_EVT_Command_Status_Event 0x0F //Indicates that the command has been received and is being processed in the host controller. |
| #define HCI_EVT_Hardware_Error_Event 0x10 //Indicates a hardware failure of the Bluetooth device. |
| #define HCI_EVT_Flush_Occured_event 0x11 //Indicates that the data has been flushed for a particular connection. |
| #define HCI_EVT_Role_Change_Event 0x12 //Indicates that the current bluetooth role for a connection has been changed. |
| #define HCI_EVT_Number_Of_Completed_Packets_Event 0x13 //Indicates to the host the number of data packets sent compared to the last time the same event was sent. |
| #define HCI_EVT_Mode_Change_Event 0x14 //Indicates the change in mode from hold, sniff, park or active to another mode. |
| #define HCI_EVT_Return_Link_Keys_Event 0x15 //Used to return stored link keys after a Read_Stored_Link_Key command was issued. |
| #define HCI_EVT_PIN_Code_Request_Event 0x16 //Indicates the a PIN code is required for a new connection. |
| #define HCI_EVT_Link_Key_Request_Event 0x17 //Indicates that a link key is required for the connection. |
| #define HCI_EVT_Link_Key_Notification_Event 0x18 //Indicates to the host that a new link key has been created. |
| #define HCI_EVT_Loopback_Command_Event 0x19 //Indicates that command sent from the host will be looped back. |
| #define HCI_EVT_Data_Buffer_Overflow_Event 0x1A //Indicates that the data buffers on the host has overflowed. |
| #define HCI_EVT_Max_Slots_Change_Event 0x1B //Informs the host when the LMP_Max_Slots parameter changes. |
| #define HCI_EVT_Read_Clock_Offset_Complete_Event 0x1C //Indicates the completion of reading the clock offset information. |
| #define HCI_EVT_Connection_Packet_Type_Changed_Event 0x1D //Indicate the completion of the packet type change for a connection. |
| #define HCI_EVT_QoS_Violation_Event 0x1E //Indicates that the link manager is unable to provide the required Quality of Service. |
| #define HCI_EVT_Page_Scan_Mode_Change_Event 0x1F //Indicates that the remote device has successfully changed the Page Scan mode. |
| #define HCI_EVT_Page_Scan_Repetition_Mode_Change_Event 0x20 //Indicates that the remote device has successfully changed the Page Scan Repetition mode. |
| //BT2.1 SSP |
| #define HCI_EVT_IO_Capability_Request_Event 0x31 |
| #define HCI_EVT_IO_Capability_Response_Event 0x32 |
| #define HCI_EVT_User_Confirmation_Request_Event 0x33 |
| #define HCI_EVT_User_Passkey_Request_Event 0x34 |
| #define HCI_EVT_Remote_OOB Data_Request_Event 0x35 |
| #define HCI_EVT_Simple_Pairing_Complete_Event 0x36 |
| #define HCI_EVT_User_Passkey_Notification_Event 0x3B |
| |
| |
| |
| |
| //ERRORS |
| |
| #define HCI_ERR_Unknown_HCI_Command 0x01 |
| #define HCI_ERR_No_Connection 0x02 |
| #define HCI_ERR_Hardware_Failure 0x03 |
| #define HCI_ERR_Page_Timeout 0x04 |
| #define HCI_ERR_Authentication_Failure 0x05 |
| #define HCI_ERR_Key_Missing 0x06 |
| #define HCI_ERR_Memory_Full 0x07 |
| #define HCI_ERR_Connection_Timeout 0x08 |
| #define HCI_ERR_Max_Number_Of_Connections 0x09 |
| #define HCI_ERR_Max_Number_Of_SCO_Connections_To_A_Device 0x0A |
| #define HCI_ERR_ACL_Connection_Already_Exists 0x0B |
| #define HCI_ERR_Command_Disallowed 0x0C |
| #define HCI_ERR_Host_Rejected_Due_To_Limited_Resources 0x0D |
| #define HCI_ERR_Host_Rejected_Due_To_Security_Reasons 0x0E |
| #define HCI_ERR_Host_Rejected_Due_To_A_Remote_Device_Only_A_Personal_Device 0x0F |
| #define HCI_ERR_Host_Timeout 0x10 |
| #define HCI_ERR_Unsupported_Feature_Or_Parameter_Value 0x11 |
| #define HCI_ERR_Invalid_HCI_Command_Parameters 0x12 |
| #define HCI_ERR_Other_End_Terminated_Connection_User_Ended_Connection 0x13 |
| #define HCI_ERR_Other_End_Terminated_Connection_Low_Resources 0x14 |
| #define HCI_ERR_Other_End_Terminated_Connection_About_To_Power_Off 0x15 |
| #define HCI_ERR_Connection_Terminated_By_Local_Host 0x16 |
| #define HCI_ERR_Repeated_Attempts 0x17 |
| #define HCI_ERR_Pairing_Not_Allowed 0x18 |
| #define HCI_ERR_Unknown_LMP_PDU 0x19 |
| #define HCI_ERR_Unsupported_Remote_Feature 0x1A |
| #define HCI_ERR_SCO_Offset_Rejected 0x1B |
| #define HCI_ERR_SCO_Interval_Rejected 0x1C |
| #define HCI_ERR_SCO_Air_Mode_Rejected 0x1D |
| #define HCI_ERR_Invalid_LMP_Parameters 0x1E |
| #define HCI_ERR_Unspecified_Error 0x1F |
| #define HCI_ERR_Unsupported_LMP_Parameter 0x20 |
| #define HCI_ERR_Role_Change_Not_Allowed 0x21 |
| #define HCI_ERR_LMP_Response_Timeout 0x22 |
| #define HCI_ERR_LMP_Error_Transaction_Collision 0x23 |
| #define HCI_ERR_LMP_PDU_Not_Allowed 0x24 |
| #define HCI_ERR_Encryption_Mode_Not_Acceptable 0x25 |
| #define HCI_ERR_Unit_Key_Used 0x26 |
| #define HCI_ERR_QoS_Not_Supported 0x27 |
| #define HCI_ERR_Instant_Passed 0x28 |
| #define HCI_ERR_Pairing_With_Unit_Key_Not_Supported 0x29 |
| |
| #endif |
