/*
 * Copyright (C) 2016 The Android Open Source Project
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *      http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */

package android.hardware.health@1.0;

/**
 * Possible return values for optional HAL method(s) like
 * IHealth::energyCounter()
 */
enum Result : int32_t {
    SUCCESS,
    NOT_SUPPORTED,
    UNKNOWN,
};

/**
 * Possible values for Battery Status.
 * Note: These are currently in sync with BatteryManager and must not
 * be extended / altered.
 */
@export(name="", value_prefix="BATTERY_STATUS_")
enum BatteryStatus : int32_t {
    UNKNOWN = 1,
    CHARGING = 2,
    DISCHARGING = 3,
    /**
     * Battery is *not* charging - special case when charger is present
     * but battery isn't charging
     */
    NOT_CHARGING = 4,
    FULL = 5,
};

/**
 * Possible values for Battery Health.
 * Note: These are currently in sync with BatteryManager and must not
 * be extended / altered.
 */
@export(name="", value_prefix="BATTERY_HEALTH_")
enum BatteryHealth : int32_t {
    UNKNOWN = 1,
    GOOD = 2,
    OVERHEAT = 3,
    DEAD = 4,
    OVER_VOLTAGE = 5,
    /**
     * Battery experienced an unknown/unspecifid failure.
     */
    UNSPECIFIED_FAILURE = 6,
    COLD = 7,
};

struct HealthConfig {

    /**
     * periodicChoresIntervalFast is used while the device is not in
     * suspend, or in suspend and connected to a charger (to watch for battery
     * overheat due to charging)
     */
    int32_t periodicChoresIntervalFast;

    /**
     * periodicChoresIntervalSlow is used when the device is in suspend and
     * not connected to a charger (to watch for a battery drained to zero
     * remaining capacity).
     */
    int32_t periodicChoresIntervalSlow;

    /**
     * power_supply sysfs attribute file paths. Set these to specific paths
     * to use for the associated battery parameters. Clients must search
     * for appropriate power_supply attribute files to use, for any paths
     * left empty after the HAL is initialized.
     */

    /**
     * batteryStatusPath - file path to read battery charging status.
     * (POWER_SUPPLY_PROP_STATUS)
     */
    string batteryStatusPath;


    /**
     * batteryHealthPath - file path to read battery health.
     * (POWER_SUPPLY_PROP_HEALTH)
     */
    string batteryHealthPath;

    /**
     * batteryPresentPath - file path to read battery present status.
     * (POWER_SUPPLY_PROP_PRESENT)
     */
    string batteryPresentPath;


    /**
     * batteryCapacityPath - file path to read remaining battery capacity.
     * (POWER_SUPPLY_PROP_CAPACITY)
     */
    string batteryCapacityPath;

    /**
     * batteryVoltagePath - file path to read battery voltage.
     * (POWER_SUPPLY_PROP_VOLTAGE_NOW)
     */
    string batteryVoltagePath;

    /**
     * batteryTemperaturePath - file path to read battery temperature in tenths
     * of degree celcius. (POWER_SUPPLY_PROP_TEMP)
     */
    string batteryTemperaturePath;

    /**
     * batteryTechnologyPath - file path to read battery technology.
     * (POWER_SUPPLY_PROP_TECHNOLOGY)
     */
    string batteryTechnologyPath;

    /**
     * batteryCurrentNowPath - file path to read battery instantaneous current.
     * (POWER_SUPPLY_PROP_CURRENT_NOW)
     */
    string batteryCurrentNowPath;

    /**
     * batteryCurrentAvgPath - file path to read battery average current.
     * (POWER_SUPPLY_PROP_CURRENT_AVG)
     */
    string batteryCurrentAvgPath;

    /**
     * batteryChargeCounterPath - file path to read battery accumulated charge.
     * (POWER_SUPPLY_PROP_CHARGE_COUNTER)
     */
    string batteryChargeCounterPath;

    /**
     * batteryFullChargerPath - file path to read battery charge value when it
     * is considered to be full. (POWER_SUPPLY_PROP_CHARGE_FULL)
     */
    string batteryFullChargePath;

    /**
     * batteryCycleCountPath - file path to read battery charge cycle count.
     * (POWER_SUPPLY_PROP_CYCLE_COUNT)
     */
    string batteryCycleCountPath;
};

/**
 * The parameter to healthd mainloop update calls
 */
struct HealthInfo {
    /** AC charger state - 'true' if online */
    bool chargerAcOnline;

    /** USB charger state - 'true' if online */
    bool chargerUsbOnline;

    /** Wireless charger state - 'true' if online */
    bool chargerWirelessOnline;

    /** Maximum charging current supported by charger in uA */
    int32_t maxChargingCurrent;

    /** Maximum charging voltage supported by charger in uV */
    int32_t maxChargingVoltage;

    BatteryStatus batteryStatus;

    BatteryHealth batteryHealth;

    /** 'true' if battery is present */
    bool batteryPresent;

    /** Remaining battery capacity in percent */
    int32_t batteryLevel;

    /**
     * Instantaneous battery voltage in millivolts (mV).
     *
     * Historically, the unit of this field is microvolts (uV), but all
     * clients and implementations uses millivolts in practice, making it
     * the de-facto standard.
     */
    int32_t batteryVoltage;

    /** Instantaneous battery temperature in tenths of degree celcius */
    int32_t batteryTemperature;

    /** Instantaneous battery current in uA */
    int32_t batteryCurrent;

    /** Battery charge cycle count */
    int32_t batteryCycleCount;

    /** Battery charge value when it is considered to be "full" in uA-h */
    int32_t batteryFullCharge;

    /** Instantaneous battery capacity in uA-h */
    int32_t batteryChargeCounter;

    /** Battery technology, e.g. "Li-ion, Li-Poly" etc. */
    string batteryTechnology;
};