blob: 754cf53b56f26f17d913374cc6cc462e9b896568 [file] [log] [blame]
/******************************************************************************
*
* Copyright 2001-2012 Broadcom Corporation
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************/
/******************************************************************************
*
* this file contains constants and definitions for the bte project
*
******************************************************************************/
#ifndef BTE_H
#define BTE_H
#include <pthread.h>
#include <semaphore.h>
#include <signal.h>
#include "bt_target.h"
/* By default on shutdown, the baud rate is reset to 115kbits. This should NOT
* be needed for platforms that kill the BTE driver and remove/reset BT chip.
*/
#ifndef BTE_RESET_BAUD_ON_BT_DISABLE
#define BTE_RESET_BAUD_ON_BT_DISABLE TRUE
#endif
/* Target Modes (based on jumper settings on hardware [see user manual])
* BTE BBY
* J3 J4 SW3-3 SW3-2 SW3-1
* --------------------------------------------
* BTE_MODE_SERIAL_APP, OUT OUT OFF OFF OFF
* BTE_MODE_APPL, IN OUT OFF OFF ON
* BTE_MODE_RESERVED, OUT IN OFF ON OFF
* BTE_MODE_SAMPLE_APPS, IN IN OFF ON ON
* BTE_MODE_DONGLE, not yet supported ON OFF OFF
* BTE_MODE_APPL_PROTOCOL_TRACE, * this is a fake mode *
* BTE_MODE_INVALID
*/
enum {
BTE_MODE_SERIAL_APP, /* Sample serial port application */
BTE_MODE_APPL, /* Target used with Tester through RPC */
BTE_MODE_RESERVED, /* Reserved */
BTE_MODE_SAMPLE_APPS, /* Sample applications (ICP/HSP) */
BTE_MODE_DONGLE, /* Dongle mode */
BTE_MODE_APPL_PROTOCOL_TRACE, /* Allow protocol tracing without rpc */
BTE_MODE_INVALID
};
extern volatile uint8_t
bte_target_mode; /* indicates the mode that the board is running in */
/* Startup options */
extern uint32_t bte_startup_options; /* Switch and jumper settings at startup */
void bte_get_startup_options(
uint32_t*
p_options); /* Platform specific function for getting startup options */
#define BTE_OPTIONS_TARGET_MODE_MASK \
0x00000007 /* bits 2-0 indicate target mode (QuickConnect: jp3 & jp4, BBY: \
SW3-1 & SW3-2)*/
/****************************************************************************
* Definitions to define which type of application gets built
****************************************************************************/
#define BUILD_HCITOOL FALSE
#define BUILD_L2PING FALSE
#define LINUX_FM_DRIVER_INCLUDED FALSE
/* hcisu userial operations. should probably go into bt_types to avoid
* collisions! */
#define BT_EVT_TO_HCISU_USERIAL_OP (0x0080 | BT_EVT_HCISU)
/* operation for above hcisu event */
#define BT_HCISU_USERIAL_OPEN \
(0) /* open serial port calling USERIAL_Open() \
*/
#define BT_HCISU_USERIAL_CLOSE (1) /* close userial port */
/* options associated with close op */
#define BT_HCISU_USERIAL_CL_NO_DIS_BT \
0 /* do not touch bt_wake and power gpio */
#define BT_HCISU_USERIAL_CL_DIS_BT \
1 /* put power and bt_wake into defined off state to preserve \
power */
/* status codes for callback */
#define BTE_HCISU_USERIAL_FAIL 0
#define BTE_HCISU_USERIAL_OK 1
typedef void(tUSERIAL_MSG_CBACK)(int status);
typedef struct tHCISU_USERIAL_MSG_tag {
BT_HDR hdr;
tUSERIAL_MSG_CBACK* p_cback;
uint8_t port; /* port number */
uint8_t op;
uint8_t option; /* option for operation. depends on operation */
} tHCISU_USERIAL_MSG;
extern void bte_hcisu_userial_oper(tUSERIAL_MSG_CBACK* p_cback, uint8_t port,
uint8_t op, uint8_t option);
/* Pointer to function for sending HCI commands and data to the HCI tranport */
extern int (*p_bte_hci_send)(uint16_t port, BT_HDR* p_msg);
// Initialize control block memory for each stack component.
extern void BTE_InitStack(void);
/* Protocol trace mask */
extern uint32_t bte_proto_trace_mask;
typedef struct tBAUD_REG_tag {
uint8_t DHBR;
uint8_t DLBR;
uint8_t ExplicitBaudRate0;
uint8_t ExplicitBaudRate1;
uint8_t ExplicitBaudRate2;
uint8_t ExplicitBaudRate3;
} tBAUD_REG;
extern const tBAUD_REG baud_rate_regs[];
#endif /* BTE_H */