blob: 4e7c96f6a24365f2dab71ad8a1d8619c8d9583b5 [file] [log] [blame]
Change Log & Release Notes
==========================
This document contains a summary of the new features, changes, fixes and known
issues in each release of Trusted Firmware-A.
Version 2.5
-----------
New Features
^^^^^^^^^^^^
- Architecture support
- Added support for speculation barrier(``FEAT_SB``) for non-Armv8.5
platforms starting from Armv8.0
- Added support for Activity Monitors Extension version 1.1(``FEAT_AMUv1p1``)
- Added helper functions for Random number generator(``FEAT_RNG``) registers
- Added support for Armv8.6 Multi-threaded PMU extensions (``FEAT_MTPMU``)
- Added support for MTE Asymmetric Fault Handling extensions(``FEAT_MTE3``)
- Added support for Privileged Access Never extensions(``FEAT_PANx``)
- Bootloader images
- Added PIE support for AArch32 builds
- Enable Trusted Random Number Generator service for BL32(sp_min)
- Build System
- Added build option for Arm Feature Modifiers
- Drivers
- Added support for interrupts in TZC-400 driver
- Broadcom
- Added support for I2C, MDIO and USB drivers
- Marvell
- Added support for secure read/write of dfc register-set
- Added support for thermal sensor driver
- Implement a3700_core_getc API in console driver
- Added rx training on 10G port
- Marvell Mochi
- Added support for cn913x in PCIe mode
- Marvell Armada A8K
- Added support for TRNG-IP-76 driver and accessing RNG register
- Mediatek MT8192
- Added support for following drivers
- MPU configuration for SCP/PCIe
- SPM suspend
- Vcore DVFS
- LPM
- PTP3
- UART save and restore
- Power-off
- PMIC
- CPU hotplug and MCDI support
- SPMC
- MPU
- Mediatek MT8195
- Added support for following drivers
- GPIO, NCDI, SPMC drivers
- Power-off
- CPU hotplug, reboot and MCDI
- Delay timer and sys timer
- GIC
- NXP
- Added support for
- non-volatile storage API
- chain of trust and trusted board boot using two modes: MBEDTLS and CSF
- fip-handler necessary for DDR initialization
- SMMU and console drivers
- crypto hardware accelerator driver
- following drivers: SD, EMMC, QSPI, FLEXSPI, GPIO, GIC, CSU, PMU, DDR
- NXP Security Monitor and SFP driver
- interconnect config APIs using ARM CCN-CCI driver
- TZC APIs to configure DDR region
- generic timer driver
- Device configuration driver
- IMX
- Added support for image loading and io-storage driver for TBBR fip booting
- Renesas
- Added support for PFC and EMMC driver
- RZ Family:
- G2N, G2E and G2H SoCs
- Added support for watchdog, QoS, PFC and DRAM initialization
- RZG Family:
- G2M
- Added support for QoS and DRAM initialization
- Xilinx
- Added JTAG DCC support for Versal and ZynqMP SoC family.
- Libraries
- C standard library
- Added support to print ``%`` in ``snprintf()`` and ``printf()`` APIs
- Added support for strtoull, strtoll, strtoul, strtol APIs from FreeBSD project
- CPU support
- Added support for
- Cortex_A78C CPU
- Makalu ELP CPU
- Makalu CPU
- Matterhorn CPU
- Neoverse-N2 CPU
- CPU Errata
- Arm Cortex-A76: Added workaround for erratum 1946160
- Arm Cortex-A77: Added workaround for erratum 1946167
- Arm Cortex-A78: Added workaround for erratum 1941498 and 1951500
- Arm Neoverse-N1: Added workaround for erratum 1946160
- Flattened device tree(libfdt)
- Added support for wrapper function to read UUIDs in string format from dtb
- Platforms
- Added support for MediaTek MT8195
- Added support for Arm RD-N2 board
- Allwinner
- Added support for H616 SoC
- Arm
- Added support for GPT parser
- Protect GICR frames for fused/unused cores
- Arm Morello
- Added VirtIO network device to Morello FVP fdts
- Arm RD-N2
- Added support for variant 1 of RD-N2 platform
- Enable AMU support
- Arm RD-V1
- Enable AMU support
- Arm SGI
- Added support for platform variant build option
- Arm TC0
- Added Matterhorn ELP CPU support
- Added support for opteed
- Arm Juno
- Added support to use hw_config in BL31
- Use TRNG entropy source for SMCCC TRNG interface
- Condition Juno entropy source with CRC instructions
- Marvell Mochi
- Added support for detection of secure mode
- Marvell ARMADA
- Added support for new compile option A3720_DB_PM_WAKEUP_SRC
- Added support doing system reset via CM3 secure coprocessor
- Made several makefile enhancements required to build WTMI_MULTI_IMG and TIMDDRTOOL
- Added support for building DOIMAGETOOL tool
- Added new target mrvl_bootimage
- Mediatek MT8192
- Added support for rtc power off sequence
- Mediatek MT8195
- Added support for SiP service
- STM32MP1
- Added support for
- Seeed ODYSSEY SoM and board
- SDMMC2 and I2C2 pins in pinctrl
- I2C2 peripheral in DTS
- PIE for BL32
- TZC-400 interrupt managament
- Linux Automation MC-1 board
- Renesas RZG
- Added support for identifying EK874 RZ/G2E board
- Added support for identifying HopeRun HiHope RZ/G2H and RZ/G2H boards
- Rockchip
- Added support for stack protector
- QEMU
- Added support for ``max`` CPU
- Added Cortex-A72 support to ``virt`` platform
- Enabled trigger reboot from secure pl061
- QEMU SBSA
- Added support for sbsa-ref Embedded Controller
- NXP
- Added support for warm reset to retain ddr content
- Added support for image loader necessary for loading fip image
- lx2160a SoC Family
- Added support for
- new platform lx2160a-aqds
- new platform lx2160a-rdb
- new platform lx2162a-aqds
- errata handling
- IMX imx8mm
- Added support for trusted board boot
- TI K3
- Added support for lite device board
- Enabled Cortex-A72 erratum 1319367
- Enabled Cortex-A53 erratum 1530924
- Xilinx ZynqMP
- Added support for PS and system reset on WDT restart
- Added support for error management
- Enable support for log messages necessary for debug
- Added support for PM API SMC call for efuse and register access
- Processes
- Introduced process for platform deprecation
- Added documentation for TF-A threat model
- Provided a copy of the MIT license to comply with the license
requirements of the arm-gic.h source file (originating from the Linux
kernel project and re-distributed in TF-A).
- Services
- Added support for TRNG firmware interface service
- Arm
- Added SiP service to configure Ethos-N NPU
- SPMC
- Added documentation for SPM(Hafnium) SMMUv3 driver
- SPMD
- Added support for
- FFA_INTERRUPT forwading ABI
- FFA_SECONDARY_EP_REGISTER ABI
- FF-A v1.0 boot time power management, SPMC secondary core boot and
early run-time power management
- Tools
- FIPTool
- Added mechanism to allow platform specific image UUID
- git hooks
- Added support for conventional commits through commitlint hook,
commitizen hook and husky configuration files.
- NXP tool
- Added support for a tool that creates pbl file from BL2
- Renesas RZ/G2
- Added tool support for creating bootparam and cert_header images
- CertCreate
- Added support for platform-defined certificates, keys, and extensions using
the platform's makefile
- shared tools
- Added EFI_GUID representation to uuid helper data structure
Changed
^^^^^^^
- Common components
- Print newline after hex address in aarch64 el3_panic function
- Use proper ``#address-cells`` and ``#size-cells`` for reserved-memory in dtbs
- Drivers
- Move SCMI driver from ST platform directory and make it common to all platforms
- Arm GICv3
- Shift eSPI register offset in GICD_OFFSET_64()
- Use mpidr to probe GICR for current CPU
- Arm TZC-400
- Adjust filter tag if it set to FILTER_BIT_ALL
- Cadence
- Enhance UART driver APIs to put characters to fifo
- Mediatek MT8192
- Move timer driver to common folder
- Enhanced sys_cirq driver to add more IC services
- Renesas
- Move ddr and delay driver to common directory
- Renesas rcar
- Treat log as device memory in console driver
- Renesas RZ Family:
- G2N and G2H SoCs
- Select MMC_CH1 for eMMC channel
- Marvell
- Added support for checking if TRNG unit is present
- Marvell A3K
- Set TXDCLK_2X_SEL bit during PCIe initialization
- Set mask parameter for every reg_set call
- Marvell Mochi
- Added missing stream IDs configurations
- MbedTLS
- Migrated to Mbed TLS v2.26.0
- IMX imx8mp
- Change the bl31 physical load address
- QEMU SBSA
- Enable secure variable storage
- SCMI
- Update power domain protocol version to 2.0
- STM32
- Remove dead code from nand FMC driver
- Libraries
- C Standard Library
- Use macros to reduce duplicated code between snprintf and printf
- CPU support
- Sanity check pointers before use in AArch32 builds
- Arm Cortex-A78
- Remove rainier cpu workaround for errata 1542319
- Arm Makalu ELP
- Added "_arm" suffix to Makalu ELP CPU lib
- Miscellaneous
- Editorconfig
- set max line length to 100
- Platforms
- Allwinner
- Added reserved-memory node to DT
- Express memmap more dynamically
- Move SEPARATE_NOBITS_REGION to platforms
- Limit FDT checks to reduce code size
- Use CPUIDLE hardware when available
- Allow conditional compilation of SCPI and native PSCI ops
- Always use a 3MHz RSB bus clock
- Enable workaround for Cortex-A53 erratum 1530924
- Fixed non-default PRELOADED_BL33_BASE
- Leave CPU power alone during BL31 setup
- Added several psci hooks enhancements to improve system shutdown/reset
sequence
- Return the PMIC to I2C mode after use
- Separate code to power off self and other CPUs
- Split native and SCPI-based PSCI implementations
- Allwinner H6
- Added R_PRCM security setup for H6 board
- Added SPC security setup for H6 board
- Use RSB for the PMIC connection on H6
- Arm
- Store UUID as a string, rather than ints
- Replace FIP base and size macro with a generic name
- Move compile time switch from source to dt file
- Don't provide NT_FW_CONFIG when booting hafnium
- Do not setup 'disabled' regulator
- Increase SP max size
- Remove false dependency of ARM_LINUX_KERNEL_AS_BL33 on RESET_TO_BL31
and allow it to be enabled independently
- Arm FVP
- Do not map GIC region in BL1 and BL2
- Arm Juno
- Refactor juno_getentropy() to return 64 bits on each call
- Arm Morello
- Remove "virtio-rng" from Morello FVP
- Enable virtIO P9 device for Morello fvp
- Arm RDV1
- Allow all PSCI callbacks on RD-V1
- Rename rddaniel to rdv1
- Arm RDV1MC
- Rename rddanielxlr to rdv1mc
- Initialize TZC-400 controllers
- Arm TC0
- Updated GICR base address
- Use scmi_dvfs clock index 1 for cores 4-7 through fdt
- Added reserved-memory node for OP-TEE fdts
- Enabled Theodul DSU in TC platform
- OP-TEE as S-EL1 SP with SPMC at S-EL2
- Update Matterhorm ELP DVFS clock index
- Arm SGI
- Allow access to TZC controller on all chips
- Define memory regions for multi-chip platforms
- Allow access to nor2 flash and system registers from S-EL0
- Define default list of memory regions for DMC-620 TZC
- Improve macros defining cper buffer memory region
- Refactor DMC-620 error handling SMC function id
- Refactor SDEI specific macros
- Added platform id value for RDN2 platform
- Refactored header file inclusions and inclusion of memory mapping
- Arm RDN2
- Allow usage of secure partitions on RDN2 platform
- Update GIC redistributor and TZC base address
- Arm SGM775
- Deprecate Arm sgm775 FVP platform
- Marvell
- Increase TX FIFO EMPTY timeout from 2ms to 3ms
- Update delay code to be compatible with 1200 MHz CPU
- Marvell ARMADA
- Postpone MSS CPU startup to BL31 stage
- Allow builds without MSS support
- Use MSS SRAM in secure mode
- Added missing FORCE, .PHONY and clean targets
- Cleanup MSS SRAM if used for copy
- Move definition of mrvl_flash target to common marvell_common.mk file
- Show informative build messages and blank lines
- Marvell ARMADA A3K
- Added a new target mrvl_uart which builds UART image
- Added checks that WTP, MV_DDR_PATH and CRYPTOPP_PATH are correctly defined
- Allow use of the system Crypto++ library
- Build $(WTMI_ENC_IMG) in $(BUILD_PLAT) directory
- Build intermediate files in $(BUILD_PLAT) directory
- Build UART image files directly in $(BUILD_UART) subdirectory
- Correctly set DDR_TOPOLOGY and CLOCKSPRESET for WTMI
- Do not use 'echo -e' in Makefile
- Improve 4GB DRAM usage from 3.375 GB to 3.75 GB
- Remove unused variable WTMI_SYSINIT_IMG from Makefile
- Simplify check if WTP variable is defined
- Split building $(WTMI_MULTI_IMG) and $(TIMDDRTOOL)
- Marvell ARMADA A8K
- Allow CP1/CP2 mapping at BLE stage
- Mediatek MT8183
- Added timer V20 compensation
- Nvidia Tegra
- Rename SMC API
- TI K3
- Make plat_get_syscnt_freq2 helper check CNT_FID0 register
- Fill non-message data fields in sec_proxy with 0x0
- Update ti_sci_msg_req_reboot ABI to include domain
- Enable USE_COHERENT_MEM only for the generic board
- Explicitly map SEC_SRAM_BASE to 0x0
- Use BL31_SIZE instead of computing
- Define the correct number of max table entries and increase SRAM size
to account for additional table
- Raspberry Pi4
- Switch to gicv2.mk and GICV2_SOURCES
- Renesas
- Move headers and assembly files to common folder
- Renesas rzg
- Added device tree memory node enhancements
- Rockchip
- Switch to using common gicv3.mk
- STM32MP1
- Set BL sizes regardless of flags
- QEMU
- Include gicv2.mk for compiling GICv2 source files
- Change DEVICE2 definition for MMU
- Added helper to calculate the position shift from MPIDR
- QEMU SBSA
- Include libraries for Cortex-A72
- Increase SHARED_RAM_SIZE
- Addes support in spm_mm for upto 512 cores
- Added support for topology handling
- QTI
- Mandate SMC implementation
- Xilinx
- Rename the IPI CRC checksum macro
- Use fno-jump-tables flag in CPPFLAGS
- Xilinx versal
- Added the IPI CRC checksum macro support
- Mark IPI calls secure/non-secure
- Enable sgi to communicate with linux using IPI
- Remove Cortex-A53 compilation
- Xilinx ZynqMP
- Configure counter frequency during initialization
- Filter errors related to clock gate permissions
- Implement pinctrl request/release EEMI API
- Reimplement pinctrl get/set config parameter EEMI API calls
- Reimplement pinctrl set/get function EEMI API
- Update error codes to match Linux and PMU Firmware
- Update PM version and support PM version check
- Update return type in query functions
- Added missing ids for 43/46/47dr devices
- Checked for DLL status before doing reset
- Disable ITAPDLYENA bit for zero ITAP delay
- Include GICv2 makefile
- Remove the custom crash implementation
- Services
- SPMD
- Lock the g_spmd_pm structure
- Declare third cactus instance as UP SP
- Provide number of vCPUs and VM size for first SP
- Remove ``chosen`` node from SPMC manifests
- Move OP-TEE SP manifest DTS to FVP platform
- Update OP-TEE SP manifest with device-regions node
- Remove device-memory node from SPMC manifests
- SPM_MM
- Use sp_boot_info to set SP context
- SDEI
- Updata the affinity of shared event
- Tools
- FIPtool
- Do not print duplicate verbose lines about building fiptool
- CertCreate
- Updated tool for platform defined certs, keys & extensions
- Create only requested certificates
- Avoid duplicates in extension stack
Resolved Issues
^^^^^^^^^^^^^^^
- Several fixes for typos and mis-spellings in documentation
- Build system
- Fixed ${FIP_NAME} to be rebuilt only when needed in Makefile
- Do not mark file targets as .PHONY target in Makefile
- Drivers
- Authorization
- Avoid NV counter upgrade without certificate validation
- Arm GICv3
- Fixed logical issue for num_eints
- Limit SPI ID to avoid misjudgement in GICD_OFFSET()
- Fixed potential GICD context override with ESPI enabled
- Marvell A3700
- Fixed configuring polarity invert bits
- Arm TZC-400
- Correct FAIL_CONTROL Privileged bit
- Fixed logical error in FILTER_BIT definitions
- Renesas rcar
- Fixed several coding style violations reported by checkpatch
- Libraries
- Arch helpers
- Fixed assertions in processing dynamic relocations for AArch64 builds
- C standard library
- Fixed MISRA issues in memset() ABI
- RAS
- Fixed bug of binary search in RAS interrupt handler
- Platforms
- Arm
- Fixed missing copyrights in arm-gic.h file
- Fixed the order of header files in several dts files
- Fixed error message printing in board makefile
- Fixed bug of overriding the last node in image load helper API
- Fixed stdout-path in fdts files of TC0 and N1SDP platforms
- Turn ON/OFF redistributor in sync with GIC CPU interface ON/OFF for css platforms
- Arm FVP
- Fixed Generic Timer interrupt types in platform dts files
- Arm Juno
- Fixed parallel build issue for romlib config
- Arm SGI
- Fixed bug in SDEI receive event of RAS handler
- Intel Agilex
- Fixed PLAT_MAX_PWR_LVL value
- Marvell
- Fixed SPD handling in dram port
- Marvell ARMADA
- Fixed TRNG return SMC handling
- Fixed the logic used for LD selector mask
- Fixed MSS firmware loader for A8K family
- ST
- Fixed few violations reported by coverity static checks
- STM32MP1
- Fixed SELFREF_TO_X32 mask in ddr driver
- Do not keep mmc_device_info in stack
- Correct plat_crash_console_flush()
- QEMU SBSA
- Fixed memory type of secure NOR flash
- QTI
- Fixed NUM_APID and REG_APID_MAP() argument in SPMI driver
- Intel
- Do not keep mmc_device_info in stack
- Hisilicon
- Do not keep mmc_device_info in stack
- Services
- EL3 runtime
- Fixed the EL2 context save/restore routine by removing EL2 generic
timer system registers
- Added fix for exception handler in BL31 by synchronizing pending EA
using DSB barrier
- SPMD
- Fixed error codes to use int32_t type
- TSPD
- Added bug fix in tspd interrupt handling when TSP_NS_INTR_ASYNC_PREEMPT is enabled
- TRNG
- Fixed compilation errors with -O0 compile option
- DebugFS
- Checked channel index before calling clone function
- PSCI
- Fixed limit of 256 CPUs caused by cast to unsigned char
- TSP
- Fixed compilation erros when built with GCC 11.0.0 toolchain
- Tools
- FIPtool
- Do not call ``make clean`` for ``all`` target
- CertCreate
- Fixed bug to avoid cleaning when building the binary
- Used preallocated parts of the HASH struct to avoid leaking HASH struct fields
- Free arguments copied with strdup
- Free keys after use
- Free X509_EXTENSION structures on stack to avoid leaking them
- Optimized the code to avoid unnecessary attempts to create non-requested
certificates
Version 2.4
-----------
New Features
^^^^^^^^^^^^
- Architecture support
- Armv8.6-A
- Added support for Armv8.6 Enhanced Counter Virtualization (ECV)
- Added support for Armv8.6 Fine Grained Traps (FGT)
- Added support for Armv8.6 WFE trap delays
- Bootloader images
- Added support for Measured Boot
- Build System
- Added build option ``COT_DESC_IN_DTB`` to create Chain of Trust at runtime
- Added build option ``OPENSSL_DIR`` to direct tools to OpenSSL libraries
- Added build option ``RAS_TRAP_LOWER_EL_ERR_ACCESS`` to enable trapping RAS
register accesses from EL1/EL2 to EL3
- Extended build option ``BRANCH_PROTECTION`` to support branch target
identification
- Common components
- Added support for exporting CPU nodes to the device tree
- Added support for single and dual-root Chains of Trust in secure
partitions
- Drivers
- Added Broadcom RNG driver
- Added Marvell ``mg_conf_cm3`` driver
- Added System Control and Management Interface (SCMI) driver
- Added STMicroelectronics ETZPC driver
- Arm GICv3
- Added support for detecting topology at runtime
- Dual Root
- Added support for platform certificates
- Marvell Cache LLC
- Added support for mapping the entire LLC into SRAM
- Marvell CCU
- Added workaround for erratum 3033912
- Marvell CP110 COMPHY
- Added support for SATA COMPHY polarity inversion
- Added support for USB COMPHY polarity inversion
- Added workaround for erratum IPCE_COMPHY-1353
- STM32MP1 Clocks
- Added ``RTC`` as a gateable clock
- Added support for shifted clock selector bit masks
- Added support for using additional clocks as parents
- Libraries
- C standard library
- Added support for hexadecimal and pointer format specifiers in
``snprint()``
- Added assembly alternatives for various library functions
- CPU support
- Arm Cortex-A53
- Added workaround for erratum 1530924
- Arm Cortex-A55
- Added workaround for erratum 1530923
- Arm Cortex-A57
- Added workaround for erratum 1319537
- Arm Cortex-A76
- Added workaround for erratum 1165522
- Added workaround for erratum 1791580
- Added workaround for erratum 1868343
- Arm Cortex-A72
- Added workaround for erratum 1319367
- Arm Cortex-A77
- Added workaround for erratum 1508412
- Added workaround for erratum 1800714
- Added workaround for erratum 1925769
- Arm Neoverse-N1
- Added workaround for erratum 1868343
- EL3 Runtime
- Added support for saving/restoring registers related to nested
virtualization in EL2 context switches if the architecture supports it
- FCONF
- Added support for Measured Boot
- Added support for populating Chain of Trust properties
- Added support for loading the ``fw_config`` image
- Measured Boot
- Added support for event logging
- Platforms
- Added support for Arm Morello
- Added support for Arm TC0
- Added support for iEi PUZZLE-M801
- Added support for Marvell OCTEON TX2 T9130
- Added support for MediaTek MT8192
- Added support for NXP i.MX 8M Nano
- Added support for NXP i.MX 8M Plus
- Added support for QTI CHIP SC7180
- Added support for STM32MP151F
- Added support for STM32MP153F
- Added support for STM32MP157F
- Added support for STM32MP151D
- Added support for STM32MP153D
- Added support for STM32MP157D
- Arm
- Added support for platform-owned SPs
- Added support for resetting to BL31
- Arm FPGA
- Added support for Klein
- Added support for Matterhorn
- Added support for additional CPU clusters
- Arm FVP
- Added support for performing SDEI platform setup at runtime
- Added support for SMCCC's ``SMCCC_ARCH_SOC_ID`` command
- Added an ``id`` field under the NV-counter node in the device tree to
differentiate between trusted and non-trusted NV-counters
- Added support for extracting the clock frequency from the timer node
in the device tree
- Arm Juno
- Added support for SMCCC's ``SMCCC_ARCH_SOC_ID`` command
- Arm N1SDP
- Added support for cross-chip PCI-e
- Marvell
- Added support for AVS reduction
- Marvell ARMADA
- Added support for twin-die combined memory device
- Marvell ARMADA A8K
- Added support for DDR with 32-bit bus width (both ECC and non-ECC)
- Marvell AP806
- Added workaround for erratum FE-4265711
- Marvell AP807
- Added workaround for erratum 3033912
- Nvidia Tegra
- Added debug printouts indicating SC7 entry sequence completion
- Added support for SDEI
- Added support for stack protection
- Added support for GICv3
- Added support for SMCCC's ``SMCCC_ARCH_SOC_ID`` command
- Nvidia Tegra194
- Added support for RAS exception handling
- Added support for SPM
- NXP i.MX
- Added support for SDEI
- QEMU SBSA
- Added support for the Secure Partition Manager
- QTI
- Added RNG driver
- Added SPMI PMIC arbitrator driver
- Added support for SMCCC's ``SMCCC_ARCH_SOC_ID`` command
- STM32MP1
- Added support for exposing peripheral interfaces to the non-secure
world at runtime
- Added support for SCMI clock and reset services
- Added support for STM32MP15x CPU revision Z
- Added support for SMCCC services in ``SP_MIN``
- Services
- Secure Payload Dispatcher
- Added a provision to allow clients to retrieve the service UUID
- SPMC
- Added secondary core endpoint information to the SPMC context
structure
- SPMD
- Added support for booting OP-TEE as a guest S-EL1 Secure Partition on
top of Hafnium in S-EL2
- Added a provision for handling SPMC messages to register secondary
core entry points
- Added support for power management operations
- Tools
- CertCreate
- Added support for secure partitions
- CertTool
- Added support for the ``fw_config`` image
- FIPTool
- Added support for the ``fw_config`` image
Changed
^^^^^^^
- Architecture support
- Bootloader images
- Build System
- The top-level Makefile now supports building FipTool on Windows
- The default value of ``KEY_SIZE`` has been changed to to 2048 when RSA is
in use
- The previously-deprecated macro ``__ASSEMBLY__`` has now been removed
- Common components
- Certain functions that flush the console will no longer return error
information
- Drivers
- Arm GIC
- Usage of ``drivers/arm/gic/common/gic_common.c`` has now been
deprecated in favour of ``drivers/arm/gic/vX/gicvX.mk``
- Added support for detecting the presence of a GIC600-AE
- Added support for detecting the presence of a GIC-Clayton
- Marvell MCI
- Now performs link tuning for all MCI interfaces to improve performance
- Marvell MoChi
- PIDI masters are no longer forced into a non-secure access level when
``LLC_SRAM`` is enabled
- The SD/MMC controllers are now accessible from guest virtual machines
- Mbed TLS
- Migrated to Mbed TLS v2.24.0
- STM32 FMC2 NAND
- Adjusted FMC node bindings to include an EBI controller node
- STM32 Reset
- Added an optional timeout argument to assertion functions
- STM32MP1 Clocks
- Enabled several additional system clocks during initialization
- Libraries
- C Standard Library
- Improved ``memset`` performance by avoiding single-byte writes
- Added optimized assembly variants of ``memset``
- CPU support
- Renamed Cortex-Hercules to Cortex-A78
- Renamed Cortex-Hercules AE to Cortex-A78 AE
- Renamed Neoverse Zeus to Neoverse V1
- Coreboot
- Updated ‘coreboot_get_memory_type’ API to take an extra argument as a
’memory size’ that used to return a valid memory type.
- libfdt
- Updated to latest upstream version
- Platforms
- Allwinner
- Disabled non-secure access to PRCM power control registers
- Arm
- ``BL32_BASE`` is now platform-dependent when ``SPD_spmd`` is enabled
- Added support for loading the Chain of Trust from the device tree
- The firmware update check is now executed only once
- NV-counter base addresses are now loaded from the device tree when
``COT_DESC_IN_DTB`` is enabled
- Now loads and populates ``fw_config`` and ``tb_fw_config``
- FCONF population now occurs after caches have been enabled in order
to reduce boot times
- Arm Corstone-700
- Platform support has been split into both an FVP and an FPGA variant
- Arm FPGA
- DTB and BL33 load addresses have been given sensible default values
- Now reads generic timer counter frequency, GICD and GICR base
addresses, and UART address from DT
- Now treats the primary PL011 UART as an SBSA Generic UART
- Arm FVP
- Secure interrupt descriptions, UART parameters, clock frequencies and
GICv3 parameters are now queried through FCONF
- UART parameters are now queried through the device tree
- Added an owner field to Cactus secure partitions
- Increased the maximum size of BL2 when the Chain of Trust is loaded
from the device tree
- Reduces the maximum size of BL31
- The ``FVP_USE_SP804_TIMER`` and ``FVP_VE_USE_SP804_TIMER`` build
options have been removed in favour of a common ``USE_SP804_TIMER``
option
- Added a third Cactus partition to manifests
- Device tree nodes now store UUIDs in big-endian
- Arm Juno
- Increased the maximum size of BL2 when optimizations have not been
applied
- Reduced the maximum size of BL31 and BL32
- Marvell AP807
- Enabled snoop filters
- Marvell ARMADA A3K
- UART recovery images are now suffixed with ``.bin``
- Marvell ARMADA A8K
- Option ``BL31_CACHE_DISABLE`` is now disabled (``0``) by default
- Nvidia Tegra
- Added VPR resize supported check when processing video memory resize
requests
- Added SMMU verification to prevent potential issues caused by
undetected corruption of the SMMU configuration during boot
- The GIC CPU interface is now properly disabled after CPU off
- The GICv2 sources list and the ``BL31_SIZE`` definition have been made
platform-specific
- The SPE driver will no longer flush the console when writing
individual characters
- Nvidia Tegra194
- TZDRAM setup has been moved to platform-specific early boot handlers
- Increased verbosity of debug prints for RAS SErrors
- Support for powering down CPUs during CPU suspend has been removed
- Now verifies firewall settings before using resources
- TI K3
- The UART number has been made configurable through ``K3_USART``
- Rockchip RK3368
- The maximum number of memory map regions has been increased to 20
- Socionext Uniphier
- The maximum size of BL33 has been increased to support larger
bootloaders
- STM32
- Removed platform-specific DT functions in favour of using existing
generic alternatives
- STM32MP1
- Increased verbosity of exception reports in debug builds
- Device trees have been updated to align with the Linux kernel
- Now uses the ETZPC driver to configure secure-aware interfaces for
assignment to the non-secure world
- Finished good variants have been added to the board identifier
enumerations
- Non-secure access to clocks and reset domains now depends on their
state of registration
- NEON is now disabled in ``SP_MIN``
- The last page of ``SYSRAM`` is now used as SCMI shared memory
- Checks to verify platform compatibility have been added to verify that
an image is compatible with the chip ID of the running platform
- QEMU SBSA
- Removed support for Arm's Cortex-A53
- Services
- Renamed SPCI to FF-A
- SPMD
- No longer forwards requests to the non-secure world when retrieving
partition information
- SPMC manifest size is now retrieved directly from SPMD instead of the
device tree
- The FF-A version handler now returns SPMD's version when the origin
of the call is secure, and SPMC's version when the origin of the call
is non-secure
- SPMC
- Updated the manifest to declare CPU nodes in descending order as per
the SPM (Hafnium) multicore requirement
- Updated the device tree to mark 2GB as device memory for the first
partition excluding trusted DRAM region (which is reserved for SPMC)
- Increased the number of EC contexts to the maximum number of PEs as
per the FF-A specification
- Tools
- FIPTool
- Now returns ``0`` on ``help`` and ``help <command>``
- Marvell DoImage
- Updated Mbed TLS support to v2.8
- SPTool
- Now appends CertTool arguments
Resolved Issues
^^^^^^^^^^^^^^^
- Bootloader images
- Fixed compilation errors for dual-root Chains of Trust caused by symbol
collision
- BL31
- Fixed compilation errors on platforms with fewer than 4 cores caused
by initialization code exceeding the end of the stacks
- Fixed compilation errors when building a position-independent image
- Build System
- Fixed invalid empty version strings
- Fixed compilation errors on Windows caused by a non-portable architecture
revision comparison
- Drivers
- Arm GIC
- Fixed spurious interrupts caused by a missing barrier
- STM32 Flexible Memory Controller 2 (FMC2) NAND driver
- Fixed runtime instability caused by incorrect error detection logic
- STM32MP1 Clock driver
- Fixed incorrectly-formatted log messages
- Fixed runtime instability caused by improper clock gating procedures
- STMicroelectronics Raw NAND driver
- Fixed runtime instability caused by incorrect unit conversion when
waiting for NAND readiness
- Libraries
- AMU
- Fixed timeout errors caused by excess error logging
- EL3 Runtime
- Fixed runtime instability caused by improper register save/restore
routine in EL2
- FCONF
- Fixed failure to initialize GICv3 caused by overly-strict device tree
requirements
- Measured Boot
- Fixed driver errors caused by a missing default value for the
``HASH_ALG`` build option
- SPE
- Fixed feature detection check that prevented CPUs supporting SVE from
detecting support for SPE in the non-secure world
- Translation Tables
- Fixed various MISRA-C 2012 static analysis violations
- Platforms
- Allwinner A64
- Fixed USB issues on certain battery-powered device caused by
improperly activated USB power rail
- Arm
- Fixed compilation errors caused by increase in BL2 size
- Fixed compilation errors caused by missing Makefile dependencies to
generated files when building the FIP
- Fixed MISRA-C 2012 static analysis violations caused by unused
structures in include directives intended to be feature-gated
- Arm FPGA
- Fixed initialization issues caused by incorrect MPIDR topology mapping
logic
- Arm RD-N1-edge
- Fixed compilation errors caused by mismatched parentheses in Makefile
- Arm SGI
- Fixed crashes due to the flash memory used for cold reboot attack
protection not being mapped
- Intel Agilex
- Fixed initialization issues caused by several compounding bugs
- Marvell
- Fixed compilation warnings caused by multiple Makefile inclusions
- Marvell ARMADA A3K
- Fixed boot issue in debug builds caused by checks on the BL33 load
address that are not appropriate for this platform
- Nvidia Tegra
- Fixed incorrect delay timer reads
- Fixed spurious interrupts in the non-secure world during cold boot
caused by the arbitration bit in the memory controller not being
cleared
- Fixed faulty video memory resize sequence
- Nvidia Tegra194
- Fixed incorrect alignment of TZDRAM base address
- NXP iMX8M
- Fixed CPU hot-plug issues caused by race condition
- STM32MP1
- Fixed compilation errors in highly-parallel builds caused by incorrect
Makefile dependencies
- STM32MP157C-ED1
- Fixed initialization issues caused by missing device tree hash node
- Raspberry Pi 3
- Fixed compilation errors caused by incorrect dependency ordering in
Makefile
- Rockchip
- Fixed initialization issues caused by non-critical errors when parsing
FDT being treated as critical
- Rockchip RK3368
- Fixed runtime instability caused by incorrect CPUID shift value
- QEMU
- Fixed compilation errors caused by incorrect dependency ordering in
Makefile
- QEMU SBSA
- Fixed initialization issues caused by FDT exceeding reserved memory
size
- QTI
- Fixed compilation errors caused by inclusion of a non-existent file
- Services
- FF-A (previously SPCI)
- Fixed SPMD aborts caused by incorrect behaviour when the manifest is
page-aligned
- Tools
- Fixed compilation issues when compiling tools from within their respective
directories
- FIPTool
- Fixed command line parsing issues on Windows when using arguments
whose names also happen to be a subset of another's
- Marvell DoImage
- Fixed PKCS signature verification errors at boot on some platforms
caused by generation of misaligned images
Known Issues
^^^^^^^^^^^^
- Platforms
- NVIDIA Tegra
- Signed comparison compiler warnings occurring in libfdt are currently
being worked around by disabling the warning for the platform until
the underlying issue is resolved in libfdt
Version 2.3
-----------
New Features
^^^^^^^^^^^^
- Arm Architecture
- Add support for Armv8.4-SecEL2 extension through the SPCI defined SPMD/SPMC
components.
- Build option to support EL2 context save and restore in the secure world
(CTX_INCLUDE_EL2_REGS).
- Add support for SMCCC v1.2 (introducing the new SMCCC_ARCH_SOC_ID SMC).
Note that the support is compliant, but the SVE registers save/restore will
be done as part of future S-EL2/SPM development.
- BL-specific
- Enhanced BL2 bootloader flow to load secure partitions based on firmware
configuration data (fconf).
- Changes necessary to support SEPARATE_NOBITS_REGION feature
- TSP and BL2_AT_EL3: Add Position Independent Execution ``PIE`` support
- Build System
- Add support for documentation build as a target in Makefile
- Add ``COT`` build option to select the Chain of Trust to use when the
Trusted Boot feature is enabled (default: ``tbbr``).
- Added creation and injection of secure partition packages into the FIP.
- Build option to support SPMC component loading and run at S-EL1
or S-EL2 (SPMD_SPM_AT_SEL2).
- Enable MTE support
- Enable Link Time Optimization in GCC
- Enable -Wredundant-decls warning check
- Makefile: Add support to optionally encrypt BL31 and BL32
- Add support to pass the nt_fw_config DTB to OP-TEE.
- Introduce per-BL ``CPPFLAGS``, ``ASFLAGS``, and ``LDFLAGS``
- build_macros: Add CREATE_SEQ function to generate sequence of numbers
- CPU Support
- cortex-a57: Enable higher performance non-cacheable load forwarding
- Hercules: Workaround for Errata 1688305
- Klein: Support added for Klein CPU
- Matterhorn: Support added for Matterhorn CPU
- Drivers
- auth: Add ``calc_hash`` function for hash calculation. Used for
authentication of images when measured boot is enabled.
- cryptocell: Add authenticated decryption framework, and support
for CryptoCell-713 and CryptoCell-712 RSA 3K
- gic600: Add support for multichip configuration and Clayton
- gicv3: Introduce makefile, Add extended PPI and SPI range,
Add support for probing multiple GIC Redistributor frames
- gicv4: Add GICv4 extension for GIC driver
- io: Add an IO abstraction layer to load encrypted firmwares
- mhu: Derive doorbell base address
- mtd: Add SPI-NOR, SPI-NAND, SPI-MEM, and raw NAND framework
- scmi: Allow use of multiple SCMI channels
- scu: Add a driver for snoop control unit
- Libraries
- coreboot: Add memory range parsing and use generic base address
- compiler_rt: Import popcountdi2.c and popcountsi2.c files,
aeabi_ldivmode.S file and dependencies
- debugFS: Add DebugFS functionality
- el3_runtime: Add support for enabling S-EL2
- fconf: Add Firmware Configuration Framework (fconf) (experimental).
- libc: Add memrchr function
- locks: bakery: Use is_dcache_enabled() helper and add a DMB to
the 'read_cache_op' macro
- psci: Add support to enable different personality of the same soc.
- xlat_tables_v2: Add support to pass shareability attribute for
normal memory region, use get_current_el_maybe_constant() in
is_dcache_enabled(), read-only xlat tables for BL31 memory, and
add enable_mmu()
- New Platforms Support
- arm/arm_fpga: New platform support added for FPGA
- arm/rddaniel: New platform support added for rd-daniel platform
- brcm/stingray: New platform support added for Broadcom stingray platform
- nvidia/tegra194: New platform support for Nvidia Tegra194 platform
- Platforms
- allwinner: Implement PSCI system suspend using SCPI, add a msgbox
driver for use with SCPI, and reserve and map space for the SCP firmware
- allwinner: axp: Add AXP805 support
- allwinner: power: Add DLDO4 power rail
- amlogic: axg: Add a build flag when using ATOS as BL32 and support for
the A113D (AXG) platform
- arm/a5ds: Add ethernet node and L2 cache node in devicetree
- arm/common: Add support for the new `dualroot` chain of trust
- arm/common: Add support for SEPARATE_NOBITS_REGION
- arm/common: Re-enable PIE when RESET_TO_BL31=1
- arm/common: Allow boards to specify second DRAM Base address
and to define PLAT_ARM_TZC_FILTERS
- arm/corstone700: Add support for mhuv2 and stack protector
- arm/fvp: Add support for fconf in BL31 and SP_MIN. Populate power
domain descriptor dynamically by leveraging fconf APIs.
- arm/fvp: Add Cactus/Ivy Secure Partition information and use two
instances of Cactus at S-EL1
- arm/fvp: Add support to run BL32 in TDRAM and BL31 in secure DRAM
- arm/fvp: Add support for GICv4 extension and BL2 hash calculation in BL1
- arm/n1sdp: Setup multichip gic routing table, update platform macros
for dual-chip setup, introduce platform information SDS region, add
support to update presence of External LLC, and enable the
NEOVERSE_N1_EXTERNAL_LLC flag
- arm/rdn1edge: Add support for dual-chip configuration and use
CREATE_SEQ helper macro to compare chip count
- arm/sgm: Always use SCMI for SGM platforms
- arm/sgm775: Add support for dynamic config using fconf
- arm/sgi: Add multi-chip mode parameter in HW_CONFIG dts, macros for
remote chip device region, chip_id and multi_chip_mode to platform
variant info, and introduce number of chips macro
- brcm: Add BL2 and BL31 support common across Broadcom platforms
- brcm: Add iproc SPI Nor flash support, spi driver, emmc driver,
and support to retrieve plat_toc_flags
- hisilicon: hikey960: Enable system power off callback
- intel: Enable bridge access, SiP SMC secure register access, and uboot
entrypoint support
- intel: Implement platform specific system reset 2
- intel: Introduce mailbox response length handling
- imx: console: Use CONSOLE_T_BASE for UART base address and generic console_t
data structure
- imx8mm: Provide uart base as build option and add the support for opteed spd
on imx8mq/imx8mm
- imx8qx: Provide debug uart num as build
- imx8qm: Apply clk/pinmux configuration for DEBUG_CONSOLE and provide debug
uart num as build param
- marvell: a8k: Implement platform specific power off and add support
for loading MG CM3 images
- mediatek: mt8183: Add Vmodem/Vcore DVS init level
- qemu: Support optional encryption of BL31 and BL32 images
and ARM_LINUX_KERNEL_AS_BL33 to pass FDT address
- qemu: Define ARMV7_SUPPORTS_VFP
- qemu: Implement PSCI_CPU_OFF and qemu_system_off via semihosting
- renesas: rcar_gen3: Add new board revision for M3ULCB
- rockchip: Enable workaround for erratum 855873, claim a macro to enable
hdcp feature for DP, enable power domains of rk3399 before reset, add
support for UART3 as serial output, and initialize reset and poweroff
GPIOs with known invalid value
- rpi: Implement PSCI CPU_OFF, use MMIO accessor, autodetect Mini-UART
vs. PL011 configuration, and allow using PL011 UART for RPi3/RPi4
- rpi3: Include GPIO driver in all BL stages and use same "clock-less"
setup scheme as RPi4
- rpi3/4: Add support for offlining CPUs
- st: stm32mp1: platform.mk: Support generating multiple images in one build,
migrate to implicit rules, derive map file name from target name, generate
linker script with fixed name, and use PHONY for the appropriate targets
- st: stm32mp1: Add support for SPI-NOR, raw NAND, and SPI-NAND boot device,
QSPI, FMC2 driver
- st: stm32mp1: Use stm32mp_get_ddr_ns_size() function, set XN attribute for
some areas in BL2, dynamically map DDR later and non-cacheable during its
test, add a function to get non-secure DDR size, add DT helper for reg by
name, and add compilation flags for boot devices
- socionext: uniphier: Turn on ENABLE_PIE
- ti: k3: Add PIE support
- xilinx: versal: Add set wakeup source, client wakeup, query data, request
wakeup, PM_INIT_FINALIZE, PM_GET_TRUSTZONE_VERSION, PM IOCTL, support for
suspend related, and Get_ChipID APIs
- xilinx: versal: Implement power down/restart related EEMI, SMC handler for
EEMI, PLL related PM, clock related PM, pin control related PM, reset related
PM, device related PM , APIs
- xilinx: versal: Enable ipi mailbox service
- xilinx: versal: Add get_api_version support and support to send PM API to PMC
using IPI
- xilinx: zynqmp: Add checksum support for IPI data, GET_CALLBACK_DATA
function, support to query max divisor, CLK_SET_RATE_PARENT in gem clock
node, support for custom type flags, LPD WDT clock to the pm_clock structure,
idcodes for new RFSoC silicons ZU48DR and ZU49DR, and id for new RFSoC device
ZU39DR
- Security
- Use Speculation Barrier instruction for v8.5+ cores
- Add support for optional firmware encryption feature (experimental).
- Introduce a new `dualroot` chain of trust.
- aarch64: Prevent speculative execution past ERET
- aarch32: Stop speculative execution past exception returns.
- SPCI
- Introduced the Secure Partition Manager Dispatcher (SPMD) component as a
new standard service.
- Tools
- cert_create: Introduce CoT build option and TBBR CoT makefile,
and define the dualroot CoT
- encrypt_fw: Add firmware authenticated encryption tool
- memory: Add show_memory script that prints a representation
of the memory layout for the latest build
Changed
^^^^^^^
- Arm Architecture
- PIE: Make call to GDT relocation fixup generalized
- BL-Specific
- Increase maximum size of BL2 image
- BL31: Discard .dynsym .dynstr .hash sections to make ENABLE_PIE work
- BL31: Split into two separate memory regions
- Unify BL linker scripts and reduce code duplication.
- Build System
- Changes to drive cert_create for dualroot CoT
- Enable -Wlogical-op always
- Enable -Wshadow always
- Refactor the warning flags
- PIE: Pass PIE options only to BL31
- Reduce space lost to object alignment
- Set lld as the default linker for Clang builds
- Remove -Wunused-const-variable and -Wpadded warning
- Remove -Wmissing-declarations warning from WARNING1 level
- Drivers
- authentication: Necessary fix in drivers to upgrade to mbedtls-2.18.0
- console: Integrate UART base address in generic console_t
- gicv3: Change API for GICR_IPRIORITYR accessors and separate
GICD and GICR accessor functions
- io: Change seek offset to signed long long and panic in case
of io setup failure
- smmu: SMMUv3: Changed retry loop to delay timer
- tbbr: Reduce size of hash and ECDSA key buffers when possible
- Library Code
- libc: Consolidate the size_t, unified, and NULL definitions,
and unify intmax_t and uintmax_t on AArch32/64
- ROMLIB: Optimize memory layout when ROMLIB is used
- xlat_tables_v2: Use ARRAY_SIZE in REGISTER_XLAT_CONTEXT_FULL_SPEC,
merge REGISTER_XLAT_CONTEXT_{FULL_SPEC,RO_BASE_TABLE},
and simplify end address checks in mmap_add_region_check()
- Platforms
- allwinner: Adjust SRAM A2 base to include the ARISC vectors, clean up MMU
setup, reenable USE_COHERENT_MEM, remove unused include path, move the
NOBITS region to SRAM A1, convert AXP803 regulator setup code into a driver,
enable clock before resetting I2C/RSB
- allwinner: h6: power: Switch to using the AXP driver
- allwinner: a64: power: Use fdt_for_each_subnode, remove obsolete register
check, remove duplicate DT check, and make sunxi_turn_off_soc static
- allwinner: Build PMIC bus drivers only in BL31, clean up PMIC-related error
handling, and synchronize PMIC enumerations
- arm/a5ds: Change boot address to point to DDR address
- arm/common: Check for out-of-bound accesses in the platform io policies
- arm/corstone700: Updating the kernel arguments to support initramfs,
use fdts DDR memory and XIP rootfs, and set UART clocks to 32MHz
- arm/fvp: Modify multithreaded dts file of DynamIQ FVPs, slightly bump
the stack size for bl1 and bl2, remove re-definition of topology related
build options, stop reclaiming init code with Clang builds, and map only
the needed DRAM region statically in BL31/SP_MIN
- arm/juno: Maximize space allocated to SCP_BL2
- arm/sgi: Bump bl1 RW limit, mark remote chip shared ram as non-cacheable,
move GIC related constants to board files, include AFF3 affinity in core
position calculation, move bl31_platform_setup to board file, and move
topology information to board folder
- common: Refactor load_auth_image_internal().
- hisilicon: Remove uefi-tools in hikey and hikey960 documentation
- intel: Modify non secure access function, BL31 address mapping, mailbox's
get_config_status, and stratix10 BL31 parameter handling
- intel: Remove un-needed checks for qspi driver r/w and s10 unused source code
- intel: Change all global sip function to static
- intel: Refactor common platform code
- intel: Create SiP service header file
- marvell: armada: scp_bl2: Allow loading up to 8 images
- marvell: comphy-a3700: Support SGMII COMPHY power off and fix USB3
powering on when on lane 2
- marvell: Consolidate console register calls
- mediatek: mt8183: Protect 4GB~8GB dram memory, refine GIC driver for
low power scenarios, and switch PLL/CLKSQ/ck_off/axi_26m control to SPM
- qemu: Update flash address map to keep FIP in secure FLASH0
- renesas: rcar_gen3: Update IPL and Secure Monitor Rev.2.0.6, update DDR
setting for H3, M3, M3N, change fixed destination address of BL31 and BL32,
add missing #{address,size}-cells into generated DT, pass DT to OpTee OS,
and move DDR drivers out of staging
- rockchip: Make miniloader ddr_parameter handling optional, cleanup securing
of ddr regions, move secure init to separate file, use base+size for secure
ddr regions, bring TZRAM_SIZE values in lined, and prevent macro expansion
in paths
- rpi: Move plat_helpers.S to common
- rpi3: gpio: Simplify GPIO setup
- rpi4: Skip UART initialisation
- st: stm32m1: Use generic console_t data structure, remove second
QSPI flash instance, update for FMC2 pin muxing, and reduce MAX_XLAT_TABLES
to 4
- socionext: uniphier: Make on-chip SRAM and I/O register regions configurable
- socionext: uniphier: Make PSCI related, counter control, UART, pinmon, NAND
controller, and eMMC controller base addresses configurable
- socionext: uniphier: Change block_addressing flag and the return value type
of .is_usb_boot() to bool
- socionext: uniphier: Run BL33 at EL2, call uniphier_scp_is_running() only
when on-chip STM is supported, define PLAT_XLAT_TABLES_DYNAMIC only for BL2,
support read-only xlat tables, use enable_mmu() in common function, shrink
UNIPHIER_ROM_REGION_SIZE, prepare uniphier_soc_info() for next SoC, extend
boot device detection for future SoCs, make all BL images completely
position-independent, make uniphier_mmap_setup() work with PIE, pass SCP
base address as a function parameter, set buffer offset and length for
io_block dynamically, and use more mmap_add_dynamic_region() for loading
images
- spd/trusty: Disable error messages seen during boot, allow gic base to be
specified with GICD_BASE, and allow getting trusty memsize from BL32_MEM_SIZE
instead of TSP_SEC_MEM_SIZE
- ti: k3: common: Enable ARM cluster power down and rename device IDs to
be more consistent
- ti: k3: drivers: ti_sci: Put sequence number in coherent memory and
remove indirect structure of const data
- xilinx: Move ipi mailbox svc to xilinx common
- xilinx: zynqmp: Use GIC framework for warm restart
- xilinx: zynqmp: pm: Move custom clock flags to typeflags, remove
CLK_TOPSW_LSBUS from invalid clock list and rename FPD WDT clock ID
- xilinx: versal: Increase OCM memory size for DEBUG builds and adjust
cpu clock, Move versal_def.h and versal_private to include directory
- Tools
- sptool: Updated sptool to accommodate building secure partition packages.
Resolved Issues
^^^^^^^^^^^^^^^
- Arm Architecture
- Fix crash dump for lower EL
- BL-Specific
- Bug fix: Protect TSP prints with lock
- Fix boot failures on some builds linked with ld.lld.
- Build System
- Fix clang build if CC is not in the path.
- Fix 'BL stage' comment for build macros
- Code Quality
- coverity: Fix various MISRA violations including null pointer violations,
C issues in BL1/BL2/BL31 and FDT helper functions, using boolean essential,
type, and removing unnecessary header file and comparisons to LONG_MAX in
debugfs devfip
- Based on coding guidelines, replace all `unsigned long` depending on if
fixed based on AArch32 or AArch64.
- Unify type of "cpu_idx" and Platform specific defines across PSCI module.
- Drivers
- auth: Necessary fix in drivers to upgrade to mbedtls-2.18.0
- delay_timer: Fix non-standard frequency issue in udelay
- gicv3: Fix compiler dependent behavior
- gic600: Fix include ordering according to the coding style and power up sequence
- Library Code
- el3_runtime: Fix stack pointer maintenance on EA handling path,
fixup 'cm_setup_context' prototype, and adds TPIDR_EL2 register
to the context save restore routines
- libc: Fix SIZE_MAX on AArch32
- locks: T589: Fix insufficient ordering guarantees in bakery lock
- pmf: Fix 'tautological-constant-compare' error, Make the runtime
instrumentation work on AArch32, and Simplify PMF helper macro
definitions across header files
- xlat_tables_v2: Fix assembler warning of PLAT_RO_XLAT_TABLES
- Platforms
- allwinner: Fix H6 GPIO and CCU memory map addresses and incorrect ARISC
code patch offset check
- arm/a5ds: Correct system freq and Cache Writeback Granule, and cleanup
enable-method in devicetree
- arm/fvp: Fix incorrect GIC mapping, BL31 load address and image size
for RESET_TO_BL31=1, topology description of cpus for DynamIQ based
FVP, and multithreaded FVP power domain tree
- arm/fvp: spm-mm: Correcting instructions to build SPM for FVP
- arm/common: Fix ROTPK hash generation for ECDSA encryption, BL2 bug in
dynamic configuration initialisation, and current RECLAIM_INIT_CODE behavior
- arm/rde1edge: Fix incorrect topology tree description
- arm/sgi: Fix the incorrect check for SCMI channel ID
- common: Flush dcache when storing timestamp
- intel: Fix UEFI decompression issue, memory calibration, SMC SIP service,
mailbox config return status, mailbox driver logic, FPGA manager on
reconfiguration, and mailbox send_cmd issue
- imx: Fix shift-overflow errors, the rdc memory region slot's offset,
multiple definition of ipc_handle, missing inclusion of cdefs.h, and
correct the SGIs that used for secure interrupt
- mediatek: mt8183: Fix AARCH64 init fail on CPU0
- rockchip: Fix definition of struct param_ddr_usage
- rpi4: Fix documentation of armstub config entry
- st: Correct io possible NULL pointer dereference and device_size type,
nand xor_ecc.val assigned value, static analysis tool issues, and fix
incorrect return value and correctly check pwr-regulators node
- xilinx: zynqmp: Correct syscnt freq for QEMU and fix clock models
and IDs of GEM-related clocks
Known Issues
^^^^^^^^^^^^
- Build System
- dtb: DTB creation not supported when building on a Windows host.
This step in the build process is skipped when running on a Windows host. A
known issue from the 1.6 release.
- Intermittent assertion firing `ASSERT: services/spd/tspd/tspd_main.c:105`
- Coverity
- Intermittent Race condition in Coverity Jenkins Build Job
- Platforms
- arm/juno: System suspend from Linux does not function as documented in the
user guide
Following the instructions provided in the user guide document does not
result in the platform entering system suspend state as expected. A message
relating to the hdlcd driver failing to suspend will be emitted on the
Linux terminal.
- mediatek/mt6795: This platform does not build in this release
Version 2.2
-----------
New Features
^^^^^^^^^^^^
- Architecture
- Enable Pointer Authentication (PAuth) support for Secure World
- Adds support for ARMv8.3-PAuth in BL1 SMC calls and
BL2U image for firmware updates.
- Enable Memory Tagging Extension (MTE) support in both secure and non-secure
worlds
- Adds support for the new Memory Tagging Extension arriving in
ARMv8.5. MTE support is now enabled by default on systems that
support it at EL0.
- To enable it at ELx for both the non-secure and the secure
world, the compiler flag ``CTX_INCLUDE_MTE_REGS`` includes register
saving and restoring when necessary in order to prevent information
leakage between the worlds.
- Add support for Branch Target Identification (BTI)
- Build System
- Modify FVP makefile for CPUs that support both AArch64/32
- AArch32: Allow compiling with soft-float toolchain
- Makefile: Add default warning flags
- Add Makefile check for PAuth and AArch64
- Add compile-time errors for HW_ASSISTED_COHERENCY flag
- Apply compile-time check for AArch64-only CPUs
- build_macros: Add mechanism to prevent bin generation.
- Add support for default stack-protector flag
- spd: opteed: Enable NS_TIMER_SWITCH
- plat/arm: Skip BL2U if RESET_TO_SP_MIN flag is set
- Add new build option to let each platform select which implementation of spinlocks
it wants to use
- CPU Support
- DSU: Workaround for erratum 798953 and 936184
- Neoverse N1: Force cacheable atomic to near atomic
- Neoverse N1: Workaround for erratum 1073348, 1130799, 1165347, 1207823,
1220197, 1257314, 1262606, 1262888, 1275112, 1315703, 1542419
- Neoverse Zeus: Apply the MSR SSBS instruction
- cortex-Hercules/HerculesAE: Support added for Cortex-Hercules and
Cortex-HerculesAE CPUs
- cortex-Hercules/HerculesAE: Enable AMU for Cortex-Hercules and Cortex-HerculesAE
- cortex-a76AE: Support added for Cortex-A76AE CPU
- cortex-a76: Workaround for erratum 1257314, 1262606, 1262888, 1275112,
1286807
- cortex-a65/a65AE: Support added for Cortex-A65 and Cortex-A65AE CPUs
- cortex-a65: Enable AMU for Cortex-A65
- cortex-a55: Workaround for erratum 1221012
- cortex-a35: Workaround for erratum 855472
- cortex-a9: Workaround for erratum 794073
- Drivers
- console: Allow the console to register multiple times
- delay: Timeout detection support
- gicv3: Enabled multi-socket GIC redistributor frame discovery and migrated
ARM platforms to the new API
- Adds ``gicv3_rdistif_probe`` function that delegates the responsibility
of discovering the corresponding redistributor base frame to each CPU
itself.
- sbsa: Add SBSA watchdog driver
- st/stm32_hash: Add HASH driver
- ti/uart: Add an AArch32 variant
- Library at ROM (romlib)
- Introduce BTI support in Library at ROM (romlib)
- New Platforms Support
- amlogic: g12a: New platform support added for the S905X2 (G12A) platform
- amlogic: meson/gxl: New platform support added for Amlogic Meson
S905x (GXL)
- arm/a5ds: New platform support added for A5 DesignStart
- arm/corstone: New platform support added for Corstone-700
- intel: New platform support added for Agilex
- mediatek: New platform support added for MediaTek mt8183
- qemu/qemu_sbsa: New platform support added for QEMU SBSA platform
- renesas/rcar_gen3: plat: New platform support added for D3
- rockchip: New platform support added for px30
- rockchip: New platform support added for rk3288
- rpi: New platform support added for Raspberry Pi 4
- Platforms
- arm/common: Introduce wrapper functions to setup secure watchdog
- arm/fvp: Add Delay Timer driver to BL1 and BL31 and option for defining
platform DRAM2 base
- arm/fvp: Add Linux DTS files for 32 bit threaded FVPs
- arm/n1sdp: Add code for DDR ECC enablement and BL33 copy to DDR, Initialise CNTFRQ
in Non Secure CNTBaseN
- arm/juno: Use shared mbedtls heap between BL1 and BL2 and add basic support for
dynamic config
- imx: Basic support for PicoPi iMX7D, rdc module init, caam module init,
aipstz init, IMX_SIP_GET_SOC_INFO, IMX_SIP_BUILDINFO added
- intel: Add ncore ccu driver
- mediatek/mt81*: Use new bl31_params_parse() helper
- nvidia: tegra: Add support for multi console interface
- qemu/qemu_sbsa: Adding memory mapping for both FLASH0/FLASH1
- qemu: Added gicv3 support, new console interface in AArch32, and sub-platforms
- renesas/rcar_gen3: plat: Add R-Car V3M support, new board revision for H3ULCB, DBSC4
setting before self-refresh mode
- socionext/uniphier: Support console based on multi-console
- st: stm32mp1: Add OP-TEE, Avenger96, watchdog, LpDDR3, authentication support
and general SYSCFG management
- ti/k3: common: Add support for J721E, Use coherent memory for shared data, Trap all
asynchronous bus errors to EL3
- xilinx/zynqmp: Add support for multi console interface, Initialize IPI table from
zynqmp_config_setup()
- PSCI
- Adding new optional PSCI hook ``pwr_domain_on_finish_late``
- This PSCI hook ``pwr_domain_on_finish_late`` is similar to
``pwr_domain_on_finish`` but is guaranteed to be invoked when the
respective core and cluster are participating in coherency.
- Security
- Speculative Store Bypass Safe (SSBS): Further enhance protection against Spectre
variant 4 by disabling speculative loads/stores (SPSR.SSBS bit) by default.
- UBSAN support and handlers
- Adds support for the Undefined Behaviour sanitizer. There are two types of
support offered - minimalistic trapping support which essentially immediately
crashes on undefined behaviour and full support with full debug messages.
- Tools
- cert_create: Add support for bigger RSA key sizes (3KB and 4KB),
previously the maximum size was 2KB.
- fiptool: Add support to build fiptool on Windows.
Changed
^^^^^^^
- Architecture
- Refactor ARMv8.3 Pointer Authentication support code
- backtrace: Strip PAC field when PAUTH is enabled
- Prettify crash reporting output on AArch64.
- Rework smc_unknown return code path in smc_handler
- Leverage the existing ``el3_exit()`` return routine for smc_unknown return
path rather than a custom set of instructions.
- BL-Specific
- Invalidate dcache build option for BL2 entry at EL3
- Add missing support for BL2_AT_EL3 in XIP memory
- Boot Flow
- Add helper to parse BL31 parameters (both versions)
- Factor out cross-BL API into export headers suitable for 3rd party code
- Introduce lightweight BL platform parameter library
- Drivers
- auth: Memory optimization for Chain of Trust (CoT) description
- bsec: Move bsec_mode_is_closed_device() service to platform
- cryptocell: Move Cryptocell specific API into driver
- gicv3: Prevent pending G1S interrupt from becoming G0 interrupt
- mbedtls: Remove weak heap implementation
- mmc: Increase delay between ACMD41 retries
- mmc: stm32_sdmmc2: Correctly manage block size
- mmc: stm32_sdmmc2: Manage max-frequency property from DT
- synopsys/emmc: Do not change FIFO TH as this breaks some platforms
- synopsys: Update synopsys drivers to not rely on undefined overflow behaviour
- ufs: Extend the delay after reset to wait for some slower chips
- Platforms
- amlogic/meson/gxl: Remove BL2 dependency from BL31
- arm/common: Shorten the Firmware Update (FWU) process
- arm/fvp: Remove GIC initialisation from secondary core cold boot
- arm/sgm: Temporarily disable shared Mbed TLS heap for SGM
- hisilicon: Update hisilicon drivers to not rely on undefined overflow behaviour
- imx: imx8: Replace PLAT_IMX8* with PLAT_imx8*, remove duplicated linker symbols and
deprecated code include, keep only IRQ 32 unmasked, enable all power domain by default
- marvell: Prevent SError accessing PCIe link, Switch to xlat_tables_v2, do not rely on
argument passed via smc, make sure that comphy init will use correct address
- mediatek: mt8173: Refactor RTC and PMIC drivers
- mediatek: mt8173: Apply MULTI_CONSOLE framework
- nvidia: Tegra: memctrl_v2: fix "overflow before widen" coverity issue
- qemu: Simplify the image size calculation, Move and generalise FDT PSCI fixup, move
gicv2 codes to separate file
- renesas/rcar_gen3: Convert to multi-console API, update QoS setting, Update IPL and
Secure Monitor Rev2.0.4, Change to restore timer counter value at resume, Update DDR
setting rev.0.35, qos: change subslot cycle, Change periodic write DQ training option.
- rockchip: Allow SOCs with undefined wfe check bits, Streamline and complete UARTn_BASE
macros, drop rockchip-specific imported linker symbols for bl31, Disable binary generation
for all SOCs, Allow console device to be set by DTB, Use new bl31_params_parse functions
- rpi/rpi3: Move shared rpi3 files into common directory
- socionext/uniphier: Set CONSOLE_FLAG_TRANSLATE_CRLF and clean up console driver
- socionext/uniphier: Replace DIV_ROUND_UP() with div_round_up() from utils_def.h
- st/stm32mp: Split stm32mp_io_setup function, move stm32_get_gpio_bank_clock() to private
file, correctly handle Clock Spreading Generator, move oscillator functions to generic file,
realign device tree files with internal devs, enable RTCAPB clock for dual-core chips, use a
common function to check spinlock is available, move check_header() to common code
- ti/k3: Enable SEPARATE_CODE_AND_RODATA by default, Remove shared RAM space,
Drop _ADDRESS from K3_USART_BASE to match other defines, Remove MSMC port
definitions, Allow USE_COHERENT_MEM for K3, Set L2 latency on A72 cores
- PSCI
- PSCI: Lookup list of parent nodes to lock only once
- Secure Partition Manager (SPM): SPCI Prototype
- Fix service UUID lookup
- Adjust size of virtual address space per partition
- Refactor xlat context creation
- Move shim layer to TTBR1_EL1
- Ignore empty regions in resource description
- Security
- Refactor SPSR initialisation code
- SMMUv3: Abort DMA transactions
- For security DMA should be blocked at the SMMU by default unless explicitly
enabled for a device. SMMU is disabled after reset with all streams bypassing
the SMMU, and abortion of all incoming transactions implements a default deny
policy on reset.
- Moves ``bl1_platform_setup()`` function from arm_bl1_setup.c to FVP platforms'
fvp_bl1_setup.c and fvp_ve_bl1_setup.c files.
- Tools
- cert_create: Remove RSA PKCS#1 v1.5 support
Resolved Issues
^^^^^^^^^^^^^^^
- Architecture
- Fix the CAS spinlock implementation by adding a missing DSB in ``spin_unlock()``
- AArch64: Fix SCTLR bit definitions
- Removes incorrect ``SCTLR_V_BIT`` definition and adds definitions for
ARMv8.3-Pauth `EnIB`, `EnDA` and `EnDB` bits.
- Fix restoration of PAuth context
- Replace call to ``pauth_context_save()`` with ``pauth_context_restore()`` in
case of unknown SMC call.
- BL-Specific Issues
- Fix BL31 crash reporting on AArch64 only platforms
- Build System
- Remove several warnings reported with W=2 and W=1
- Code Quality Issues
- SCTLR and ACTLR are 32-bit for AArch32 and 64-bit for AArch64
- Unify type of "cpu_idx" across PSCI module.
- Assert if power level value greater then PSCI_INVALID_PWR_LVL
- Unsigned long should not be used as per coding guidelines
- Reduce the number of memory leaks in cert_create
- Fix type of cot_desc_ptr
- Use explicit-width data types in AAPCS parameter structs
- Add python configuration for editorconfig
- BL1: Fix type consistency
- Enable -Wshift-overflow=2 to check for undefined shift behavior
- Updated upstream platforms to not rely on undefined overflow behaviour
- Coverity Quality Issues
- Remove GGC ignore -Warray-bounds
- Fix Coverity #261967, Infinite loop
- Fix Coverity #343017, Missing unlock
- Fix Coverity #343008, Side affect in assertion
- Fix Coverity #342970, Uninitialized scalar variable
- CPU Support
- cortex-a12: Fix MIDR mask
- Drivers
- console: Remove Arm console unregister on suspend
- gicv3: Fix support for full SPI range
- scmi: Fix wrong payload length
- Library Code
- libc: Fix sparse warning for __assert()
- libc: Fix memchr implementation
- Platforms
- rpi: rpi3: Fix compilation error when stack protector is enabled
- socionext/uniphier: Fix compilation fail for SPM support build config
- st/stm32mp1: Fix TZC400 configuration against non-secure DDR
- ti/k3: common: Fix RO data area size calculation
- Security
- AArch32: Disable Secure Cycle Counter
- Changes the implementation for disabling Secure Cycle Counter.
For ARMv8.5 the counter gets disabled by setting ``SDCR.SCCD`` bit on
CPU cold/warm boot. For the earlier architectures PMCR register is
saved/restored on secure world entry/exit from/to Non-secure state,
and cycle counting gets disabled by setting PMCR.DP bit.
- AArch64: Disable Secure Cycle Counter
- For ARMv8.5 the counter gets disabled by setting ``MDCR_El3.SCCD`` bit on
CPU cold/warm boot. For the earlier architectures PMCR_EL0 register is
saved/restored on secure world entry/exit from/to Non-secure state,
and cycle counting gets disabled by setting PMCR_EL0.DP bit.
Deprecations
^^^^^^^^^^^^
- Common Code
- Remove MULTI_CONSOLE_API flag and references to it
- Remove deprecated `plat_crash_console_*`
- Remove deprecated interfaces `get_afflvl_shift`, `mpidr_mask_lower_afflvls`, `eret`
- AARCH32/AARCH64 macros are now deprecated in favor of ``__aarch64__``
- ``__ASSEMBLY__`` macro is now deprecated in favor of ``__ASSEMBLER__``
- Drivers
- console: Removed legacy console API
- console: Remove deprecated finish_console_register
- tzc: Remove deprecated types `tzc_action_t` and `tzc_region_attributes_t`
- Secure Partition Manager (SPM):
- Prototype SPCI-based SPM (services/std_svc/spm) will be replaced with alternative
methods of secure partitioning support.
Known Issues
^^^^^^^^^^^^
- Build System Issues
- dtb: DTB creation not supported when building on a Windows host.
This step in the build process is skipped when running on a Windows host. A
known issue from the 1.6 release.
- Platform Issues
- arm/juno: System suspend from Linux does not function as documented in the
user guide
Following the instructions provided in the user guide document does not
result in the platform entering system suspend state as expected. A message
relating to the hdlcd driver failing to suspend will be emitted on the
Linux terminal.
- mediatek/mt6795: This platform does not build in this release
Version 2.1
-----------
New Features
^^^^^^^^^^^^
- Architecture
- Support for ARMv8.3 pointer authentication in the normal and secure worlds
The use of pointer authentication in the normal world is enabled whenever
architectural support is available, without the need for additional build
flags.
Use of pointer authentication in the secure world remains an
experimental configuration at this time. Using both the ``ENABLE_PAUTH``
and ``CTX_INCLUDE_PAUTH_REGS`` build flags, pointer authentication can be
enabled in EL3 and S-EL1/0.
See the :ref:`Firmware Design` document for additional details on the use
of pointer authentication.
- Enable Data Independent Timing (DIT) in EL3, where supported
- Build System
- Support for BL-specific build flags
- Support setting compiler target architecture based on ``ARM_ARCH_MINOR``
build option.
- New ``RECLAIM_INIT_CODE`` build flag:
A significant amount of the code used for the initialization of BL31 is
not needed again after boot time. In order to reduce the runtime memory
footprint, the memory used for this code can be reclaimed after
initialization.
Certain boot-time functions were marked with the ``__init`` attribute to
enable this reclamation.
- CPU Support
- cortex-a76: Workaround for erratum 1073348
- cortex-a76: Workaround for erratum 1220197
- cortex-a76: Workaround for erratum 1130799
- cortex-a75: Workaround for erratum 790748
- cortex-a75: Workaround for erratum 764081
- cortex-a73: Workaround for erratum 852427
- cortex-a73: Workaround for erratum 855423
- cortex-a57: Workaround for erratum 817169
- cortex-a57: Workaround for erratum 814670
- cortex-a55: Workaround for erratum 903758
- cortex-a55: Workaround for erratum 846532
- cortex-a55: Workaround for erratum 798797
- cortex-a55: Workaround for erratum 778703
- cortex-a55: Workaround for erratum 768277
- cortex-a53: Workaround for erratum 819472
- cortex-a53: Workaround for erratum 824069
- cortex-a53: Workaround for erratum 827319
- cortex-a17: Workaround for erratum 852423
- cortex-a17: Workaround for erratum 852421
- cortex-a15: Workaround for erratum 816470
- cortex-a15: Workaround for erratum 827671
- Documentation
- Exception Handling Framework documentation
- Library at ROM (romlib) documentation
- RAS framework documentation
- Coding Guidelines document
- Drivers
- ccn: Add API for setting and reading node registers
- Adds ``ccn_read_node_reg`` function
- Adds ``ccn_write_node_reg`` function
- partition: Support MBR partition entries
- scmi: Add ``plat_css_get_scmi_info`` function
Adds a new API ``plat_css_get_scmi_info`` which lets the platform
register a platform-specific instance of ``scmi_channel_plat_info_t`` and
remove the default values
- tzc380: Add TZC-380 TrustZone Controller driver
- tzc-dmc620: Add driver to manage the TrustZone Controller within the
DMC-620 Dynamic Memory Controller
- Library at ROM (romlib)
- Add platform-specific jump table list
- Allow patching of romlib functions
This change allows patching of functions in the romlib. This can be done by
adding "patch" at the end of the jump table entry for the function that
needs to be patched in the file jmptbl.i.
- Library Code
- Support non-LPAE-enabled MMU tables in AArch32
- mmio: Add ``mmio_clrsetbits_16`` function
- 16-bit variant of ``mmio_clrsetbits``
- object_pool: Add Object Pool Allocator
- Manages object allocation using a fixed-size static array
- Adds ``pool_alloc`` and ``pool_alloc_n`` functions
- Does not provide any functions to free allocated objects (by design)
- libc: Added ``strlcpy`` function
- libc: Import ``strrchr`` function from FreeBSD
- xlat_tables: Add support for ARMv8.4-TTST
- xlat_tables: Support mapping regions without an explicitly specified VA
- Math
- Added softudiv macro to support software division
- Memory Partitioning And Monitoring (MPAM)
- Enabled MPAM EL2 traps (``MPAMHCR_EL2`` and ``MPAM_EL2``)
- Platforms
- amlogic: Add support for Meson S905 (GXBB)
- arm/fvp_ve: Add support for FVP Versatile Express platform
- arm/n1sdp: Add support for Neoverse N1 System Development platform
- arm/rde1edge: Add support for Neoverse E1 platform
- arm/rdn1edge: Add support for Neoverse N1 platform
- arm: Add support for booting directly to Linux without an intermediate
loader (AArch32)
- arm/juno: Enable new CPU errata workarounds for A53 and A57
- arm/juno: Add romlib support
Building a combined BL1 and ROMLIB binary file with the correct page
alignment is now supported on the Juno platform. When ``USE_ROMLIB`` is set
for Juno, it generates the combined file ``bl1_romlib.bin`` which needs to
be used instead of bl1.bin.
- intel/stratix: Add support for Intel Stratix 10 SoC FPGA platform
- marvell: Add support for Armada-37xx SoC platform
- nxp: Add support for i.MX8M and i.MX7 Warp7 platforms
- renesas: Add support for R-Car Gen3 platform
- xilinx: Add support for Versal ACAP platforms
- Position-Independent Executable (PIE)
PIE support has initially been added to BL31. The ``ENABLE_PIE`` build flag is
used to enable or disable this functionality as required.
- Secure Partition Manager
- New SPM implementation based on SPCI Alpha 1 draft specification
A new version of SPM has been implemented, based on the SPCI (Secure
Partition Client Interface) and SPRT (Secure Partition Runtime) draft
specifications.
The new implementation is a prototype that is expected to undergo intensive
rework as the specifications change. It has basic support for multiple
Secure Partitions and Resource Descriptions.
The older version of SPM, based on MM (ARM Management Mode Interface
Specification), is still present in the codebase. A new build flag,
``SPM_MM`` has been added to allow selection of the desired implementation.
This flag defaults to 1, selecting the MM-based implementation.
- Security
- Spectre Variant-1 mitigations (``CVE-2017-5753``)
- Use Speculation Store Bypass Safe (SSBS) functionality where available
Provides mitigation against ``CVE-2018-19440`` (Not saving x0 to x3
registers can leak information from one Normal World SMC client to another)
Changed
^^^^^^^
- Build System
- Warning levels are now selectable with ``W=<1,2,3>``
- Removed unneeded include paths in PLAT_INCLUDES
- "Warnings as errors" (Werror) can be disabled using ``E=0``
- Support totally quiet output with ``-s`` flag
- Support passing options to checkpatch using ``CHECKPATCH_OPTS=<opts>``
- Invoke host compiler with ``HOSTCC / HOSTCCFLAGS`` instead of ``CC / CFLAGS``
- Make device tree pre-processing similar to U-boot/Linux by:
- Creating separate ``CPPFLAGS`` for DT preprocessing so that compiler
options specific to it can be accommodated.
- Replacing ``CPP`` with ``PP`` for DT pre-processing
- CPU Support
- Errata report function definition is now mandatory for CPU support files
CPU operation files must now define a ``<name>_errata_report`` function to
print errata status. This is no longer a weak reference.
- Documentation
- Migrated some content from GitHub wiki to ``docs/`` directory
- Security advisories now have CVE links
- Updated copyright guidelines
- Drivers
- console: The ``MULTI_CONSOLE_API`` framework has been rewritten in C
- console: Ported multi-console driver to AArch32
- gic: Remove 'lowest priority' constants
Removed ``GIC_LOWEST_SEC_PRIORITY`` and ``GIC_LOWEST_NS_PRIORITY``.
Platforms should define these if required, or instead determine the correct
priority values at runtime.
- delay_timer: Check that the Generic Timer extension is present
- mmc: Increase command reply timeout to 10 milliseconds
- mmc: Poll eMMC device status to ensure ``EXT_CSD`` command completion
- mmc: Correctly check return code from ``mmc_fill_device_info``
- External Libraries
- libfdt: Upgraded from 1.4.2 to 1.4.6-9
- mbed TLS: Upgraded from 2.12 to 2.16
This change incorporates fixes for security issues that should be reviewed
to determine if they are relevant for software implementations using
Trusted Firmware-A. See the `mbed TLS releases`_ page for details on
changes from the 2.12 to the 2.16 release.
- Library Code
- compiler-rt: Updated ``lshrdi3.c`` and ``int_lib.h`` with changes from
LLVM master branch (r345645)
- cpu: Updated macro that checks need for ``CVE-2017-5715`` mitigation
- libc: Made setjmp and longjmp C standard compliant
- libc: Allowed overriding the default libc (use ``OVERRIDE_LIBC``)
- libc: Moved setjmp and longjmp to the ``libc/`` directory
- Platforms
- Removed Mbed TLS dependency from plat_bl_common.c
- arm: Removed unused ``ARM_MAP_BL_ROMLIB`` macro
- arm: Removed ``ARM_BOARD_OPTIMISE_MEM`` feature and build flag
- arm: Moved several components into ``drivers/`` directory
This affects the SDS, SCP, SCPI, MHU and SCMI components
- arm/juno: Increased maximum BL2 image size to ``0xF000``
This change was required to accommodate a larger ``libfdt`` library
- SCMI
- Optimized bakery locks when hardware-assisted coherency is enabled using the
``HW_ASSISTED_COHERENCY`` build flag
- SDEI
- Added support for unconditionally resuming secure world execution after
|SDEI| event processing completes
|SDEI| interrupts, although targeting EL3, occur on behalf of the non-secure
world, and may have higher priority than secure world
interrupts. Therefore they might preempt secure execution and yield
execution to the non-secure |SDEI| handler. Upon completion of |SDEI| event
handling, resume secure execution if it was preempted.
- Translation Tables (XLAT)
- Dynamically detect need for ``Common not Private (TTBRn_ELx.CnP)`` bit
Properly handle the case where ``ARMv8.2-TTCNP`` is implemented in a CPU
that does not implement all mandatory v8.2 features (and so must claim to
implement a lower architecture version).
Resolved Issues
^^^^^^^^^^^^^^^
- Architecture
- Incorrect check for SSBS feature detection
- Unintentional register clobber in AArch32 reset_handler function
- Build System
- Dependency issue during DTB image build
- Incorrect variable expansion in Arm platform makefiles
- Building on Windows with verbose mode (``V=1``) enabled is broken
- AArch32 compilation flags is missing ``$(march32-directive)``
- BL-Specific Issues
- bl2: ``uintptr_t is not defined`` error when ``BL2_IN_XIP_MEM`` is defined
- bl2: Missing prototype warning in ``bl2_arch_setup``
- bl31: Omission of Global Offset Table (GOT) section
- Code Quality Issues
- Multiple MISRA compliance issues
- Potential NULL pointer dereference (Coverity-detected)
- Drivers
- mmc: Local declaration of ``scr`` variable causes a cache issue when
invalidating after the read DMA transfer completes
- mmc: ``ACMD41`` does not send voltage information during initialization,
resulting in the command being treated as a query. This prevents the
command from initializing the controller.
- mmc: When checking device state using ``mmc_device_state()`` there are no
retries attempted in the event of an error
- ccn: Incorrect Region ID calculation for RN-I nodes
- console: ``Fix MULTI_CONSOLE_API`` when used as a crash console
- partition: Improper NULL checking in gpt.c
- partition: Compilation failure in ``VERBOSE`` mode (``V=1``)
- Library Code
- common: Incorrect check for Address Authentication support
- xlat: Fix XLAT_V1 / XLAT_V2 incompatibility
The file ``arm_xlat_tables.h`` has been renamed to ``xlat_tables_compat.h``
and has been moved to a common folder. This header can be used to guarantee
compatibility, as it includes the correct header based on
``XLAT_TABLES_LIB_V2``.
- xlat: armclang unused-function warning on ``xlat_clean_dcache_range``
- xlat: Invalid ``mm_cursor`` checks in ``mmap_add`` and ``mmap_add_ctx``
- sdei: Missing ``context.h`` header
- Platforms
- common: Missing prototype warning for ``plat_log_get_prefix``
- arm: Insufficient maximum BL33 image size
- arm: Potential memory corruption during BL2-BL31 transition
On Arm platforms, the BL2 memory can be overlaid by BL31/BL32. The memory
descriptors describing the list of executable images are created in BL2
R/W memory, which could be possibly corrupted later on by BL31/BL32 due
to overlay. This patch creates a reserved location in SRAM for these
descriptors and are copied over by BL2 before handing over to next BL
image.
- juno: Invalid behaviour when ``CSS_USE_SCMI_SDS_DRIVER`` is not set
In ``juno_pm.c`` the ``css_scmi_override_pm_ops`` function was used
regardless of whether the build flag was set. The original behaviour has
been restored in the case where the build flag is not set.
- Tools
- fiptool: Incorrect UUID parsing of blob parameters
- doimage: Incorrect object rules in Makefile
Deprecations
^^^^^^^^^^^^
- Common Code
- ``plat_crash_console_init`` function
- ``plat_crash_console_putc`` function
- ``plat_crash_console_flush`` function
- ``finish_console_register`` macro
- AArch64-specific Code
- helpers: ``get_afflvl_shift``
- helpers: ``mpidr_mask_lower_afflvls``
- helpers: ``eret``
- Secure Partition Manager (SPM)
- Boot-info structure
Known Issues
^^^^^^^^^^^^
- Build System Issues
- dtb: DTB creation not supported when building on a Windows host.
This step in the build process is skipped when running on a Windows host. A
known issue from the 1.6 release.
- Platform Issues
- arm/juno: System suspend from Linux does not function as documented in the
user guide
Following the instructions provided in the user guide document does not
result in the platform entering system suspend state as expected. A message
relating to the hdlcd driver failing to suspend will be emitted on the
Linux terminal.
- arm/juno: The firmware update use-cases do not work with motherboard
firmware version < v1.5.0 (the reset reason is not preserved). The Linaro
18.04 release has MB v1.4.9. The MB v1.5.0 is available in Linaro 18.10
release.
- mediatek/mt6795: This platform does not build in this release
Version 2.0
-----------
New Features
^^^^^^^^^^^^
- Removal of a number of deprecated APIs
- A new Platform Compatibility Policy document has been created which
references a wiki page that maintains a listing of deprecated
interfaces and the release after which they will be removed.
- All deprecated interfaces except the MULTI_CONSOLE_API have been removed
from the code base.
- Various Arm and partner platforms have been updated to remove the use of
removed APIs in this release.
- This release is otherwise unchanged from 1.6 release
Issues resolved since last release
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
- No issues known at 1.6 release resolved in 2.0 release
Known Issues
^^^^^^^^^^^^
- DTB creation not supported when building on a Windows host. This step in the
build process is skipped when running on a Windows host. Known issue from
1.6 version.
- As a result of removal of deprecated interfaces the Nvidia Tegra, Marvell
Armada 8K and MediaTek MT6795 platforms do not build in this release.
Also MediaTek MT8173, NXP QorIQ LS1043A, NXP i.MX8QX, NXP i.MX8QMa,
Rockchip RK3328, Rockchip RK3368 and Rockchip RK3399 platforms have not been
confirmed to be working after the removal of the deprecated interfaces
although they do build.
Version 1.6
-----------
New Features
^^^^^^^^^^^^
- Addressing Speculation Security Vulnerabilities
- Implement static workaround for CVE-2018-3639 for AArch32 and AArch64
- Add support for dynamic mitigation for CVE-2018-3639
- Implement dynamic mitigation for CVE-2018-3639 on Cortex-A76
- Ensure |SDEI| handler executes with CVE-2018-3639 mitigation enabled
- Introduce RAS handling on AArch64
- Some RAS extensions are mandatory for Armv8.2 CPUs, with others
mandatory for Armv8.4 CPUs however, all extensions are also optional
extensions to the base Armv8.0 architecture.
- The Armv8 RAS Extensions introduced Standard Error Records which are a
set of standard registers to configure RAS node policy and allow RAS
Nodes to record and expose error information for error handling agents.
- Capabilities are provided to support RAS Node enumeration and iteration
along with individual interrupt registrations and fault injections
support.
- Introduce handlers for Uncontainable errors, Double Faults and EL3
External Aborts
- Enable Memory Partitioning And Monitoring (MPAM) for lower EL's
- Memory Partitioning And Monitoring is an Armv8.4 feature that enables
various memory system components and resources to define partitions.
Software running at various ELs can then assign themselves to the
desired partition to control their performance aspects.
- When ENABLE_MPAM_FOR_LOWER_ELS is set to 1, EL3 allows
lower ELs to access their own MPAM registers without trapping to EL3.
This patch however, doesn't make use of partitioning in EL3; platform
initialisation code should configure and use partitions in EL3 if
required.
- Introduce ROM Lib Feature
- Support combining several libraries into a self-called "romlib" image,
that may be shared across images to reduce memory footprint. The romlib
image is stored in ROM but is accessed through a jump-table that may be
stored in read-write memory, allowing for the library code to be patched.
- Introduce Backtrace Feature
- This function displays the backtrace, the current EL and security state
to allow a post-processing tool to choose the right binary to interpret
the dump.
- Print backtrace in assert() and panic() to the console.
- Code hygiene changes and alignment with MISRA C-2012 guideline with fixes
addressing issues complying to the following rules:
- MISRA rules 4.9, 5.1, 5.3, 5.7, 8.2-8.5, 8.8, 8.13, 9.3, 10.1,
10.3-10.4, 10.8, 11.3, 11.6, 12.1, 14.4, 15.7, 16.1-16.7, 17.7-17.8,
20.7, 20.10, 20.12, 21.1, 21.15, 22.7
- Clean up the usage of void pointers to access symbols
- Increase usage of static qualifier to locally used functions and data
- Migrated to use of u_register_t for register read/write to better
match AArch32 and AArch64 type sizes
- Use int-ll64 for both AArch32 and AArch64 to assist in consistent
format strings between architectures
- Clean up TF-A libc by removing non arm copyrighted implementations
and replacing them with modified FreeBSD and SCC implementations
- Various changes to support Clang linker and assembler
- The clang assembler/preprocessor is used when Clang is selected. However,
the clang linker is not used because it is unable to link TF-A objects
due to immaturity of clang linker functionality at this time.
- Refactor support APIs into Libraries
- Evolve libfdt, mbed TLS library and standard C library sources as
proper libraries that TF-A may be linked against.
- CPU Enhancements
- Add CPU support for Cortex-Ares and Cortex-A76
- Add AMU support for Cortex-Ares
- Add initial CPU support for Cortex-Deimos
- Add initial CPU support for Cortex-Helios
- Implement dynamic mitigation for CVE-2018-3639 on Cortex-A76
- Implement Cortex-Ares erratum 1043202 workaround
- Implement DSU erratum 936184 workaround
- Check presence of fix for errata 843419 in Cortex-A53
- Check presence of fix for errata 835769 in Cortex-A53
- Translation Tables Enhancements
- The xlat v2 library has been refactored in order to be reused by
different TF components at different EL's including the addition of EL2.
Some refactoring to make the code more generic and less specific to TF,
in order to reuse the library outside of this project.
- SPM Enhancements
- General cleanups and refactoring to pave the way to multiple partitions
support
- SDEI Enhancements
- Allow platforms to define explicit events
- Determine client EL from NS context's SCR_EL3
- Make dispatches synchronous
- Introduce jump primitives for BL31
- Mask events after CPU wakeup in |SDEI| dispatcher to conform to the
specification
- Misc TF-A Core Common Code Enhancements
- Add support for eXecute In Place (XIP) memory in BL2
- Add support for the SMC Calling Convention 2.0
- Introduce External Abort handling on AArch64
External Abort routed to EL3 was reported as an unhandled exception
and caused a panic. This change enables Trusted Firmware-A to handle
External Aborts routed to EL3.
- Save value of ACTLR_EL1 implementation-defined register in the CPU
context structure rather than forcing it to 0.
- Introduce ARM_LINUX_KERNEL_AS_BL33 build option, which allows BL31 to
directly jump to a Linux kernel. This makes for a quicker and simpler
boot flow, which might be useful in some test environments.
- Add dynamic configurations for BL31, BL32 and BL33 enabling support for
Chain of Trust (COT).
- Make TF UUID RFC 4122 compliant
- New Platform Support
- Arm SGI-575
- Arm SGM-775
- Allwinner sun50i_64
- Allwinner sun50i_h6
- NXP QorIQ LS1043A
- NXP i.MX8QX
- NXP i.MX8QM
- NXP i.MX7Solo WaRP7
- TI K3
- Socionext Synquacer SC2A11
- Marvell Armada 8K
- STMicroelectronics STM32MP1
- Misc Generic Platform Common Code Enhancements
- Add MMC framework that supports both eMMC and SD card devices
- Misc Arm Platform Common Code Enhancements
- Demonstrate PSCI MEM_PROTECT from el3_runtime
- Provide RAS support
- Migrate AArch64 port to the multi console driver. The old API is
deprecated and will eventually be removed.
- Move BL31 below BL2 to enable BL2 overlay resulting in changes in the
layout of BL images in memory to enable more efficient use of available
space.
- Add cpp build processing for dtb that allows processing device tree
with external includes.
- Extend FIP io driver to support multiple FIP devices
- Add support for SCMI AP core configuration protocol v1.0
- Use SCMI AP core protocol to set the warm boot entrypoint
- Add support to Mbed TLS drivers for shared heap among different
BL images to help optimise memory usage
- Enable non-secure access to UART1 through a build option to support
a serial debug port for debugger connection
- Enhancements for Arm Juno Platform
- Add support for TrustZone Media Protection 1 (TZMP1)
- Enhancements for Arm FVP Platform
- Dynamic_config: remove the FVP dtb files
- Set DYNAMIC_WORKAROUND_CVE_2018_3639=1 on FVP by default
- Set the ability to dynamically disable Trusted Boot Board
authentication to be off by default with DYN_DISABLE_AUTH
- Add librom enhancement support in FVP
- Support shared Mbed TLS heap between BL1 and BL2 that allow a
reduction in BL2 size for FVP
- Enhancements for Arm SGI/SGM Platform
- Enable ARM_PLAT_MT flag for SGI-575
- Add dts files to enable support for dynamic config
- Add RAS support
- Support shared Mbed TLS heap for SGI and SGM between BL1 and BL2
- Enhancements for Non Arm Platforms
- Raspberry Pi Platform
- Hikey Platforms
- Xilinx Platforms
- QEMU Platform
- Rockchip rk3399 Platform
- TI Platforms
- Socionext Platforms
- Allwinner Platforms
- NXP Platforms
- NVIDIA Tegra Platform
- Marvell Platforms
- STMicroelectronics STM32MP1 Platform
Issues resolved since last release
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
- No issues known at 1.5 release resolved in 1.6 release
Known Issues
^^^^^^^^^^^^
- DTB creation not supported when building on a Windows host. This step in the
build process is skipped when running on a Windows host. Known issue from
1.5 version.
Version 1.5
-----------
New features
^^^^^^^^^^^^
- Added new firmware support to enable RAS (Reliability, Availability, and
Serviceability) functionality.
- Secure Partition Manager (SPM): A Secure Partition is a software execution
environment instantiated in S-EL0 that can be used to implement simple
management and security services. The SPM is the firmware component that
is responsible for managing a Secure Partition.
- SDEI dispatcher: Support for interrupt-based |SDEI| events and all
interfaces as defined by the |SDEI| specification v1.0, see
`SDEI Specification`_
- Exception Handling Framework (EHF): Framework that allows dispatching of
EL3 interrupts to their registered handlers which are registered based on
their priorities. Facilitates firmware-first error handling policy where
asynchronous exceptions may be routed to EL3.
Integrated the TSPD with EHF.
- Updated PSCI support:
- Implemented PSCI v1.1 optional features `MEM_PROTECT` and `SYSTEM_RESET2`.
The supported PSCI version was updated to v1.1.
- Improved PSCI STAT timestamp collection, including moving accounting for
retention states to be inside the locks and fixing handling of wrap-around
when calculating residency in AArch32 execution state.
- Added optional handler for early suspend that executes when suspending to
a power-down state and with data caches enabled.
This may provide a performance improvement on platforms where it is safe
to perform some or all of the platform actions from `pwr_domain_suspend`
with the data caches enabled.
- Enabled build option, BL2_AT_EL3, for BL2 to allow execution at EL3 without
any dependency on TF BL1.
This allows platforms which already have a non-TF Boot ROM to directly load
and execute BL2 and subsequent BL stages without need for BL1. This was not
previously possible because BL2 executes at S-EL1 and cannot jump straight to
EL3.
- Implemented support for SMCCC v1.1, including `SMCCC_VERSION` and
`SMCCC_ARCH_FEATURES`.
Additionally, added support for `SMCCC_VERSION` in PSCI features to enable
discovery of the SMCCC version via PSCI feature call.
- Added Dynamic Configuration framework which enables each of the boot loader
stages to be dynamically configured at runtime if required by the platform.
The boot loader stage may optionally specify a firmware configuration file
and/or hardware configuration file that can then be shared with the next boot
loader stage.
Introduced a new BL handover interface that essentially allows passing of 4
arguments between the different BL stages.
Updated cert_create and fip_tool to support the dynamic configuration files.
The COT also updated to support these new files.
- Code hygiene changes and alignment with MISRA guideline:
- Fix use of undefined macros.
- Achieved compliance with Mandatory MISRA coding rules.
- Achieved compliance for following Required MISRA rules for the default
build configurations on FVP and Juno platforms : 7.3, 8.3, 8.4, 8.5 and
8.8.
- Added support for Armv8.2-A architectural features:
- Updated translation table set-up to set the CnP (Common not Private) bit
for secure page tables so that multiple PEs in the same Inner Shareable
domain can use the same translation table entries for a given stage of
translation in a particular translation regime.
- Extended the supported values of ID_AA64MMFR0_EL1.PARange to include the
52-bit Physical Address range.
- Added support for the Scalable Vector Extension to allow Normal world
software to access SVE functionality but disable access to SVE, SIMD and
floating point functionality from the Secure world in order to prevent
corruption of the Z-registers.
- Added support for Armv8.4-A architectural feature Activity Monitor Unit (AMU)
extensions.
In addition to the v8.4 architectural extension, AMU support on Cortex-A75
was implemented.
- Enhanced OP-TEE support to enable use of pageable OP-TEE image. The Arm
standard platforms are updated to load up to 3 images for OP-TEE; header,
pager image and paged image.
The chain of trust is extended to support the additional images.
- Enhancements to the translation table library:
- Introduced APIs to get and set the memory attributes of a region.
- Added support to manage both privilege levels in translation regimes that
describe translations for 2 Exception levels, specifically the EL1&0
translation regime, and extended the memory map region attributes to
include specifying Non-privileged access.
- Added support to specify the granularity of the mappings of each region,
for instance a 2MB region can be specified to be mapped with 4KB page
tables instead of a 2MB block.
- Disabled the higher VA range to avoid unpredictable behaviour if there is
an attempt to access addresses in the higher VA range.
- Added helpers for Device and Normal memory MAIR encodings that align with
the Arm Architecture Reference Manual for Armv8-A (Arm DDI0487B.b).
- Code hygiene including fixing type length and signedness of constants,
refactoring of function to enable the MMU, removing all instances where
the virtual address space is hardcoded and added comments that document
alignment needed between memory attributes and attributes specified in
TCR_ELx.
- Updated GIC support:
- Introduce new APIs for GICv2 and GICv3 that provide the capability to
specify interrupt properties rather than list of interrupt numbers alone.
The Arm platforms and other upstream platforms are migrated to use
interrupt properties.
- Added helpers to save / restore the GICv3 context, specifically the
Distributor and Redistributor contexts and architectural parts of the ITS
power management. The Distributor and Redistributor helpers also support
the implementation-defined part of GIC-500 and GIC-600.
Updated the Arm FVP platform to save / restore the GICv3 context on system
suspend / resume as an example of how to use the helpers.
Introduced a new TZC secured DDR carve-out for use by Arm platforms for
storing EL3 runtime data such as the GICv3 register context.
- Added support for Armv7-A architecture via build option ARM_ARCH_MAJOR=7.
This includes following features:
- Updates GICv2 driver to manage GICv1 with security extensions.
- Software implementation for 32bit division.
- Enabled use of generic timer for platforms that do not set
ARM_CORTEX_Ax=yes.
- Support for Armv7-A Virtualization extensions [DDI0406C_C].
- Support for both Armv7-A platforms that only have 32-bit addressing and
Armv7-A platforms that support large page addressing.
- Included support for following Armv7 CPUs: Cortex-A12, Cortex-A17,
Cortex-A7, Cortex-A5, Cortex-A9, Cortex-A15.
- Added support in QEMU for Armv7-A/Cortex-A15.
- Enhancements to Firmware Update feature:
- Updated the FWU documentation to describe the additional images needed for
Firmware update, and how they are used for both the Juno platform and the
Arm FVP platforms.
- Enhancements to Trusted Board Boot feature:
- Added support to cert_create tool for RSA PKCS1# v1.5 and SHA384, SHA512
and SHA256.
- For Arm platforms added support to use ECDSA keys.
- Enhanced the mbed TLS wrapper layer to include support for both RSA and
ECDSA to enable runtime selection between RSA and ECDSA keys.
- Added support for secure interrupt handling in AArch32 sp_min, hardcoded to
only handle FIQs.
- Added support to allow a platform to load images from multiple boot sources,
for example from a second flash drive.
- Added a logging framework that allows platforms to reduce the logging level
at runtime and additionally the prefix string can be defined by the platform.
- Further improvements to register initialisation:
- Control register PMCR_EL0 / PMCR is set to prohibit cycle counting in the
secure world. This register is added to the list of registers that are
saved and restored during world switch.
- When EL3 is running in AArch32 execution state, the Non-secure version of
SCTLR is explicitly initialised during the warmboot flow rather than
relying on the hardware to set the correct reset values.
- Enhanced support for Arm platforms:
- Introduced driver for Shared-Data-Structure (SDS) framework which is used
for communication between SCP and the AP CPU, replacing Boot-Over_MHU
(BOM) protocol.
The Juno platform is migrated to use SDS with the SCMI support added in
v1.3 and is set as default.
The driver can be found in the plat/arm/css/drivers folder.
- Improved memory usage by only mapping TSP memory region when the TSPD has
been included in the build. This reduces the memory footprint and avoids
unnecessary memory being mapped.
- Updated support for multi-threading CPUs for FVP platforms - always check
the MT field in MPDIR and access the bit fields accordingly.
- Support building for platforms that model DynamIQ configuration by
implementing all CPUs in a single cluster.
- Improved nor flash driver, for instance clearing status registers before
sending commands. Driver can be found plat/arm/board/common folder.
- Enhancements to QEMU platform:
- Added support for TBB.
- Added support for using OP-TEE pageable image.
- Added support for LOAD_IMAGE_V2.
- Migrated to use translation table library v2 by default.
- Added support for SEPARATE_CODE_AND_RODATA.
- Applied workarounds CVE-2017-5715 on Arm Cortex-A57, -A72, -A73 and -A75, and
for Armv7-A CPUs Cortex-A9, -A15 and -A17.
- Applied errata workaround for Arm Cortex-A57: 859972.
- Applied errata workaround for Arm Cortex-A72: 859971.
- Added support for Poplar 96Board platform.
- Added support for Raspberry Pi 3 platform.
- Added Call Frame Information (CFI) assembler directives to the vector entries
which enables debuggers to display the backtrace of functions that triggered
a synchronous abort.
- Added ability to build dtb.
- Added support for pre-tool (cert_create and fiptool) image processing
enabling compression of the image files before processing by cert_create and
fiptool.
This can reduce fip size and may also speed up loading of images. The image
verification will also get faster because certificates are generated based on
compressed images.
Imported zlib 1.2.11 to implement gunzip() for data compression.
- Enhancements to fiptool:
- Enabled the fiptool to be built using Visual Studio.
- Added padding bytes at the end of the last image in the fip to be
facilitate transfer by DMA.
Issues resolved since last release
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
- TF-A can be built with optimisations disabled (-O0).
- Memory layout updated to enable Trusted Board Boot on Juno platform when
running TF-A in AArch32 execution mode (resolving `tf-issue#501`_).
Known Issues
^^^^^^^^^^^^
- DTB creation not supported when building on a Windows host. This step in the
build process is skipped when running on a Windows host.
Version 1.4
-----------
New features
^^^^^^^^^^^^
- Enabled support for platforms with hardware assisted coherency.
A new build option HW_ASSISTED_COHERENCY allows platforms to take advantage
of the following optimisations:
- Skip performing cache maintenance during power-up and power-down.
- Use spin-locks instead of bakery locks.
- Enable data caches early on warm-booted CPUs.
- Added support for Cortex-A75 and Cortex-A55 processors.
Both Cortex-A75 and Cortex-A55 processors use the Arm DynamIQ Shared Unit
(DSU). The power-down and power-up sequences are therefore mostly managed in
hardware, reducing complexity of the software operations.
- Introduced Arm GIC-600 driver.
Arm GIC-600 IP complies with Arm GICv3 architecture. For FVP platforms, the
GIC-600 driver is chosen when FVP_USE_GIC_DRIVER is set to FVP_GIC600.
- Updated GICv3 support:
- Introduced power management APIs for GICv3 Redistributor. These APIs
allow platforms to power down the Redistributor during CPU power on/off.
Requires the GICv3 implementations to have power management operations.
Implemented the power management APIs for FVP.
- GIC driver data is flushed by the primary CPU so that secondary CPU do
not read stale GIC data.
- Added support for Arm System Control and Management Interface v1.0 (SCMI).
The SCMI driver implements the power domain management and system power
management protocol of the SCMI specification (Arm DEN 0056ASCMI) for
communicating with any compliant power controller.
Support is added for the Juno platform. The driver can be found in the
plat/arm/css/drivers folder.
- Added support to enable pre-integration of TBB with the Arm TrustZone
CryptoCell product, to take advantage of its hardware Root of Trust and
crypto acceleration services.
- Enabled Statistical Profiling Extensions for lower ELs.
The firmware support is limited to the use of SPE in the Non-secure state
and accesses to the SPE specific registers from S-EL1 will trap to EL3.
The SPE are architecturally specified for AArch64 only.
- Code hygiene changes aligned with MISRA guidelines:
- Fixed signed / unsigned comparison warnings in the translation table
library.
- Added U(_x) macro and together with the existing ULL(_x) macro fixed
some of the signed-ness defects flagged by the MISRA scanner.
- Enhancements to Firmware Update feature:
- The FWU logic now checks for overlapping images to prevent execution of
unauthenticated arbitrary code.
- Introduced new FWU_SMC_IMAGE_RESET SMC that changes the image loading
state machine to go from COPYING, COPIED or AUTHENTICATED states to
RESET state. Previously, this was only possible when the authentication
of an image failed or when the execution of the image finished.
- Fixed integer overflow which addressed TFV-1: Malformed Firmware Update
SMC can result in copy of unexpectedly large data into secure memory.
- Introduced support for Arm Compiler 6 and LLVM (clang).
TF-A can now also be built with the Arm Compiler 6 or the clang compilers.
The assembler and linker must be provided by the GNU toolchain.
Tested with Arm CC 6.7 and clang 3.9.x and 4.0.x.
- Memory footprint improvements:
- Introduced `tf_snprintf`, a reduced version of `snprintf` which has
support for a limited set of formats.
The mbedtls driver is updated to optionally use `tf_snprintf` instead of
`snprintf`.
- The `assert()` is updated to no longer print the function name, and
additional logging options are supported via an optional platform define
`PLAT_LOG_LEVEL_ASSERT`, which controls how verbose the assert output is.
- Enhancements to TF-A support when running in AArch32 execution state:
- Support booting SP_MIN and BL33 in AArch32 execution mode on Juno. Due to
hardware limitations, BL1 and BL2 boot in AArch64 state and there is
additional trampoline code to warm reset into SP_MIN in AArch32 execution
state.
- Added support for Arm Cortex-A53/57/72 MPCore processors including the
errata workarounds that are already implemented for AArch64 execution
state.
- For FVP platforms, added AArch32 Trusted Board Boot support, including the
Firmware Update feature.
- Introduced Arm SiP service for use by Arm standard platforms.
- Added new Arm SiP Service SMCs to enable the Non-secure world to read PMF
timestamps.
Added PMF instrumentation points in TF-A in order to quantify the
overall time spent in the PSCI software implementation.
- Added new Arm SiP service SMC to switch execution state.
This allows the lower exception level to change its execution state from
AArch64 to AArch32, or vice verse, via a request to EL3.
- Migrated to use SPDX[0] license identifiers to make software license
auditing simpler.
.. note::
Files that have been imported by FreeBSD have not been modified.
[0]: https://spdx.org/
- Enhancements to the translation table library:
- Added version 2 of translation table library that allows different
translation tables to be modified by using different 'contexts'. Version 1
of the translation table library only allows the current EL's translation
tables to be modified.
Version 2 of the translation table also added support for dynamic
regions; regions that can be added and removed dynamically whilst the
MMU is enabled. Static regions can only be added or removed before the
MMU is enabled.
The dynamic mapping functionality is enabled or disabled when compiling
by setting the build option PLAT_XLAT_TABLES_DYNAMIC to 1 or 0. This can
be done per-image.
- Added support for translation regimes with two virtual address spaces
such as the one shared by EL1 and EL0.
The library does not support initializing translation tables for EL0
software.
- Added support to mark the translation tables as non-cacheable using an
additional build option `XLAT_TABLE_NC`.
- Added support for GCC stack protection. A new build option
ENABLE_STACK_PROTECTOR was introduced that enables compilation of all BL
images with one of the GCC -fstack-protector-* options.
A new platform function plat_get_stack_protector_canary() was introduced
that returns a value used to initialize the canary for stack corruption
detection. For increased effectiveness of protection platforms must provide
an implementation that returns a random value.
- Enhanced support for Arm platforms:
- Added support for multi-threading CPUs, indicated by `MT` field in MPDIR.
A new build flag `ARM_PLAT_MT` is added, and when enabled, the functions
accessing MPIDR assume that the `MT` bit is set for the platform and
access the bit fields accordingly.
Also, a new API `plat_arm_get_cpu_pe_count` is added when `ARM_PLAT_MT` is
enabled, returning the Processing Element count within the physical CPU
corresponding to `mpidr`.
- The Arm platforms migrated to use version 2 of the translation tables.
- Introduced a new Arm platform layer API `plat_arm_psci_override_pm_ops`
which allows Arm platforms to modify `plat_arm_psci_pm_ops` and therefore
dynamically define PSCI capability.
- The Arm platforms migrated to use IMAGE_LOAD_V2 by default.
- Enhanced reporting of errata workaround status with the following policy:
- If an errata workaround is enabled:
- If it applies (i.e. the CPU is affected by the errata), an INFO message
is printed, confirming that the errata workaround has been applied.
- If it does not apply, a VERBOSE message is printed, confirming that the
errata workaround has been skipped.
- If an errata workaround is not enabled, but would have applied had it
been, a WARN message is printed, alerting that errata workaround is
missing.
- Added build options ARM_ARCH_MAJOR and ARM_ARM_MINOR to choose the
architecture version to target TF-A.
- Updated the spin lock implementation to use the more efficient CAS (Compare
And Swap) instruction when available. This instruction was introduced in
Armv8.1-A.
- Applied errata workaround for Arm Cortex-A53: 855873.
- Applied errata workaround for Arm-Cortex-A57: 813419.
- Enabled all A53 and A57 errata workarounds for Juno, both in AArch64 and
AArch32 execution states.
- Added support for Socionext UniPhier SoC platform.
- Added support for Hikey960 and Hikey platforms.
- Added support for Rockchip RK3328 platform.
- Added support for NVidia Tegra T186 platform.
- Added support for Designware emmc driver.
- Imported libfdt v1.4.2 that addresses buffer overflow in fdt_offset_ptr().
- Enhanced the CPU operations framework to allow power handlers to be
registered on per-level basis. This enables support for future CPUs that
have multiple threads which might need powering down individually.
- Updated register initialisation to prevent unexpected behaviour:
- Debug registers MDCR-EL3/SDCR and MDCR_EL2/HDCR are initialised to avoid
unexpected traps into the higher exception levels and disable secure
self-hosted debug. Additionally, secure privileged external debug on
Juno is disabled by programming the appropriate Juno SoC registers.
- EL2 and EL3 configurable controls are initialised to avoid unexpected
traps in the higher exception levels.
- Essential control registers are fully initialised on EL3 start-up, when
initialising the non-secure and secure context structures and when
preparing to leave EL3 for a lower EL. This gives better alignment with
the Arm ARM which states that software must initialise RES0 and RES1
fields with 0 / 1.
- Enhanced PSCI support:
- Introduced new platform interfaces that decouple PSCI stat residency
calculation from PMF, enabling platforms to use alternative methods of
capturing timestamps.
- PSCI stat accounting performed for retention/standby states when
requested at multiple power levels.
- Simplified fiptool to have a single linked list of image descriptors.
- For the TSP, resolved corruption of pre-empted secure context by aborting any
pre-empted SMC during PSCI power management requests.
Issues resolved since last release
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
- TF-A can be built with the latest mbed TLS version (v2.4.2). The earlier
version 2.3.0 cannot be used due to build warnings that the TF-A build
system interprets as errors.
- TBBR, including the Firmware Update feature is now supported on FVP
platforms when running TF-A in AArch32 state.
- The version of the AEMv8 Base FVP used in this release has resolved the issue
of the model executing a reset instead of terminating in response to a
shutdown request using the PSCI SYSTEM_OFF API.
Known Issues
^^^^^^^^^^^^
- Building TF-A with compiler optimisations disabled (-O0) fails.
- Trusted Board Boot currently does not work on Juno when running Trusted
Firmware in AArch32 execution state due to error when loading the sp_min to
memory because of lack of free space available. See `tf-issue#501`_ for more
details.
- The errata workaround for A53 errata 843419 is only available from binutils
2.26 and is not present in GCC4.9. If this errata is applicable to the
platform, please use GCC compiler version of at least 5.0. See `PR#1002`_ for
more details.
Version 1.3
-----------
New features
^^^^^^^^^^^^
- Added support for running TF-A in AArch32 execution state.
The PSCI library has been refactored to allow integration with **EL3 Runtime
Software**. This is software that is executing at the highest secure
privilege which is EL3 in AArch64 or Secure SVC/Monitor mode in AArch32. See
:ref:`PSCI Library Integration guide for Armv8-A AArch32 systems`.
Included is a minimal AArch32 Secure Payload, **SP-MIN**, that illustrates
the usage and integration of the PSCI library with EL3 Runtime Software
running in AArch32 state.
Booting to the BL1/BL2 images as well as booting straight to the Secure
Payload is supported.
- Improvements to the initialization framework for the PSCI service and Arm
Standard Services in general.
The PSCI service is now initialized as part of Arm Standard Service
initialization. This consolidates the initializations of any Arm Standard
Service that may be added in the future.
A new function ``get_arm_std_svc_args()`` is introduced to get arguments
corresponding to each standard service and must be implemented by the EL3
Runtime Software.
For PSCI, a new versioned structure ``psci_lib_args_t`` is introduced to
initialize the PSCI Library. **Note** this is a compatibility break due to
the change in the prototype of ``psci_setup()``.
- To support AArch32 builds of BL1 and BL2, implemented a new, alternative
firmware image loading mechanism that adds flexibility.
The current mechanism has a hard-coded set of images and execution order
(BL31, BL32, etc). The new mechanism is data-driven by a list of image
descriptors provided by the platform code.
Arm platforms have been updated to support the new loading mechanism.
The new mechanism is enabled by a build flag (``LOAD_IMAGE_V2``) which is
currently off by default for the AArch64 build.
**Note** ``TRUSTED_BOARD_BOOT`` is currently not supported when
``LOAD_IMAGE_V2`` is enabled.
- Updated requirements for making contributions to TF-A.
Commits now must have a 'Signed-off-by:' field to certify that the
contribution has been made under the terms of the
:download:`Developer Certificate of Origin <../dco.txt>`.
A signed CLA is no longer required.
The :ref:`Contributor's Guide` has been updated to reflect this change.
- Introduced Performance Measurement Framework (PMF) which provides support
for capturing, storing, dumping and retrieving time-stamps to measure the
execution time of critical paths in the firmware. This relies on defining
fixed sample points at key places in the code.
- To support the QEMU platform port, imported libfdt v1.4.1 from
https://git.kernel.org/pub/scm/utils/dtc/dtc.git
- Updated PSCI support:
- Added support for PSCI NODE_HW_STATE API for Arm platforms.
- New optional platform hook, ``pwr_domain_pwr_down_wfi()``, in
``plat_psci_ops`` to enable platforms to perform platform-specific actions
needed to enter powerdown, including the 'wfi' invocation.
- PSCI STAT residency and count functions have been added on Arm platforms
by using PMF.
- Enhancements to the translation table library:
- Limited memory mapping support for region overlaps to only allow regions
to overlap that are identity mapped or have the same virtual to physical
address offset, and overlap completely but must not cover the same area.
This limitation will enable future enhancements without having to
support complex edge cases that may not be necessary.
- The initial translation lookup level is now inferred from the virtual
address space size. Previously, it was hard-coded.
- Added support for mapping Normal, Inner Non-cacheable, Outer
Non-cacheable memory in the translation table library.
This can be useful to map a non-cacheable memory region, such as a DMA
buffer.
- Introduced the MT_EXECUTE/MT_EXECUTE_NEVER memory mapping attributes to
specify the access permissions for instruction execution of a memory
region.
- Enabled support to isolate code and read-only data on separate memory pages,
allowing independent access control to be applied to each.
- Enabled SCR_EL3.SIF (Secure Instruction Fetch) bit in BL1 and BL31 common
architectural setup code, preventing fetching instructions from non-secure
memory when in secure state.
- Enhancements to FIP support:
- Replaced ``fip_create`` with ``fiptool`` which provides a more consistent
and intuitive interface as well as additional support to remove an image
from a FIP file.
- Enabled printing the SHA256 digest with info command, allowing quick
verification of an image within a FIP without having to extract the
image and running sha256sum on it.
- Added support for unpacking the contents of an existing FIP file into
the working directory.
- Aligned command line options for specifying images to use same naming
convention as specified by TBBR and already used in cert_create tool.
- Refactored the TZC-400 driver to also support memory controllers that
integrate TZC functionality, for example Arm CoreLink DMC-500. Also added
DMC-500 specific support.
- Implemented generic delay timer based on the system generic counter and
migrated all platforms to use it.
- Enhanced support for Arm platforms:
- Updated image loading support to make SCP images (SCP_BL2 and SCP_BL2U)
optional.
- Enhanced topology description support to allow multi-cluster topology
definitions.
- Added interconnect abstraction layer to help platform ports select the
right interconnect driver, CCI or CCN, for the platform.
- Added support to allow loading BL31 in the TZC-secured DRAM instead of
the default secure SRAM.
- Added support to use a System Security Control (SSC) Registers Unit
enabling TF-A to be compiled to support multiple Arm platforms and
then select one at runtime.
- Restricted mapping of Trusted ROM in BL1 to what is actually needed by
BL1 rather than entire Trusted ROM region.
- Flash is now mapped as execute-never by default. This increases security
by restricting the executable region to what is strictly needed.
- Applied following erratum workarounds for Cortex-A57: 833471, 826977,
829520, 828024 and 826974.
- Added support for Mediatek MT6795 platform.
- Added support for QEMU virtualization Armv8-A target.
- Added support for Rockchip RK3368 and RK3399 platforms.
- Added support for Xilinx Zynq UltraScale+ MPSoC platform.
- Added support for Arm Cortex-A73 MPCore Processor.
- Added support for Arm Cortex-A72 processor.
- Added support for Arm Cortex-A35 processor.
- Added support for Arm Cortex-A32 MPCore Processor.
- Enabled preloaded BL33 alternative boot flow, in which BL2 does not load
BL33 from non-volatile storage and BL31 hands execution over to a preloaded
BL33. The User Guide has been updated with an example of how to use this
option with a bootwrapped kernel.
- Added support to build TF-A on a Windows-based host machine.
- Updated Trusted Board Boot prototype implementation:
- Enabled the ability for a production ROM with TBBR enabled to boot test
software before a real ROTPK is deployed (e.g. manufacturing mode).
Added support to use ROTPK in certificate without verifying against the
platform value when ``ROTPK_NOT_DEPLOYED`` bit is set.
- Added support for non-volatile counter authentication to the
Authentication Module to protect against roll-back.
- Updated GICv3 support:
- Enabled processor power-down and automatic power-on using GICv3.
- Enabled G1S or G0 interrupts to be configured independently.
- Changed FVP default interrupt driver to be the GICv3-only driver.
**Note** the default build of TF-A will not be able to boot
Linux kernel with GICv2 FDT blob.
- Enabled wake-up from CPU_SUSPEND to stand-by by temporarily re-routing
interrupts and then restoring after resume.
Issues resolved since last release
^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Known issues
^^^^^^^^^^^^
- The version of the AEMv8 Base FVP used in this release resets the model
instead of terminating its execution in response to a shutdown request using
the PSCI ``SYSTEM_OFF`` API. This issue will be fixed in a future version of
the model.
- Building TF-A with compiler optimisations disabled (``-O0``) fails.
- TF-A cannot be built with mbed TLS version v2.3.0 due to build warnings
that the TF-A build system interprets as errors.
- TBBR is not currently supported when running TF-A in AArch32 state.
Version 1.2
-----------
New features
^^^^^^^^^^^^