blob: 280cb845fb04f484224a86cb37dc65b35a46d96b [file] [log] [blame]
/*
* SDIO spec header file
* Protocol and standard (common) device definitions
*
* Copyright (C) 1999-2010, Broadcom Corporation
*
* Unless you and Broadcom execute a separate written software license
* agreement governing use of this software, this software is licensed to you
* under the terms of the GNU General Public License version 2 (the "GPL"),
* available at http://www.broadcom.com/licenses/GPLv2.php, with the
* following added to such license:
*
* As a special exception, the copyright holders of this software give you
* permission to link this software with independent modules, and to copy and
* distribute the resulting executable under terms of your choice, provided that
* you also meet, for each linked independent module, the terms and conditions of
* the license of that module. An independent module is a module which is not
* derived from this software. The special exception does not apply to any
* modifications of the software.
*
* Notwithstanding the above, under no circumstances may you combine this
* software in any way with any other Broadcom software provided under a license
* other than the GPL, without Broadcom's express prior written consent.
*
* $Id: sdio.h,v 13.24.4.1.4.1.16.1 2009/08/12 01:08:02 Exp $
*/
#ifndef _SDIO_H
#define _SDIO_H
/* CCCR structure for function 0 */
typedef volatile struct {
uint8 cccr_sdio_rev; /* RO, cccr and sdio revision */
uint8 sd_rev; /* RO, sd spec revision */
uint8 io_en; /* I/O enable */
uint8 io_rdy; /* I/O ready reg */
uint8 intr_ctl; /* Master and per function interrupt enable control */
uint8 intr_status; /* RO, interrupt pending status */
uint8 io_abort; /* read/write abort or reset all functions */
uint8 bus_inter; /* bus interface control */
uint8 capability; /* RO, card capability */
uint8 cis_base_low; /* 0x9 RO, common CIS base address, LSB */
uint8 cis_base_mid;
uint8 cis_base_high; /* 0xB RO, common CIS base address, MSB */
/* suspend/resume registers */
uint8 bus_suspend; /* 0xC */
uint8 func_select; /* 0xD */
uint8 exec_flag; /* 0xE */
uint8 ready_flag; /* 0xF */
uint8 fn0_blk_size[2]; /* 0x10(LSB), 0x11(MSB) */
uint8 power_control; /* 0x12 (SDIO version 1.10) */
uint8 speed_control; /* 0x13 */
} sdio_regs_t;
/* SDIO Device CCCR offsets */
#define SDIOD_CCCR_REV 0x00
#define SDIOD_CCCR_SDREV 0x01
#define SDIOD_CCCR_IOEN 0x02
#define SDIOD_CCCR_IORDY 0x03
#define SDIOD_CCCR_INTEN 0x04
#define SDIOD_CCCR_INTPEND 0x05
#define SDIOD_CCCR_IOABORT 0x06
#define SDIOD_CCCR_BICTRL 0x07
#define SDIOD_CCCR_CAPABLITIES 0x08
#define SDIOD_CCCR_CISPTR_0 0x09
#define SDIOD_CCCR_CISPTR_1 0x0A
#define SDIOD_CCCR_CISPTR_2 0x0B
#define SDIOD_CCCR_BUSSUSP 0x0C
#define SDIOD_CCCR_FUNCSEL 0x0D
#define SDIOD_CCCR_EXECFLAGS 0x0E
#define SDIOD_CCCR_RDYFLAGS 0x0F
#define SDIOD_CCCR_BLKSIZE_0 0x10
#define SDIOD_CCCR_BLKSIZE_1 0x11
#define SDIOD_CCCR_POWER_CONTROL 0x12
#define SDIOD_CCCR_SPEED_CONTROL 0x13
/* Broadcom extensions (corerev >= 1) */
#define SDIOD_CCCR_BRCM_SEPINT 0xf2
/* cccr_sdio_rev */
#define SDIO_REV_SDIOID_MASK 0xf0 /* SDIO spec revision number */
#define SDIO_REV_CCCRID_MASK 0x0f /* CCCR format version number */
/* sd_rev */
#define SD_REV_PHY_MASK 0x0f /* SD format version number */
/* io_en */
#define SDIO_FUNC_ENABLE_1 0x02 /* function 1 I/O enable */
#define SDIO_FUNC_ENABLE_2 0x04 /* function 2 I/O enable */
/* io_rdys */
#define SDIO_FUNC_READY_1 0x02 /* function 1 I/O ready */
#define SDIO_FUNC_READY_2 0x04 /* function 2 I/O ready */
/* intr_ctl */
#define INTR_CTL_MASTER_EN 0x1 /* interrupt enable master */
#define INTR_CTL_FUNC1_EN 0x2 /* interrupt enable for function 1 */
#define INTR_CTL_FUNC2_EN 0x4 /* interrupt enable for function 2 */
/* intr_status */
#define INTR_STATUS_FUNC1 0x2 /* interrupt pending for function 1 */
#define INTR_STATUS_FUNC2 0x4 /* interrupt pending for function 2 */
/* io_abort */
#define IO_ABORT_RESET_ALL 0x08 /* I/O card reset */
#define IO_ABORT_FUNC_MASK 0x07 /* abort selction: function x */
/* bus_inter */
#define BUS_CARD_DETECT_DIS 0x80 /* Card Detect disable */
#define BUS_SPI_CONT_INTR_CAP 0x40 /* support continuous SPI interrupt */
#define BUS_SPI_CONT_INTR_EN 0x20 /* continuous SPI interrupt enable */
#define BUS_SD_DATA_WIDTH_MASK 0x03 /* bus width mask */
#define BUS_SD_DATA_WIDTH_4BIT 0x02 /* bus width 4-bit mode */
#define BUS_SD_DATA_WIDTH_1BIT 0x00 /* bus width 1-bit mode */
/* capability */
#define SDIO_CAP_4BLS 0x80 /* 4-bit support for low speed card */
#define SDIO_CAP_LSC 0x40 /* low speed card */
#define SDIO_CAP_E4MI 0x20 /* enable interrupt between block of data in 4-bit mode */
#define SDIO_CAP_S4MI 0x10 /* support interrupt between block of data in 4-bit mode */
#define SDIO_CAP_SBS 0x08 /* support suspend/resume */
#define SDIO_CAP_SRW 0x04 /* support read wait */
#define SDIO_CAP_SMB 0x02 /* support multi-block transfer */
#define SDIO_CAP_SDC 0x01 /* Support Direct commands during multi-byte transfer */
/* power_control */
#define SDIO_POWER_SMPC 0x01 /* supports master power control (RO) */
#define SDIO_POWER_EMPC 0x02 /* enable master power control (allow > 200mA) (RW) */
/* speed_control (control device entry into high-speed clocking mode) */
#define SDIO_SPEED_SHS 0x01 /* supports high-speed [clocking] mode (RO) */
#define SDIO_SPEED_EHS 0x02 /* enable high-speed [clocking] mode (RW) */
/* brcm sepint */
#define SDIO_SEPINT_MASK 0x01 /* route sdpcmdev intr onto separate pad (chip-specific) */
#define SDIO_SEPINT_OE 0x02 /* 1 asserts output enable for above pad */
#define SDIO_SEPINT_ACT_HI 0x04 /* use active high interrupt level instead of active low */
/* FBR structure for function 1-7, FBR addresses and register offsets */
typedef volatile struct {
uint8 devctr; /* device interface, CSA control */
uint8 ext_dev; /* extended standard I/O device type code */
uint8 pwr_sel; /* power selection support */
uint8 PAD[6]; /* reserved */
uint8 cis_low; /* CIS LSB */
uint8 cis_mid;
uint8 cis_high; /* CIS MSB */
uint8 csa_low; /* code storage area, LSB */
uint8 csa_mid;
uint8 csa_high; /* code storage area, MSB */
uint8 csa_dat_win; /* data access window to function */
uint8 fnx_blk_size[2]; /* block size, little endian */
} sdio_fbr_t;
/* Maximum number of I/O funcs */
#define SDIOD_MAX_IOFUNCS 7
/* SDIO Device FBR Start Address */
#define SDIOD_FBR_STARTADDR 0x100
/* SDIO Device FBR Size */
#define SDIOD_FBR_SIZE 0x100
/* Macro to calculate FBR register base */
#define SDIOD_FBR_BASE(n) ((n) * 0x100)
/* Function register offsets */
#define SDIOD_FBR_DEVCTR 0x00 /* basic info for function */
#define SDIOD_FBR_EXT_DEV 0x01 /* extended I/O device code */
#define SDIOD_FBR_PWR_SEL 0x02 /* power selection bits */
/* SDIO Function CIS ptr offset */
#define SDIOD_FBR_CISPTR_0 0x09
#define SDIOD_FBR_CISPTR_1 0x0A
#define SDIOD_FBR_CISPTR_2 0x0B
/* Code Storage Area pointer */
#define SDIOD_FBR_CSA_ADDR_0 0x0C
#define SDIOD_FBR_CSA_ADDR_1 0x0D
#define SDIOD_FBR_CSA_ADDR_2 0x0E
#define SDIOD_FBR_CSA_DATA 0x0F
/* SDIO Function I/O Block Size */
#define SDIOD_FBR_BLKSIZE_0 0x10
#define SDIOD_FBR_BLKSIZE_1 0x11
/* devctr */
#define SDIOD_FBR_DEVCTR_DIC 0x0f /* device interface code */
#define SDIOD_FBR_DECVTR_CSA 0x40 /* CSA support flag */
#define SDIOD_FBR_DEVCTR_CSA_EN 0x80 /* CSA enabled */
/* interface codes */
#define SDIOD_DIC_NONE 0 /* SDIO standard interface is not supported */
#define SDIOD_DIC_UART 1
#define SDIOD_DIC_BLUETOOTH_A 2
#define SDIOD_DIC_BLUETOOTH_B 3
#define SDIOD_DIC_GPS 4
#define SDIOD_DIC_CAMERA 5
#define SDIOD_DIC_PHS 6
#define SDIOD_DIC_WLAN 7
#define SDIOD_DIC_EXT 0xf /* extended device interface, read ext_dev register */
/* pwr_sel */
#define SDIOD_PWR_SEL_SPS 0x01 /* supports power selection */
#define SDIOD_PWR_SEL_EPS 0x02 /* enable power selection (low-current mode) */
/* misc defines */
#define SDIO_FUNC_0 0
#define SDIO_FUNC_1 1
#define SDIO_FUNC_2 2
#define SDIO_FUNC_3 3
#define SDIO_FUNC_4 4
#define SDIO_FUNC_5 5
#define SDIO_FUNC_6 6
#define SDIO_FUNC_7 7
#define SD_CARD_TYPE_UNKNOWN 0 /* bad type or unrecognized */
#define SD_CARD_TYPE_IO 1 /* IO only card */
#define SD_CARD_TYPE_MEMORY 2 /* memory only card */
#define SD_CARD_TYPE_COMBO 3 /* IO and memory combo card */
#define SDIO_MAX_BLOCK_SIZE 2048 /* maximum block size for block mode operation */
#define SDIO_MIN_BLOCK_SIZE 1 /* minimum block size for block mode operation */
/* Card registers: status bit position */
#define CARDREG_STATUS_BIT_OUTOFRANGE 31
#define CARDREG_STATUS_BIT_COMCRCERROR 23
#define CARDREG_STATUS_BIT_ILLEGALCOMMAND 22
#define CARDREG_STATUS_BIT_ERROR 19
#define CARDREG_STATUS_BIT_IOCURRENTSTATE3 12
#define CARDREG_STATUS_BIT_IOCURRENTSTATE2 11
#define CARDREG_STATUS_BIT_IOCURRENTSTATE1 10
#define CARDREG_STATUS_BIT_IOCURRENTSTATE0 9
#define CARDREG_STATUS_BIT_FUN_NUM_ERROR 4
#define SD_CMD_GO_IDLE_STATE 0 /* mandatory for SDIO */
#define SD_CMD_SEND_OPCOND 1
#define SD_CMD_MMC_SET_RCA 3
#define SD_CMD_IO_SEND_OP_COND 5 /* mandatory for SDIO */
#define SD_CMD_SELECT_DESELECT_CARD 7
#define SD_CMD_SEND_CSD 9
#define SD_CMD_SEND_CID 10
#define SD_CMD_STOP_TRANSMISSION 12
#define SD_CMD_SEND_STATUS 13
#define SD_CMD_GO_INACTIVE_STATE 15
#define SD_CMD_SET_BLOCKLEN 16
#define SD_CMD_READ_SINGLE_BLOCK 17
#define SD_CMD_READ_MULTIPLE_BLOCK 18
#define SD_CMD_WRITE_BLOCK 24
#define SD_CMD_WRITE_MULTIPLE_BLOCK 25
#define SD_CMD_PROGRAM_CSD 27
#define SD_CMD_SET_WRITE_PROT 28
#define SD_CMD_CLR_WRITE_PROT 29
#define SD_CMD_SEND_WRITE_PROT 30
#define SD_CMD_ERASE_WR_BLK_START 32
#define SD_CMD_ERASE_WR_BLK_END 33
#define SD_CMD_ERASE 38
#define SD_CMD_LOCK_UNLOCK 42
#define SD_CMD_IO_RW_DIRECT 52 /* mandatory for SDIO */
#define SD_CMD_IO_RW_EXTENDED 53 /* mandatory for SDIO */
#define SD_CMD_APP_CMD 55
#define SD_CMD_GEN_CMD 56
#define SD_CMD_READ_OCR 58
#define SD_CMD_CRC_ON_OFF 59 /* mandatory for SDIO */
#define SD_ACMD_SD_STATUS 13
#define SD_ACMD_SEND_NUM_WR_BLOCKS 22
#define SD_ACMD_SET_WR_BLOCK_ERASE_CNT 23
#define SD_ACMD_SD_SEND_OP_COND 41
#define SD_ACMD_SET_CLR_CARD_DETECT 42
#define SD_ACMD_SEND_SCR 51
/* argument for SD_CMD_IO_RW_DIRECT and SD_CMD_IO_RW_EXTENDED */
#define SD_IO_OP_READ 0 /* Read_Write: Read */
#define SD_IO_OP_WRITE 1 /* Read_Write: Write */
#define SD_IO_RW_NORMAL 0 /* no RAW */
#define SD_IO_RW_RAW 1 /* RAW */
#define SD_IO_BYTE_MODE 0 /* Byte Mode */
#define SD_IO_BLOCK_MODE 1 /* BlockMode */
#define SD_IO_FIXED_ADDRESS 0 /* fix Address */
#define SD_IO_INCREMENT_ADDRESS 1 /* IncrementAddress */
/* build SD_CMD_IO_RW_DIRECT Argument */
#define SDIO_IO_RW_DIRECT_ARG(rw, raw, func, addr, data) \
((((rw) & 1) << 31) | (((func) & 0x7) << 28) | (((raw) & 1) << 27) | \
(((addr) & 0x1FFFF) << 9) | ((data) & 0xFF))
/* build SD_CMD_IO_RW_EXTENDED Argument */
#define SDIO_IO_RW_EXTENDED_ARG(rw, blk, func, addr, inc_addr, count) \
((((rw) & 1) << 31) | (((func) & 0x7) << 28) | (((blk) & 1) << 27) | \
(((inc_addr) & 1) << 26) | (((addr) & 0x1FFFF) << 9) | ((count) & 0x1FF))
/* SDIO response parameters */
#define SD_RSP_NO_NONE 0
#define SD_RSP_NO_1 1
#define SD_RSP_NO_2 2
#define SD_RSP_NO_3 3
#define SD_RSP_NO_4 4
#define SD_RSP_NO_5 5
#define SD_RSP_NO_6 6
/* Modified R6 response (to CMD3) */
#define SD_RSP_MR6_COM_CRC_ERROR 0x8000
#define SD_RSP_MR6_ILLEGAL_COMMAND 0x4000
#define SD_RSP_MR6_ERROR 0x2000
/* Modified R1 in R4 Response (to CMD5) */
#define SD_RSP_MR1_SBIT 0x80
#define SD_RSP_MR1_PARAMETER_ERROR 0x40
#define SD_RSP_MR1_RFU5 0x20
#define SD_RSP_MR1_FUNC_NUM_ERROR 0x10
#define SD_RSP_MR1_COM_CRC_ERROR 0x08
#define SD_RSP_MR1_ILLEGAL_COMMAND 0x04
#define SD_RSP_MR1_RFU1 0x02
#define SD_RSP_MR1_IDLE_STATE 0x01
/* R5 response (to CMD52 and CMD53) */
#define SD_RSP_R5_COM_CRC_ERROR 0x80
#define SD_RSP_R5_ILLEGAL_COMMAND 0x40
#define SD_RSP_R5_IO_CURRENTSTATE1 0x20
#define SD_RSP_R5_IO_CURRENTSTATE0 0x10
#define SD_RSP_R5_ERROR 0x08
#define SD_RSP_R5_RFU 0x04
#define SD_RSP_R5_FUNC_NUM_ERROR 0x02
#define SD_RSP_R5_OUT_OF_RANGE 0x01
#define SD_RSP_R5_ERRBITS 0xCB
/* ------------------------------------------------
* SDIO Commands and responses
*
* I/O only commands are:
* CMD0, CMD3, CMD5, CMD7, CMD15, CMD52, CMD53
* ------------------------------------------------
*/
/* SDIO Commands */
#define SDIOH_CMD_0 0
#define SDIOH_CMD_3 3
#define SDIOH_CMD_5 5
#define SDIOH_CMD_7 7
#define SDIOH_CMD_15 15
#define SDIOH_CMD_52 52
#define SDIOH_CMD_53 53
#define SDIOH_CMD_59 59
/* SDIO Command Responses */
#define SDIOH_RSP_NONE 0
#define SDIOH_RSP_R1 1
#define SDIOH_RSP_R2 2
#define SDIOH_RSP_R3 3
#define SDIOH_RSP_R4 4
#define SDIOH_RSP_R5 5
#define SDIOH_RSP_R6 6
/*
* SDIO Response Error flags
*/
#define SDIOH_RSP5_ERROR_FLAGS 0xCB
/* ------------------------------------------------
* SDIO Command structures. I/O only commands are:
*
* CMD0, CMD3, CMD5, CMD7, CMD15, CMD52, CMD53
* ------------------------------------------------
*/
#define CMD5_OCR_M BITFIELD_MASK(24)
#define CMD5_OCR_S 0
#define CMD7_RCA_M BITFIELD_MASK(16)
#define CMD7_RCA_S 16
#define CMD_15_RCA_M BITFIELD_MASK(16)
#define CMD_15_RCA_S 16
#define CMD52_DATA_M BITFIELD_MASK(8) /* Bits [7:0] - Write Data/Stuff bits of CMD52
*/
#define CMD52_DATA_S 0
#define CMD52_REG_ADDR_M BITFIELD_MASK(17) /* Bits [25:9] - register address */
#define CMD52_REG_ADDR_S 9
#define CMD52_RAW_M BITFIELD_MASK(1) /* Bit 27 - Read after Write flag */
#define CMD52_RAW_S 27
#define CMD52_FUNCTION_M BITFIELD_MASK(3) /* Bits [30:28] - Function number */
#define CMD52_FUNCTION_S 28
#define CMD52_RW_FLAG_M BITFIELD_MASK(1) /* Bit 31 - R/W flag */
#define CMD52_RW_FLAG_S 31
#define CMD53_BYTE_BLK_CNT_M BITFIELD_MASK(9) /* Bits [8:0] - Byte/Block Count of CMD53 */
#define CMD53_BYTE_BLK_CNT_S 0
#define CMD53_REG_ADDR_M BITFIELD_MASK(17) /* Bits [25:9] - register address */
#define CMD53_REG_ADDR_S 9
#define CMD53_OP_CODE_M BITFIELD_MASK(1) /* Bit 26 - R/W Operation Code */
#define CMD53_OP_CODE_S 26
#define CMD53_BLK_MODE_M BITFIELD_MASK(1) /* Bit 27 - Block Mode */
#define CMD53_BLK_MODE_S 27
#define CMD53_FUNCTION_M BITFIELD_MASK(3) /* Bits [30:28] - Function number */
#define CMD53_FUNCTION_S 28
#define CMD53_RW_FLAG_M BITFIELD_MASK(1) /* Bit 31 - R/W flag */
#define CMD53_RW_FLAG_S 31
/* ------------------------------------------------------
* SDIO Command Response structures for SD1 and SD4 modes
* -----------------------------------------------------
*/
#define RSP4_IO_OCR_M BITFIELD_MASK(24) /* Bits [23:0] - Card's OCR Bits [23:0] */
#define RSP4_IO_OCR_S 0
#define RSP4_STUFF_M BITFIELD_MASK(3) /* Bits [26:24] - Stuff bits */
#define RSP4_STUFF_S 24
#define RSP4_MEM_PRESENT_M BITFIELD_MASK(1) /* Bit 27 - Memory present */
#define RSP4_MEM_PRESENT_S 27
#define RSP4_NUM_FUNCS_M BITFIELD_MASK(3) /* Bits [30:28] - Number of I/O funcs */
#define RSP4_NUM_FUNCS_S 28
#define RSP4_CARD_READY_M BITFIELD_MASK(1) /* Bit 31 - SDIO card ready */
#define RSP4_CARD_READY_S 31
#define RSP6_STATUS_M BITFIELD_MASK(16) /* Bits [15:0] - Card status bits [19,22,23,12:0]
*/
#define RSP6_STATUS_S 0
#define RSP6_IO_RCA_M BITFIELD_MASK(16) /* Bits [31:16] - RCA bits[31-16] */
#define RSP6_IO_RCA_S 16
#define RSP1_AKE_SEQ_ERROR_M BITFIELD_MASK(1) /* Bit 3 - Authentication seq error */
#define RSP1_AKE_SEQ_ERROR_S 3
#define RSP1_APP_CMD_M BITFIELD_MASK(1) /* Bit 5 - Card expects ACMD */
#define RSP1_APP_CMD_S 5
#define RSP1_READY_FOR_DATA_M BITFIELD_MASK(1) /* Bit 8 - Ready for data (buff empty) */
#define RSP1_READY_FOR_DATA_S 8
#define RSP1_CURR_STATE_M BITFIELD_MASK(4) /* Bits [12:9] - State of card
* when Cmd was received
*/
#define RSP1_CURR_STATE_S 9
#define RSP1_EARSE_RESET_M BITFIELD_MASK(1) /* Bit 13 - Erase seq cleared */
#define RSP1_EARSE_RESET_S 13
#define RSP1_CARD_ECC_DISABLE_M BITFIELD_MASK(1) /* Bit 14 - Card ECC disabled */
#define RSP1_CARD_ECC_DISABLE_S 14
#define RSP1_WP_ERASE_SKIP_M BITFIELD_MASK(1) /* Bit 15 - Partial blocks erased due to W/P */
#define RSP1_WP_ERASE_SKIP_S 15
#define RSP1_CID_CSD_OVERW_M BITFIELD_MASK(1) /* Bit 16 - Illegal write to CID or R/O bits
* of CSD
*/
#define RSP1_CID_CSD_OVERW_S 16
#define RSP1_ERROR_M BITFIELD_MASK(1) /* Bit 19 - General/Unknown error */
#define RSP1_ERROR_S 19
#define RSP1_CC_ERROR_M BITFIELD_MASK(1) /* Bit 20 - Internal Card Control error */
#define RSP1_CC_ERROR_S 20
#define RSP1_CARD_ECC_FAILED_M BITFIELD_MASK(1) /* Bit 21 - Card internal ECC failed
* to correct data
*/
#define RSP1_CARD_ECC_FAILED_S 21
#define RSP1_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 22 - Cmd not legal for the card state */
#define RSP1_ILLEGAL_CMD_S 22
#define RSP1_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 23 - CRC check of previous command failed
*/
#define RSP1_COM_CRC_ERROR_S 23
#define RSP1_LOCK_UNLOCK_FAIL_M BITFIELD_MASK(1) /* Bit 24 - Card lock-unlock Cmd Seq error */
#define RSP1_LOCK_UNLOCK_FAIL_S 24
#define RSP1_CARD_LOCKED_M BITFIELD_MASK(1) /* Bit 25 - Card locked by the host */
#define RSP1_CARD_LOCKED_S 25
#define RSP1_WP_VIOLATION_M BITFIELD_MASK(1) /* Bit 26 - Attempt to program
* write-protected blocks
*/
#define RSP1_WP_VIOLATION_S 26
#define RSP1_ERASE_PARAM_M BITFIELD_MASK(1) /* Bit 27 - Invalid erase blocks */
#define RSP1_ERASE_PARAM_S 27
#define RSP1_ERASE_SEQ_ERR_M BITFIELD_MASK(1) /* Bit 28 - Erase Cmd seq error */
#define RSP1_ERASE_SEQ_ERR_S 28
#define RSP1_BLK_LEN_ERR_M BITFIELD_MASK(1) /* Bit 29 - Block length error */
#define RSP1_BLK_LEN_ERR_S 29
#define RSP1_ADDR_ERR_M BITFIELD_MASK(1) /* Bit 30 - Misaligned address */
#define RSP1_ADDR_ERR_S 30
#define RSP1_OUT_OF_RANGE_M BITFIELD_MASK(1) /* Bit 31 - Cmd arg was out of range */
#define RSP1_OUT_OF_RANGE_S 31
#define RSP5_DATA_M BITFIELD_MASK(8) /* Bits [0:7] - data */
#define RSP5_DATA_S 0
#define RSP5_FLAGS_M BITFIELD_MASK(8) /* Bit [15:8] - Rsp flags */
#define RSP5_FLAGS_S 8
#define RSP5_STUFF_M BITFIELD_MASK(16) /* Bits [31:16] - Stuff bits */
#define RSP5_STUFF_S 16
/* ----------------------------------------------
* SDIO Command Response structures for SPI mode
* ----------------------------------------------
*/
#define SPIRSP4_IO_OCR_M BITFIELD_MASK(16) /* Bits [15:0] - Card's OCR Bits [23:8] */
#define SPIRSP4_IO_OCR_S 0
#define SPIRSP4_STUFF_M BITFIELD_MASK(3) /* Bits [18:16] - Stuff bits */
#define SPIRSP4_STUFF_S 16
#define SPIRSP4_MEM_PRESENT_M BITFIELD_MASK(1) /* Bit 19 - Memory present */
#define SPIRSP4_MEM_PRESENT_S 19
#define SPIRSP4_NUM_FUNCS_M BITFIELD_MASK(3) /* Bits [22:20] - Number of I/O funcs */
#define SPIRSP4_NUM_FUNCS_S 20
#define SPIRSP4_CARD_READY_M BITFIELD_MASK(1) /* Bit 23 - SDIO card ready */
#define SPIRSP4_CARD_READY_S 23
#define SPIRSP4_IDLE_STATE_M BITFIELD_MASK(1) /* Bit 24 - idle state */
#define SPIRSP4_IDLE_STATE_S 24
#define SPIRSP4_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 26 - Illegal Cmd error */
#define SPIRSP4_ILLEGAL_CMD_S 26
#define SPIRSP4_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 27 - COM CRC error */
#define SPIRSP4_COM_CRC_ERROR_S 27
#define SPIRSP4_FUNC_NUM_ERROR_M BITFIELD_MASK(1) /* Bit 28 - Function number error
*/
#define SPIRSP4_FUNC_NUM_ERROR_S 28
#define SPIRSP4_PARAM_ERROR_M BITFIELD_MASK(1) /* Bit 30 - Parameter Error Bit */
#define SPIRSP4_PARAM_ERROR_S 30
#define SPIRSP4_START_BIT_M BITFIELD_MASK(1) /* Bit 31 - Start Bit */
#define SPIRSP4_START_BIT_S 31
#define SPIRSP5_DATA_M BITFIELD_MASK(8) /* Bits [23:16] - R/W Data */
#define SPIRSP5_DATA_S 16
#define SPIRSP5_IDLE_STATE_M BITFIELD_MASK(1) /* Bit 24 - Idle state */
#define SPIRSP5_IDLE_STATE_S 24
#define SPIRSP5_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 26 - Illegal Cmd error */
#define SPIRSP5_ILLEGAL_CMD_S 26
#define SPIRSP5_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 27 - COM CRC error */
#define SPIRSP5_COM_CRC_ERROR_S 27
#define SPIRSP5_FUNC_NUM_ERROR_M BITFIELD_MASK(1) /* Bit 28 - Function number error
*/
#define SPIRSP5_FUNC_NUM_ERROR_S 28
#define SPIRSP5_PARAM_ERROR_M BITFIELD_MASK(1) /* Bit 30 - Parameter Error Bit */
#define SPIRSP5_PARAM_ERROR_S 30
#define SPIRSP5_START_BIT_M BITFIELD_MASK(1) /* Bit 31 - Start Bit */
#define SPIRSP5_START_BIT_S 31
/* RSP6 card status format; Pg 68 Physical Layer spec v 1.10 */
#define RSP6STAT_AKE_SEQ_ERROR_M BITFIELD_MASK(1) /* Bit 3 - Authentication seq error
*/
#define RSP6STAT_AKE_SEQ_ERROR_S 3
#define RSP6STAT_APP_CMD_M BITFIELD_MASK(1) /* Bit 5 - Card expects ACMD */
#define RSP6STAT_APP_CMD_S 5
#define RSP6STAT_READY_FOR_DATA_M BITFIELD_MASK(1) /* Bit 8 - Ready for data
* (buff empty)
*/
#define RSP6STAT_READY_FOR_DATA_S 8
#define RSP6STAT_CURR_STATE_M BITFIELD_MASK(4) /* Bits [12:9] - Card state at
* Cmd reception
*/
#define RSP6STAT_CURR_STATE_S 9
#define RSP6STAT_ERROR_M BITFIELD_MASK(1) /* Bit 13 - General/Unknown error Bit 19
*/
#define RSP6STAT_ERROR_S 13
#define RSP6STAT_ILLEGAL_CMD_M BITFIELD_MASK(1) /* Bit 14 - Illegal cmd for
* card state Bit 22
*/
#define RSP6STAT_ILLEGAL_CMD_S 14
#define RSP6STAT_COM_CRC_ERROR_M BITFIELD_MASK(1) /* Bit 15 - CRC previous command
* failed Bit 23
*/
#define RSP6STAT_COM_CRC_ERROR_S 15
#define SDIOH_XFER_TYPE_READ SD_IO_OP_READ
#define SDIOH_XFER_TYPE_WRITE SD_IO_OP_WRITE
#endif /* _SDIO_H */