| /** | |
| * \file | |
| * | |
| * \brief User Interface | |
| * | |
| * Copyright (C) 2009 Atmel Corporation. All rights reserved. | |
| * | |
| * \page License | |
| * | |
| * Redistribution and use in source and binary forms, with or without | |
| * modification, are permitted provided that the following conditions are met: | |
| * | |
| * 1. Redistributions of source code must retain the above copyright notice, | |
| * this list of conditions and the following disclaimer. | |
| * | |
| * 2. Redistributions in binary form must reproduce the above copyright notice, | |
| * this list of conditions and the following disclaimer in the documentation | |
| * and/or other materials provided with the distribution. | |
| * | |
| * 3. The name of Atmel may not be used to endorse or promote products derived | |
| * from this software without specific prior written permission. | |
| * | |
| * 4. This software may only be redistributed and used in connection with an | |
| * Atmel AVR product. | |
| * | |
| * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED | |
| * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF | |
| * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE | |
| * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR | |
| * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
| * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
| * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
| * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT | |
| * LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY | |
| * OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH | |
| * DAMAGE. | |
| */ | |
| #include "compiler.h" | |
| #include "conf_usb.h" | |
| #include "board.h" | |
| #include "led.h" | |
| #include "communication_model.h" | |
| #include "ui.h" | |
| void ui_init(void) | |
| { | |
| LED_On(LEDUSB_GPIO); | |
| LED_Off(LED0_GPIO); | |
| LED_Off(LED1_GPIO); | |
| } | |
| void ui_powerdown(void) | |
| { | |
| LED_Off(LEDUSB_GPIO); | |
| LED_Off(LED0_GPIO); | |
| LED_Off(LED1_GPIO); | |
| LED_Off(LED2_GPIO); | |
| } | |
| void ui_wakeup(void) | |
| { | |
| LED_On(LEDUSB_GPIO); | |
| } | |
| void ui_association(bool b_on) | |
| { | |
| if (b_on) { | |
| LED_On(LED2_GPIO); | |
| } else { | |
| LED_Off(LED2_GPIO); | |
| } | |
| } | |
| void ui_process(uint16_t framenumber) | |
| { | |
| bool b_btn_state; | |
| static bool btn0_last_state = false; | |
| static bool btn1_last_state = false; | |
| static uint8_t cpt_sof = 0; | |
| if (0 == framenumber) { | |
| LED_On(LED0_GPIO); | |
| } | |
| if (1000 == framenumber) { | |
| LED_Off(LED0_GPIO); | |
| } | |
| cpt_sof++; | |
| if (20 > cpt_sof) | |
| return; | |
| cpt_sof = 0; | |
| // Scan buttons on switch 0 (left), 1 (middle), 2 (right) | |
| b_btn_state = gpio_pin_is_low(GPIO_PUSH_BUTTON_0); | |
| if (b_btn_state != btn0_last_state) { | |
| btn0_last_state = b_btn_state; | |
| if (b_btn_state) { | |
| ieee11073_com_model_send_measure_1(); | |
| } | |
| } | |
| b_btn_state = gpio_pin_is_low(GPIO_PUSH_BUTTON_1); | |
| if (b_btn_state != btn1_last_state) { | |
| btn1_last_state = b_btn_state; | |
| if (b_btn_state) { | |
| ieee11073_com_model_send_measure_2(); | |
| } | |
| } | |
| } | |
| /** | |
| * \defgroup UI User Iinterface | |
| * | |
| * Human interface on Xplain-A1: | |
| * - RED led close to USB connector is always on after firmware startup | |
| * - Led 0 is on when USB line is in IDLE mode, and off in SUSPEND mode | |
| * - Led 1 blinks when USB Host have checked and enabled PHDC interface | |
| * - Led 2 is on when PHDC has validated association | |
| */ |