blob: 76208c4a405faf716f876c27340d6e3f666e840d [file] [log] [blame]
/******************************************************************************
*
* Copyright (C) 2011-2013 Broadcom Corporation
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at:
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*
******************************************************************************/
/******************************************************************************
*
* This file contains compile-time configurable constants for BRCM HAL
* modules
*
******************************************************************************/
#include "nfc_hal_int.h"
#include "nci_defs.h"
#include "nfc_brcm_defs.h"
/* the SetConfig at start up*/
UINT8 nfc_hal_start_up_cfg[] = {
/* TLV len */ 31,
/* B0 */ NCI_PARAM_ID_EMVCO_ENABLE,
/* B1 */ 1,
/* B2 */ 1, /* (1 = enable emvco mode, 0 = disable emvco mode) Default = 0.*/
/* B3 */ NCI_PARAM_ID_CONTINUE_MODE, /* NFCC will restart discovery after deactivated */
/* B4 */ 1,
/* B5 */ 1, /* (1 = enable, 0 = disable) Default = 0.*/
/* B6 */ NCI_PARAM_ID_RFU_CONFIG,
/* B7 */ 0x14,
/* B8 */ 0x00,
/* B9 */ 0x00,
/* B10*/ 0x00,
/* B11*/ 0x00,
/* B12*/ 0x0E,
/* B13*/ 0xE8,
/* B14*/ 0xF0,
/* B15*/ 0x55,
/* B16*/ 0x00,
/* B17*/ 0x0F, /* CE3 SO delay in sec */
/* B18*/ 0x00,
/* B19*/ 0x00,
/* B20*/ 0x00,
/* B21*/ 0x00,
/* B22*/ 0x00,
/* B23*/ 0x00,
/* B24*/ 0x00,
/* B25*/ 0x00,
/* B26*/ 0x00,
/* B27*/ 0x00,
/* B28*/ NCI_PARAM_ID_ACT_ORDER, /* polling sequence */
/* B29*/ 1,
/* B30*/ 1, /* (1 = active mode polling before passive, 0 = passive polling first) Default = 0.*/
};
UINT8 *p_nfc_hal_dm_start_up_cfg = (UINT8 *) nfc_hal_start_up_cfg;
/* the VSCs at start up:
* The VSCs are specified in TLV format similar to nfa_start_up_cfg[]
* first byte is the TLV total len.
* B0 is the first T; i.e. the opcode for the VSC
* B1 is the len of the VSC parameters/payload
* */
UINT8 nfc_hal_dm_start_up_vsc_cfg[] = {
/* TLV len */ 5,
/* B0 */ NCI_MTS_CMD|NCI_GID_PROP,
/* B1 */ NCI_MSG_FRAME_LOG,
/* B2 */ 2,
/* B3 */ 0, /* 1 to enable RF frames */
/* B4 */ 1 /* 1 to enable SWP frames */
};
UINT8 *p_nfc_hal_dm_start_up_vsc_cfg = NULL;
/* the SetConfig at HAL_NfcPreDiscover. This is done once after HAL_NfcOpen */
UINT8 nfc_hal_pre_discover_cfg[] = {
/* TLV len */ 0x0A,
/* B0 */ NCI_PARAM_ID_SWPCFG,
/* B1 */ 0x08,
/* B2 */ 0x01,
/* B3 */ 0x08,
/* B4 */ 0x00,
/* B5 */ 0x04,
/* B6 */ 0x80,
/* B7 */ 0xC3,
/* B8 */ 0xC9,
/* B9 */ 0x01
};
UINT8 *p_nfc_hal_pre_discover_cfg = NULL;
/* LPTD parameters (LowPowerTagDetection)
* This is typical values for 20791B2
* The timing and threshold parameters used for a customer handset/hardware may vary
* depending on antenna and should be verified during a customer testing phase.
* the data fields without comments are too complicated. Please see ""
* */
const UINT8 nfc_hal_dm_lptd_cfg[] =
{
21, /* total TLV length excluding itself */
NCI_PARAM_ID_TAGSNIFF_CFG, /* type */
19, /* length */
0x01, /* B0 enable: 0/disable, 1/enable*/
0x02, /* B1 poll count: number of full power poll before starting lptd poll */
0xFF, /* B2 sniff count lsb: number of lptd poll before switching to full power poll */
0xFF, /* B3 sniff count msb */
0x80, /* B4 threshold: Bigger thresholds give a smaller LPTD range but more immunity to false detections. Smaller thresholds increase LPTD range at the cost of greater likelihood of false detections. */
0x40, /* B5 delay lsb: delay (us) to sampling power */
0x00, /* B6 delay msb */
0x40, /* B7 carrier threshold lsb */
0x00, /* B8 carrier threshold msb */
0x80, /* B9 mode: Bitwise variable used to enable various algorithm modes.*/
0x80, /* B10 0-offset lsb */
0x00, /* B11 0-offset msb */
0x10, /* B12 field sense time lsb */
0x00, /* B13 field sense time msb */
0x00, /* B14 false detect threshold lsb: 0x00 to disable LPTD NTF. The number of false tag detections to resport LPTD NTF. */
0x00, /* B15 false detect threshold msb. A false tag detect - full poll results in no tag being detected.*/
0x75, /* B16 mode1; Bitwise variable used to enable various algorithm modes. */
0x0D, /* B17 lptd ant cfg rx */
0x30, /* B18 lptd rdr cfg ve */
};
UINT8 *p_nfc_hal_dm_lptd_cfg = (UINT8 *) &nfc_hal_dm_lptd_cfg[0];
/*
** NFCC has a table which has 9 XTAL frequencies: 9.6, 13, 16.2, 19.2, 24, 26, 38.4, 52 and 37.4 in MHz.
** For these 9 xtal frequencies, host doesn't need to configure PLL325.
** For 43341, host doesn't need to configure it at all.
*/
UINT8 *p_nfc_hal_dm_pll_325_cfg = NULL;
tNFC_HAL_CFG nfc_hal_cfg =
{
FALSE, /* set nfc_hal_prm_nvm_required to TRUE, if the platform wants to abort PRM process without NVM */
(UINT16) NFC_HAL_NFCC_ENABLE_TIMEOUT, /* max time to wait for RESET NTF after setting REG_PU to high
** If NFCC doesn't have NVM or cannot load patch from NVM without Xtal setting
** then set it to short to optimize bootup time because NFCC cannot send RESET NTF.
** Otherwise, it depends on NVM type and size of patchram.
*/
(UINT16) NFC_HAL_NFCC_ENABLE_TIMEOUT, /* max time to wait for RESET NTF after setting Xtal frequency
** It depends on NVM type and size of patchram.
*/
(HAL_NFC_HCI_UICC0_HOST | HAL_NFC_HCI_UICC1_HOST) /* Set bit(s) for supported UICC(s) */
};
tNFC_HAL_CFG *p_nfc_hal_cfg= (tNFC_HAL_CFG *) &nfc_hal_cfg;