blob: f86f9e1e493ea1d437e41e76aa0c0bdc23757c1a [file] [log] [blame]
# This file allows user to override the factory
# defaults for the WLAN Driver
# Enable IMPS or not
gEnableImps=1
# Enable/Disable Idle Scan
gEnableIdleScan=0
# Enable/Disable vsta based on MAX Assoc limit
gEnableVSTASupport=1
# Increase sleep duration (seconds) during IMPS
# 0 implies no periodic wake up from IMPS. Periodic wakeup is
# unnecessary if Idle Scan is disabled.
gImpsModSleepTime=0
# Enable BMPS or not
gEnableBmps=1
# Enable suspend or not
# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter
gEnableSuspend=3
# Phy Mode (auto, b, g, n, etc)
# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac
gDot11Mode=0
# CSR Roaming Enable(1) Disable(0)
gRoamingTime=0
# Assigned MAC Addresses - This will be used until NV items are in place
# Each byte of MAC address is represented in Hex format as XX
Intf0MacAddress=000AF58989FF
Intf1MacAddress=000AF58989FE
Intf2MacAddress=000AF58989FD
Intf3MacAddress=000AF58989FC
# UAPSD service interval for VO,VI, BE, BK traffic
InfraUapsdVoSrvIntv=0
InfraUapsdViSrvIntv=0
InfraUapsdBeSrvIntv=0
InfraUapsdBkSrvIntv=0
# Flag to allow STA send AddTspec even when ACM is Off
gAddTSWhenACMIsOff=1
# Make 1x1 the default antenna configuration
gNumRxAnt=1
# Beacon filtering frequency (unit in beacon intervals)
gNthBeaconFilter=50
# Enable WAPI or not
# WAPIIsEnabled=0
# Flags to filter Mcast abd Bcast RX packets.
# Value 0: No filtering, 1: Filter all Multicast.
# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast
McastBcastFilter=3
#Flag to enable HostARPOffload feature or not
hostArpOffload=1
#Flag to enable HostNSOffload feature or not
hostNSOffload=0
#SoftAP Related Parameters
# AP MAc addr
gAPMacAddr=000AF589dcab
# 802.11n Protection flag
gEnableApProt=1
#Enable OBSS protection
gEnableApOBSSProt=1
#Enable/Disable UAPSD for SoftAP
gEnableApUapsd=1
# Fixed Rate
gFixedRate=0
# Maximum Tx power
# gTxPowerCap=30
# Fragmentation Threshold
# gFragmentationThreshold=2346
# RTS threshold
RTSThreshold=2347
# Intra-BSS forward
gDisableIntraBssFwd=0
# WMM Enable/Disable
WmmIsEnabled=0
# 802.11d support
g11dSupportEnabled=1
# 802.11h support
g11hSupportEnabled=1
# ESE Support and fast transition
EseEnabled=0
ImplicitQosIsEnabled=0
gNeighborScanTimerPeriod=200
gNeighborLookupThreshold=76
gNeighborReassocThreshold=81
gNeighborScanChannelMinTime=20
gNeighborScanChannelMaxTime=30
gMaxNeighborReqTries=3
# Legacy (non-ESE, non-802.11r) Fast Roaming Support
# To enable, set FastRoamEnabled=1
# To disable, set FastRoamEnabled=0
FastRoamEnabled=1
#Check if the AP to which we are roaming is better than current AP in terms of RSSI.
#Checking is disabled if set to Zero.Otherwise it will use this value as to how better
#the RSSI of the new/roamable AP should be for roaming
RoamRssiDiff=3
# If the RSSI of any available candidate is better than currently associated
# AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without
# registering for reassoc threshold).
# NOTE: Value of 0 means that we would register for reassoc threshold.
gImmediateRoamRssiDiff=10
# To enable, set gRoamIntraBand=1 (Roaming within band)
# To disable, set gRoamIntraBand=0 (Roaming across band)
gRoamIntraBand=0
#SAP Country code
# Default Country Code is 2 bytes, 3rd byte is optional indoor or out door.
# Example
# US Indoor, USI
# Korea Outdoor, KRO
# Japan without optional byte, JP
# France without optional byte, FR
#gAPCntryCode=USI
#Short Guard Interval Enable/disable
gShortGI20Mhz=1
gShortGI40Mhz=1
#Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled
gAPAutoShutOff=0
# SAP auto channel selection configuration
# 0 = disable auto channel selection
# 1 = enable auto channel selection, channel provided by supplicant will be ignored
gApAutoChannelSelection=1
# Listen Energy Detect Mode Configuration
# Valid values 0-128
# 128 means disable Energy Detect feature
# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled.
# 10-128 are reserved.
# The EDET threshold mapping is as follows in 3dB step:
# 0 = -60 dBm
# 1 = -63 dBm
# 2 = -66 dBm
# ...
# 7 = -81 dBm
# 8 = -84 dBm
# 9 = -87 dBm
# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as:
#
# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm.
#
gEnablePhyAgcListenMode=128
#Preferred channel to start BT AMP AP mode (0 means, any channel)
BtAmpPreferredChannel=0
#Preferred band (both or 2.4 only or 5 only)
BandCapability=0
#Beacon Early Termination (1 = enable the BET feature, 0 = disable)
enableBeaconEarlyTermination=0
beaconEarlyTerminationWakeInterval=3
#Bluetooth Alternate Mac Phy (1 = enable the BT AMP feature, 0 = disable)
gEnableBtAmp=0
#SOFTAP Channel Range selection
gAPChannelSelectStartChannel=1
gAPChannelSelectEndChannel=11
#SOFTAP Channel Range selection Operating band
# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND
gAPChannelSelectOperatingBand=0
#Channel Bonding
gChannelBondingMode5GHz=1
gChannelBondingMode24GHz=1
#Enable Keep alive with non-zero period value
#gStaKeepAlivePeriod = 30
#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds).
#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.)
#For both active and power save clients.
#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit.
#If doesn't honor for 5 seconds then DUT remove client.
#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on
#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames.
#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod)..
#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period
#where we send NULL frame.
#gApLinkMonitorPeriod = 10
#gGoLinkMonitorPeriod = 10
#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not.
#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod.
gGoKeepAlivePeriod=30
gApKeepAlivePeriod=10
#If set will start with active scan after driver load, otherwise will start with
#passive scan to find out the domain
gEnableBypass11d=1
#If set to 0, will not scan DFS channels
gEnableDFSChnlScan=1
gVhtChannelWidth=2
gEnableLogp=1
# Enable Automatic Tx Power control
gEnableAutomaticTxPowerControl=0
# 0 for OLPC 1 for CLPC and SCPC
gEnableCloseLoop=1
#Data Inactivity Timeout when in powersave (in ms)
gDataInactivityTimeout=200
# VHT Tx/Rx MCS values
# Valid values are 0,1,2. If commented out, the default value is 0.
# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9
gVhtRxMCS=2
gVhtTxMCS=2
# Enable CRDA regulatory support by settings default country code
#gCrdaDefaultCountryCode=TW
# Scan Timing Parameters
# gPassiveMaxChannelTime=110
# gPassiveMinChannelTime=60
# gActiveMaxChannelTime=40
# gActiveMinChannelTime=20
#If set to 0, MCC is not allowed.
gEnableMCCMode=1
# 1=enable STBC; 0=disable STBC
gEnableRXSTBC=1
# Enable Active mode offload
gEnableActiveModeOffload=1
#Enable Scan Results Aging based on timer
#Timer value is in seconds
#If Set to 0 it will not enable the feature
gScanAgingTime=0
#Enable Power saving mechanism Based on Android Framework
#If set to 0 Driver internally control the Power saving mechanism
#If set to 1 Android Framwrok control the Power saving mechanism
isAndroidPsEn=0
#disable LDPC in STA mode if the AP is TXBF capable
gDisableLDPCWithTxbfAP=1
#Enable thermal mitigation
gThermalMitigationEnable=1
gEnableFastRoamInConcurrency=1
#List of Country codes for which 11ac needs to be disabled
#Each country code must be delimited by comma(,)
gListOfNon11acCountryCode=RU,UA,ZA
#Maxium Channel time in msec
gMaxMediumTime = 5480
# 802.11K support
gRrmEnable=1
gRrmOperChanMax=8
gRrmNonOperChanMax=8
gRrmRandIntvl=100
#Scan offload
gEnableDirectedScanOffload=0
#FlexConnect Power Factor
#Default is set to 0 (disable)
gFlexConnectPowerFactor=0
#SAP/P2P-GO mode traffic monitor
gEnableTrafficMonitor=1
gTrafficIdleTimeout=3000
#Disable/Enable Strict FCC Regulatory
# 0 to disable, 1 to enable
gEnableStrictRegulatoryForFCC=1
#Enable/Disable Modulated DTIM feature
gEnableModulatedDTIM=3
#max LI value for modulated DTIM
gMaxLIModulatedDTIM=3
#Enable/Disable Link Layer Statistics Feature
gEnableLLStats=1
#Enable/Disable EXTScan Feature
gEnableEXTScan=1
#Enable/Disable RTS-CTS for HT,VHT
#Bit mask value to enable RTS/CTS for different modes
#For 2.4 GHz, HT20 - 0x0001 i.e 1, for 2.4 GHz, HT40 - 0x0002 i.e 2
#For 2.4 GHz, VHT20 - 0x0004 i.e 4, for 2.4 GHz, VHT40 - 0x0008 i.e 8
#For 5 GHz, HT20 - 0x0100 i.e 256, for 5 GHz, HT40 - 0x0200 i.e 512
#For 5 GHz, VHT20 - 0x0400 i.e 1024, for 5 GHz, VHT40 - 0x0800 i.e 2048
#For 5 GHz, VHT80 - 0x1000 i.e 4096
#Can be enabled for multiple modes
#For enabling in both HT20 and HT40 of 2.4 GHz - 0x0003 i.e 3
#Default is set to 0 (disable)
gEnableRtsCtsHtVht=0
END
# Note: Configuration parser would not read anything past the END marker