| # This file allows user to override the factory |
| |
| # defaults for the WLAN Driver |
| |
| |
| # Enable IMPS or not |
| gEnableImps=1 |
| |
| # Enable/Disable Idle Scan |
| |
| gEnableIdleScan=0 |
| |
| |
| # Increase sleep duration (seconds) during IMPS |
| # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
| # unnecessary if Idle Scan is disabled. |
| gImpsModSleepTime=0 |
| |
| |
| # Enable BMPS or not |
| gEnableBmps=1 |
| |
| # Enable suspend or not |
| |
| # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| |
| gEnableSuspend=3 |
| |
| |
| # Phy Mode (auto, b, g, n, etc) |
| # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| gDot11Mode=0 |
| |
| |
| # CSR Roaming Enable(1) Disable(0) |
| |
| gRoamingTime=0 |
| |
| |
| # Assigned MAC Addresses - This will be used until NV items are in place |
| |
| # Each byte of MAC address is represented in Hex format as XX |
| |
| Intf0MacAddress=000AF58989FF |
| Intf1MacAddress=000AF58989FE |
| Intf2MacAddress=000AF58989FD |
| |
| Intf3MacAddress=000AF58989FC |
| |
| # Set/Clear UAPSD mask |
| |
| UapsdMask=0 |
| |
| # UAPSD service interval for VO,VI, BE, BK traffic |
| |
| InfraUapsdVoSrvIntv=20 |
| |
| InfraUapsdViSrvIntv=40 |
| |
| # Flag to allow STA send AddTspec even when ACM is Off |
| gAddTSWhenACMIsOff=1 |
| |
| # Make 1x1 the default antenna configuration |
| |
| gNumRxAnt=1 |
| |
| |
| # Beacon filtering frequency (unit in beacon intervals) |
| |
| gNthBeaconFilter=50 |
| |
| |
| # Enable WAPI or not |
| |
| # WAPIIsEnabled=0 |
| |
| |
| # Flags to filter Mcast abd Bcast RX packets. |
| |
| # Value 0: No filtering, 1: Filter all Multicast. |
| |
| # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast |
| |
| McastBcastFilter=3 |
| |
| |
| #Flag to enable HostARPOffload feature or not |
| |
| hostArpOffload=1 |
| |
| |
| #SoftAP Related Parameters |
| |
| # AP MAc addr |
| |
| gAPMacAddr=000AF589dcab |
| |
| |
| # 802.11n Protection flag |
| |
| gEnableApProt=1 |
| |
| |
| #Enable OBSS protection |
| |
| gEnableApOBSSProt=1 |
| |
| |
| #Enable/Disable UAPSD for SoftAP |
| |
| gEnableApUapsd=1 |
| |
| |
| # Fixed Rate |
| |
| gFixedRate=0 |
| |
| |
| # Maximum Tx power |
| |
| # gTxPowerCap=30 |
| |
| |
| # Fragmentation Threshold |
| |
| # gFragmentationThreshold=2346 |
| |
| |
| # RTS threshold |
| |
| RTSThreshold=2347 |
| |
| |
| # Intra-BSS forward |
| |
| gDisableIntraBssFwd=0 |
| |
| |
| # WMM Enable/Disable |
| |
| WmmIsEnabled=0 |
| |
| |
| # 802.11d support |
| |
| g11dSupportEnabled=1 |
| |
| # CCX Support and fast transition |
| EseEnabled=0 |
| FastTransitionEnabled=1 |
| ImplicitQosIsEnabled=0 |
| gNeighborScanTimerPeriod=200 |
| |
| # default value of this parameter is zero to enable dynamic threshold allocation |
| # to set static roming threshold uncomment below parameter and set vaule |
| #gNeighborLookupThreshold=78 |
| |
| gNeighborScanChannelMinTime=20 |
| gNeighborScanChannelMaxTime=30 |
| |
| # Legacy (non-CCX, non-802.11r) Fast Roaming Support |
| # To enable, set FastRoamEnabled=1 |
| # To disable, set FastRoamEnabled=0 |
| FastRoamEnabled=1 |
| |
| #Check if the AP to which we are roaming is better than current AP in terms of RSSI. |
| #Checking is disabled if set to Zero.Otherwise it will use this value as to how better |
| #the RSSI of the new/roamable AP should be for roaming |
| RoamRssiDiff=5 |
| |
| # SAP Country code |
| |
| # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| |
| # Example |
| |
| # US Indoor, USI |
| |
| # Korea Outdoor, KRO |
| |
| # Japan without optional byte, JP |
| |
| # France without optional byte, FR |
| |
| #gAPCntryCode=USI |
| |
| |
| #Short Guard Interval Enable/disable |
| |
| gShortGI20Mhz=1 |
| |
| gShortGI40Mhz=1 |
| |
| |
| #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| |
| gAPAutoShutOff=0 |
| |
| |
| # SAP auto channel selection configuration |
| |
| # 0 = disable auto channel selection |
| |
| # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| |
| gApAutoChannelSelection=0 |
| |
| |
| # Listen Energy Detect Mode Configuration |
| |
| # Valid values 0-128 |
| |
| # 128 means disable Energy Detect feature |
| |
| # 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. |
| |
| # 10-128 are reserved. |
| |
| # The EDET threshold mapping is as follows in 3dB step: |
| |
| # 0 = -60 dBm |
| |
| # 1 = -63 dBm |
| |
| # 2 = -66 dBm |
| |
| # ... |
| |
| # 7 = -81 dBm |
| |
| # 8 = -84 dBm |
| |
| # 9 = -87 dBm |
| |
| # Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: |
| |
| # |
| |
| # Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. |
| |
| # |
| |
| gEnablePhyAgcListenMode=128 |
| |
| |
| #Preferred channel to start BT AMP AP mode (0 means, any channel) |
| |
| BtAmpPreferredChannel=0 |
| |
| |
| #Preferred band (both or 2.4 only or 5 only) |
| |
| BandCapability=0 |
| |
| |
| #Beacon Early Termination (1 = enable the BET feature, 0 = disable) |
| |
| enableBeaconEarlyTermination=1 |
| |
| beaconEarlyTerminationWakeInterval=11 |
| |
| |
| #Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable) |
| |
| gEnableBtAmp=0 |
| |
| |
| #SOFTAP Channel Range selection |
| |
| gAPChannelSelectStartChannel=1 |
| |
| gAPChannelSelectEndChannel=11 |
| |
| |
| #SOFTAP Channel Range selection Operating band |
| |
| # 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND 5: 5GHZ BAND |
| |
| gAPChannelSelectOperatingBand=0 |
| |
| |
| #Channel Bonding |
| gChannelBondingMode5GHz=1 |
| |
| gEnableModulatedDTIM = 3 |
| gMaxLIModulatedDTIM = 3 |
| gEnableDatainactivity = 200 |
| |
| #Enable Keep alive with non-zero period value |
| |
| gStaKeepAlivePeriod=30 |
| |
| |
| #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). |
| #For every 10 seconds DUT sends Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) |
| #For both active and power save clients. |
| |
| #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. |
| #If doesn't honor for 5 seconds then Driver remove client. |
| |
| #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still DUT try on |
| #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. |
| #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod +gGoLinkMonitorPeriod).. |
| |
| #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period |
| #where we send NULL frame. |
| |
| #gApLinkMonitorPeriod = 10 |
| |
| #gGoLinkMonitorPeriod = 10 |
| |
| #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. |
| #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. |
| gGoKeepAlivePeriod = 10 |
| |
| gApKeepAlivePeriod = 30 |
| #If set will start with active scan after driver load, otherwise will start with |
| |
| #passive scan to find out the domain |
| |
| #gEnableBypass11d=1 |
| |
| |
| #If set to 0, will not scan DFS channels |
| |
| gEnableDFSChnlScan=1 |
| |
| gEnableLogp=1 |
| |
| |
| # Enable Automatic Tx Power control |
| |
| gEnableAutomaticTxPowerControl=0 |
| |
| # 0 for OLPC 1 for CLPC and SCPC |
| gEnableCloseLoop=1 |
| |
| #Data Inactivity Timeout when in powersave (in ms) |
| gDataInactivityTimeout=200 |
| |
| gEnableLpwrImgTransition=1 |
| |
| # Scan Timing Parameters |
| # gPassiveMaxChannelTime=110 |
| # gPassiveMinChannelTime=60 |
| # Enable Tx LDPC |
| #gTxLdpcEnable = 1 for HT mode, 2 for VHT mode,3 for both HT and VHT |
| gTxLdpcEnable=3 |
| # gActiveMaxChannelTime=40 |
| # gActiveMinChannelTime=20 |
| |
| # Valid values are 2048,4096,8192 and so on |
| # Please don't use values other than the ones mentioned above |
| gMaxMediumTime=4096 |
| |
| # 802.11K support |
| gRrmEnable=1 |
| gRrmOperChanMax=8 |
| gRrmNonOperChanMax=8 |
| gRrmRandIntvl=100 |
| |
| #Scan offload |
| gEnableDirectedScanOffload=0 |
| |
| #FlexConnect Power Factor |
| #Default is set to 0 (disable) |
| gFlexConnectPowerFactor=0 |
| |
| gVhtChannelWidth=2 |
| |
| # VHT Tx/Rx MCS values |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gVhtRxMCS=2 |
| gVhtTxMCS=2 |
| |
| # Enable Tx beamforming |
| gTxBFEnable=1 |
| |
| #Enable/Disable TDLS Feature |
| gEnableTDLSSupport=1 |
| |
| #Enable/Disable TDLS Implicit Trigger |
| gEnableTDLSImplicitTrigger=0 |
| |
| #Enable/Disable TDLS WMM Mode |
| gEnableTDLSWmmMode=1 |
| |
| #Enable/Disable TDLS Buffer Sta |
| gEnableTDLSBufferSta=1 |
| |
| |
| END |
| |
| # Note: Configuration parser would not read anything past the END marker |
| |
