blob: b8f37bb447a1f235db30b4540e63dfee7a637600 [file] [log] [blame]
 /* adler32.c -- compute the Adler-32 checksum of a data stream * Copyright (C) 1995-2004 Mark Adler * For conditions of distribution and use, see copyright notice in zlib.h */ /* @(#) \$Id\$ */ #define ZLIB_INTERNAL #include "zlib.h" #define BASE 65521UL /* largest prime smaller than 65536 */ #define NMAX 5552 /* NMAX is the largest n such that 255n(n+1)/2 + (n+1)(BASE-1) <= 2^32-1 */ #define DO1(buf,i) {adler += (buf)[i]; sum2 += adler;} #define DO2(buf,i) DO1(buf,i); DO1(buf,i+1); #define DO4(buf,i) DO2(buf,i); DO2(buf,i+2); #define DO8(buf,i) DO4(buf,i); DO4(buf,i+4); #define DO16(buf) DO8(buf,0); DO8(buf,8); /* use NO_DIVIDE if your processor does not do division in hardware */ #ifdef NO_DIVIDE # define MOD(a) \ do { \ if (a >= (BASE << 16)) a -= (BASE << 16); \ if (a >= (BASE << 15)) a -= (BASE << 15); \ if (a >= (BASE << 14)) a -= (BASE << 14); \ if (a >= (BASE << 13)) a -= (BASE << 13); \ if (a >= (BASE << 12)) a -= (BASE << 12); \ if (a >= (BASE << 11)) a -= (BASE << 11); \ if (a >= (BASE << 10)) a -= (BASE << 10); \ if (a >= (BASE << 9)) a -= (BASE << 9); \ if (a >= (BASE << 8)) a -= (BASE << 8); \ if (a >= (BASE << 7)) a -= (BASE << 7); \ if (a >= (BASE << 6)) a -= (BASE << 6); \ if (a >= (BASE << 5)) a -= (BASE << 5); \ if (a >= (BASE << 4)) a -= (BASE << 4); \ if (a >= (BASE << 3)) a -= (BASE << 3); \ if (a >= (BASE << 2)) a -= (BASE << 2); \ if (a >= (BASE << 1)) a -= (BASE << 1); \ if (a >= BASE) a -= BASE; \ } while (0) # define MOD4(a) \ do { \ if (a >= (BASE << 4)) a -= (BASE << 4); \ if (a >= (BASE << 3)) a -= (BASE << 3); \ if (a >= (BASE << 2)) a -= (BASE << 2); \ if (a >= (BASE << 1)) a -= (BASE << 1); \ if (a >= BASE) a -= BASE; \ } while (0) #else # define MOD(a) a %= BASE # define MOD4(a) a %= BASE #endif /* ========================================================================= */ /* The adler32 code below computes, in effect, uLong high = 0; uLong low = 1; for (j = 0; j < len; j++) { low = (low + buf[j]) % BASE; high = (high + low) % BASE; } checksum = (high << 16) | low; Both 16-bit halves of the checksum are between 0 and BASE-1 (inclusive). Hence, the minimum possible checksum value is 0, and the maximum is ((BASE-1) << 16) | (BASE-1). Applications may have reserved values outside this range to carry special meanings. NOTE: If adler32() is changed in ANY way, be absolutely sure that the change will NOT cause checksums previously stored to not match the data they were originally intended to match, or expand the range in such a way that values reserved by applications to carry special meanings now become checksums of valid data. Also, be sure to change adler32_range() accordingly. This explanation and adler32_range() are not part of original software distribution. They are added at Google (2006) in accordance with the copyright notice in zlib.h, which permits alteration and redistribution of the original software provided, among other things, that altered source versions must be plainly marked as such and not misrepresented as being the original software. */ void ZEXPORT adler32_range(min, max) uLong *min; uLong *max; { *min = 0L; *max = ((BASE-1) << 16) | (BASE-1); } uLong ZEXPORT adler32(adler, buf, len) uLong adler; const Bytef *buf; uInt len; { unsigned long sum2; unsigned n; /* split Adler-32 into component sums */ sum2 = (adler >> 16) & 0xffff; adler &= 0xffff; /* in case user likes doing a byte at a time, keep it fast */ if (len == 1) { adler += buf; if (adler >= BASE) adler -= BASE; sum2 += adler; if (sum2 >= BASE) sum2 -= BASE; return adler | (sum2 << 16); } /* initial Adler-32 value (deferred check for len == 1 speed) */ if (buf == Z_NULL) return 1L; /* in case short lengths are provided, keep it somewhat fast */ if (len < 16) { while (len--) { adler += *buf++; sum2 += adler; } if (adler >= BASE) adler -= BASE; MOD4(sum2); /* only added so many BASE's */ return adler | (sum2 << 16); } /* do length NMAX blocks -- requires just one modulo operation */ while (len >= NMAX) { len -= NMAX; n = NMAX / 16; /* NMAX is divisible by 16 */ do { DO16(buf); /* 16 sums unrolled */ buf += 16; } while (--n); MOD(adler); MOD(sum2); } /* do remaining bytes (less than NMAX, still just one modulo) */ if (len) { /* avoid modulos if none remaining */ while (len >= 16) { len -= 16; DO16(buf); buf += 16; } while (len--) { adler += *buf++; sum2 += adler; } MOD(adler); MOD(sum2); } /* return recombined sums */ return adler | (sum2 << 16); } /* ========================================================================= */ uLong ZEXPORT adler32_combine(adler1, adler2, len2) uLong adler1; uLong adler2; z_off_t len2; { unsigned long sum1; unsigned long sum2; unsigned rem; /* the derivation of this formula is left as an exercise for the reader */ rem = (unsigned)(len2 % BASE); sum1 = adler1 & 0xffff; sum2 = rem * sum1; MOD(sum2); sum1 += (adler2 & 0xffff) + BASE - 1; sum2 += ((adler1 >> 16) & 0xffff) + ((adler2 >> 16) & 0xffff) + BASE - rem; if (sum1 >= BASE) sum1 -= BASE; if (sum1 >= BASE) sum1 -= BASE; if (sum2 >= (BASE << 1)) sum2 -= (BASE << 1); if (sum2 >= BASE) sum2 -= BASE; return sum1 | (sum2 << 16); }