|author||android-build-team Robot <email@example.com>||Mon Nov 11 21:35:00 2019 +0000|
|committer||android-build-team Robot <firstname.lastname@example.org>||Mon Nov 11 21:35:00 2019 +0000|
Snap for 6001391 from 80415b0f402f3b87f477c2048cdc4aca04bfcf74 to qt-aml-networking-release Change-Id: I61dbba129aa8296faec5ac322d8f4a6cae21ee36
Devices using recovery-as-boot (e.g. Pixels, which set BOARD_USES_RECOVERY_AS_BOOT)
# After setting up environment and lunch. m -j bootimage adb reboot bootloader # Pixel devices don't support booting into recovery mode with `fastboot boot`. fastboot flash boot # Manually choose `Recovery mode` from bootloader menu.
Devices with a separate recovery image (e.g. Nexus)
# After setting up environment and lunch. mm -j && m ramdisk-nodeps && m recoveryimage-nodeps adb reboot bootloader # To boot into the new recovery image without flashing the recovery partition: fastboot boot $ANDROID_PRODUCT_OUT/recovery.img
# After setting up environment and lunch. mmma -j bootable/recovery # Running the tests on device (under normal boot). adb root adb sync data # 32-bit device adb shell /data/nativetest/recovery_unit_test/recovery_unit_test # Or 64-bit device adb shell /data/nativetest64/recovery_unit_test/recovery_unit_test
recovery-persist executables exist only on systems without /cache partition. And we need to follow special steps to run tests for them.
Execute the test on an A/B device first. The test should fail but it will log some contents to pmsg.
Reboot the device immediately and run the test again. The test should save the contents of pmsg buffer into /data/misc/recovery/inject.txt. Test will pass if this file has expected contents.
When running recovery image from debuggable builds (i.e.
-userdebug build variants, or
adbd service is enabled and started by default, which allows
adb communication. A device should be listed under
adb devices, either in
$ adb devices List of devices attached 1234567890abcdef recovery
/system/bin/adbd is built from the same code base as the one in the normal boot, only a subset of
adb commands are meaningful under recovery, such as
adb pull etc. Since Android Q,
adb shell no longer requires manually mounting
/system from recovery menu.
$ adb devices List of devices attached
adbdis built and running.
adbd is always included into recovery image, as
adbd service automatically only in debuggable builds. This behavior is controlled by the recovery specific
/init.rc, whose source code is at
The best way to confirm a running
adbd is by checking the serial output, which shows a service start log as below.
[ 18.961986] c1 1 init: starting service 'adbd'...
adbd service has been started but device not shown under
adb devices, use
lsusb(8) (on host) to check if the device is visible to the host.
bootable/recovery/etc/init.rc disables Android USB gadget (via sysfs) as part of the
fs action trigger, and will only re-enable it in debuggable builds (the
on property rule will always run after
on fs write /sys/class/android_usb/android0/enable 0 # Always start adbd on userdebug and eng builds on property:ro.debuggable=1 write /sys/class/android_usb/android0/enable 1 start adbd
If device is using configfs, check if configfs has been properly set up in init rc scripts. See the example configuration for Pixel 2 devices. Note that the flag set via sysfs (i.e. the one above) is no-op when using configfs.
$ adb devices List of devices attached 1234567890abcdef unauthorized
recovery image doesn‘t honor the USB debugging toggle and the authorizations added under normal boot (because such authorization data stays in /data, which recovery doesn’t mount), nor does it support authorizing a host device under recovery. We can use one of the following options instead.
For debuggable builds, an RSA keypair can be used to authorize a host device that has the private key. The public key, defined via
PRODUCT_ADB_KEYS, will be copied to
/adb_keys. When starting the host-side
adbd, make sure the filename (or the directory) of the matching private key has been added to
$ export ADB_VENDOR_KEYS=/path/to/adb/private/key $ adb kill-server $ adb devices
-user builds filter out
PRODUCT_ADB_KEYS, so no
/adb_keys will be included there.
Note that this mechanism applies to both of normal boot and recovery modes.
adbdto connect without authentication.
adbdis compiled with
ALLOW_ADBD_NO_AUTH(only on debuggable builds).
ro.adb.securehas a value of
Both of the two conditions need to be satisfied. Although
ro.adb.secure is a runtime property, its value is set at build time (written into
/prop.default). It defaults to
-user builds, and
0 for other build variants. The value is overridable via