blob: 7cd87d24a7a0f26cb5e211c45911d270bc03e4e0 [file] [log] [blame]
/*
* This file contains code to reset and initialize USB host controllers.
* Some of it includes work-arounds for PCI hardware and BIOS quirks.
* It may need to run early during booting -- before USB would normally
* initialize -- to ensure that Linux doesn't use any legacy modes.
*
* Copyright (c) 1999 Martin Mares <mj@ucw.cz>
* (and others)
*/
#include <linux/types.h>
#include <linux/kconfig.h>
#include <linux/kernel.h>
#include <linux/pci.h>
#include <linux/init.h>
#include <linux/delay.h>
#include <linux/export.h>
#include <linux/acpi.h>
#include <linux/dmi.h>
#include "pci-quirks.h"
#include "xhci.h"
#define UHCI_USBLEGSUP 0xc0 /* legacy support */
#define UHCI_USBCMD 0 /* command register */
#define UHCI_USBINTR 4 /* interrupt register */
#define UHCI_USBLEGSUP_RWC 0x8f00 /* the R/WC bits */
#define UHCI_USBLEGSUP_RO 0x5040 /* R/O and reserved bits */
#define UHCI_USBCMD_RUN 0x0001 /* RUN/STOP bit */
#define UHCI_USBCMD_HCRESET 0x0002 /* Host Controller reset */
#define UHCI_USBCMD_EGSM 0x0008 /* Global Suspend Mode */
#define UHCI_USBCMD_CONFIGURE 0x0040 /* Config Flag */
#define UHCI_USBINTR_RESUME 0x0002 /* Resume interrupt enable */
#define OHCI_CONTROL 0x04
#define OHCI_CMDSTATUS 0x08
#define OHCI_INTRSTATUS 0x0c
#define OHCI_INTRENABLE 0x10
#define OHCI_INTRDISABLE 0x14
#define OHCI_FMINTERVAL 0x34
#define OHCI_HCFS (3 << 6) /* hc functional state */
#define OHCI_HCR (1 << 0) /* host controller reset */
#define OHCI_OCR (1 << 3) /* ownership change request */
#define OHCI_CTRL_RWC (1 << 9) /* remote wakeup connected */
#define OHCI_CTRL_IR (1 << 8) /* interrupt routing */
#define OHCI_INTR_OC (1 << 30) /* ownership change */
#define EHCI_HCC_PARAMS 0x08 /* extended capabilities */
#define EHCI_USBCMD 0 /* command register */
#define EHCI_USBCMD_RUN (1 << 0) /* RUN/STOP bit */
#define EHCI_USBSTS 4 /* status register */
#define EHCI_USBSTS_HALTED (1 << 12) /* HCHalted bit */
#define EHCI_USBINTR 8 /* interrupt register */
#define EHCI_CONFIGFLAG 0x40 /* configured flag register */
#define EHCI_USBLEGSUP 0 /* legacy support register */
#define EHCI_USBLEGSUP_BIOS (1 << 16) /* BIOS semaphore */
#define EHCI_USBLEGSUP_OS (1 << 24) /* OS semaphore */
#define EHCI_USBLEGCTLSTS 4 /* legacy control/status */
#define EHCI_USBLEGCTLSTS_SOOE (1 << 13) /* SMI on ownership change */
/* AMD quirk use */
#define AB_REG_BAR_LOW 0xe0
#define AB_REG_BAR_HIGH 0xe1
#define AB_REG_BAR_SB700 0xf0
#define AB_INDX(addr) ((addr) + 0x00)
#define AB_DATA(addr) ((addr) + 0x04)
#define AX_INDXC 0x30
#define AX_DATAC 0x34
#define NB_PCIE_INDX_ADDR 0xe0
#define NB_PCIE_INDX_DATA 0xe4
#define PCIE_P_CNTL 0x10040
#define BIF_NB 0x10002
#define NB_PIF0_PWRDOWN_0 0x01100012
#define NB_PIF0_PWRDOWN_1 0x01100013
#define USB_INTEL_XUSB2PR 0xD0
#define USB_INTEL_USB2PRM 0xD4
#define USB_INTEL_USB3_PSSEN 0xD8
#define USB_INTEL_USB3PRM 0xDC
static struct amd_chipset_info {
struct pci_dev *nb_dev;
struct pci_dev *smbus_dev;
int nb_type;
int sb_type;
int isoc_reqs;
int probe_count;
int probe_result;
} amd_chipset;
static DEFINE_SPINLOCK(amd_lock);
int usb_amd_find_chipset_info(void)
{
u8 rev = 0;
unsigned long flags;
struct amd_chipset_info info;
int ret;
spin_lock_irqsave(&amd_lock, flags);
/* probe only once */
if (amd_chipset.probe_count > 0) {
amd_chipset.probe_count++;
spin_unlock_irqrestore(&amd_lock, flags);
return amd_chipset.probe_result;
}
memset(&info, 0, sizeof(info));
spin_unlock_irqrestore(&amd_lock, flags);
info.smbus_dev = pci_get_device(PCI_VENDOR_ID_ATI, 0x4385, NULL);
if (info.smbus_dev) {
rev = info.smbus_dev->revision;
if (rev >= 0x40)
info.sb_type = 1;
else if (rev >= 0x30 && rev <= 0x3b)
info.sb_type = 3;
} else {
info.smbus_dev = pci_get_device(PCI_VENDOR_ID_AMD,
0x780b, NULL);
if (!info.smbus_dev) {
ret = 0;
goto commit;
}
rev = info.smbus_dev->revision;
if (rev >= 0x11 && rev <= 0x18)
info.sb_type = 2;
}
if (info.sb_type == 0) {
if (info.smbus_dev) {
pci_dev_put(info.smbus_dev);
info.smbus_dev = NULL;
}
ret = 0;
goto commit;
}
info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x9601, NULL);
if (info.nb_dev) {
info.nb_type = 1;
} else {
info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD, 0x1510, NULL);
if (info.nb_dev) {
info.nb_type = 2;
} else {
info.nb_dev = pci_get_device(PCI_VENDOR_ID_AMD,
0x9600, NULL);
if (info.nb_dev)
info.nb_type = 3;
}
}
ret = info.probe_result = 1;
printk(KERN_DEBUG "QUIRK: Enable AMD PLL fix\n");
commit:
spin_lock_irqsave(&amd_lock, flags);
if (amd_chipset.probe_count > 0) {
/* race - someone else was faster - drop devices */
/* Mark that we where here */
amd_chipset.probe_count++;
ret = amd_chipset.probe_result;
spin_unlock_irqrestore(&amd_lock, flags);
if (info.nb_dev)
pci_dev_put(info.nb_dev);
if (info.smbus_dev)
pci_dev_put(info.smbus_dev);
} else {
/* no race - commit the result */
info.probe_count++;
amd_chipset = info;
spin_unlock_irqrestore(&amd_lock, flags);
}
return ret;
}
EXPORT_SYMBOL_GPL(usb_amd_find_chipset_info);
/*
* The hardware normally enables the A-link power management feature, which
* lets the system lower the power consumption in idle states.
*
* This USB quirk prevents the link going into that lower power state
* during isochronous transfers.
*
* Without this quirk, isochronous stream on OHCI/EHCI/xHCI controllers of
* some AMD platforms may stutter or have breaks occasionally.
*/
static void usb_amd_quirk_pll(int disable)
{
u32 addr, addr_low, addr_high, val;
u32 bit = disable ? 0 : 1;
unsigned long flags;
spin_lock_irqsave(&amd_lock, flags);
if (disable) {
amd_chipset.isoc_reqs++;
if (amd_chipset.isoc_reqs > 1) {
spin_unlock_irqrestore(&amd_lock, flags);
return;
}
} else {
amd_chipset.isoc_reqs--;
if (amd_chipset.isoc_reqs > 0) {
spin_unlock_irqrestore(&amd_lock, flags);
return;
}
}
if (amd_chipset.sb_type == 1 || amd_chipset.sb_type == 2) {
outb_p(AB_REG_BAR_LOW, 0xcd6);
addr_low = inb_p(0xcd7);
outb_p(AB_REG_BAR_HIGH, 0xcd6);
addr_high = inb_p(0xcd7);
addr = addr_high << 8 | addr_low;
outl_p(0x30, AB_INDX(addr));
outl_p(0x40, AB_DATA(addr));
outl_p(0x34, AB_INDX(addr));
val = inl_p(AB_DATA(addr));
} else if (amd_chipset.sb_type == 3) {
pci_read_config_dword(amd_chipset.smbus_dev,
AB_REG_BAR_SB700, &addr);
outl(AX_INDXC, AB_INDX(addr));
outl(0x40, AB_DATA(addr));
outl(AX_DATAC, AB_INDX(addr));
val = inl(AB_DATA(addr));
} else {
spin_unlock_irqrestore(&amd_lock, flags);
return;
}
if (disable) {
val &= ~0x08;
val |= (1 << 4) | (1 << 9);
} else {
val |= 0x08;
val &= ~((1 << 4) | (1 << 9));
}
outl_p(val, AB_DATA(addr));
if (!amd_chipset.nb_dev) {
spin_unlock_irqrestore(&amd_lock, flags);
return;
}
if (amd_chipset.nb_type == 1 || amd_chipset.nb_type == 3) {
addr = PCIE_P_CNTL;
pci_write_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_ADDR, addr);
pci_read_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_DATA, &val);
val &= ~(1 | (1 << 3) | (1 << 4) | (1 << 9) | (1 << 12));
val |= bit | (bit << 3) | (bit << 12);
val |= ((!bit) << 4) | ((!bit) << 9);
pci_write_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_DATA, val);
addr = BIF_NB;
pci_write_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_ADDR, addr);
pci_read_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_DATA, &val);
val &= ~(1 << 8);
val |= bit << 8;
pci_write_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_DATA, val);
} else if (amd_chipset.nb_type == 2) {
addr = NB_PIF0_PWRDOWN_0;
pci_write_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_ADDR, addr);
pci_read_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_DATA, &val);
if (disable)
val &= ~(0x3f << 7);
else
val |= 0x3f << 7;
pci_write_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_DATA, val);
addr = NB_PIF0_PWRDOWN_1;
pci_write_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_ADDR, addr);
pci_read_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_DATA, &val);
if (disable)
val &= ~(0x3f << 7);
else
val |= 0x3f << 7;
pci_write_config_dword(amd_chipset.nb_dev,
NB_PCIE_INDX_DATA, val);
}
spin_unlock_irqrestore(&amd_lock, flags);
return;
}
void usb_amd_quirk_pll_disable(void)
{
usb_amd_quirk_pll(1);
}
EXPORT_SYMBOL_GPL(usb_amd_quirk_pll_disable);
/* usb_quirk_ignore_comp_plc - If ignore PLC event for
* compliance/loopback mode transition.
* @ptr: base address of PORTSC egisters to be read.
* @ports: number of ports.
*
* Some xHC controller will generate PLC event when link transfer to
* compliance/loopback mode. By design, driver will trigger warm reset
* for this case which will interrupt USB3 electronic compliance test.
* So if want to avoid it, need to set XHCI_COMP_PLC_QUIRK during driver
* initialization.
**/
int usb_quirk_ignore_comp_plc(void __iomem *ptr, int ports)
{
int i;
u32 val;
__le32 __iomem *addr;
addr = ptr;
for (i = 0; i < ports; i++) {
val = readl(addr);
if (((val & PORT_PLC) && (val & PORT_PLS_MASK) == XDEV_COMP) ||
((val & PORT_PLC) && (val & PORT_PLS_MASK) == XDEV_LOOPBACK))
return 1;
addr += NUM_PORT_REGS;
}
return 0;
}
EXPORT_SYMBOL_GPL(usb_quirk_ignore_comp_plc);
void usb_amd_quirk_pll_enable(void)
{
usb_amd_quirk_pll(0);
}
EXPORT_SYMBOL_GPL(usb_amd_quirk_pll_enable);
void usb_amd_dev_put(void)
{
struct pci_dev *nb, *smbus;
unsigned long flags;
spin_lock_irqsave(&amd_lock, flags);
amd_chipset.probe_count--;
if (amd_chipset.probe_count > 0) {
spin_unlock_irqrestore(&amd_lock, flags);
return;
}
/* save them to pci_dev_put outside of spinlock */
nb = amd_chipset.nb_dev;
smbus = amd_chipset.smbus_dev;
amd_chipset.nb_dev = NULL;
amd_chipset.smbus_dev = NULL;
amd_chipset.nb_type = 0;
amd_chipset.sb_type = 0;
amd_chipset.isoc_reqs = 0;
amd_chipset.probe_result = 0;
spin_unlock_irqrestore(&amd_lock, flags);
if (nb)
pci_dev_put(nb);
if (smbus)
pci_dev_put(smbus);
}
EXPORT_SYMBOL_GPL(usb_amd_dev_put);
/*
* Make sure the controller is completely inactive, unable to
* generate interrupts or do DMA.
*/
void uhci_reset_hc(struct pci_dev *pdev, unsigned long base)
{
/* Turn off PIRQ enable and SMI enable. (This also turns off the
* BIOS's USB Legacy Support.) Turn off all the R/WC bits too.
*/
pci_write_config_word(pdev, UHCI_USBLEGSUP, UHCI_USBLEGSUP_RWC);
/* Reset the HC - this will force us to get a
* new notification of any already connected
* ports due to the virtual disconnect that it
* implies.
*/
outw(UHCI_USBCMD_HCRESET, base + UHCI_USBCMD);
mb();
udelay(5);
if (inw(base + UHCI_USBCMD) & UHCI_USBCMD_HCRESET)
dev_warn(&pdev->dev, "HCRESET not completed yet!\n");
/* Just to be safe, disable interrupt requests and
* make sure the controller is stopped.
*/
outw(0, base + UHCI_USBINTR);
outw(0, base + UHCI_USBCMD);
}
EXPORT_SYMBOL_GPL(uhci_reset_hc);
/*
* Initialize a controller that was newly discovered or has just been
* resumed. In either case we can't be sure of its previous state.
*
* Returns: 1 if the controller was reset, 0 otherwise.
*/
int uhci_check_and_reset_hc(struct pci_dev *pdev, unsigned long base)
{
u16 legsup;
unsigned int cmd, intr;
/*
* When restarting a suspended controller, we expect all the
* settings to be the same as we left them:
*
* PIRQ and SMI disabled, no R/W bits set in USBLEGSUP;
* Controller is stopped and configured with EGSM set;
* No interrupts enabled except possibly Resume Detect.
*
* If any of these conditions are violated we do a complete reset.
*/
pci_read_config_word(pdev, UHCI_USBLEGSUP, &legsup);
if (legsup & ~(UHCI_USBLEGSUP_RO | UHCI_USBLEGSUP_RWC)) {
dev_dbg(&pdev->dev, "%s: legsup = 0x%04x\n",
__func__, legsup);
goto reset_needed;
}
cmd = inw(base + UHCI_USBCMD);
if ((cmd & UHCI_USBCMD_RUN) || !(cmd & UHCI_USBCMD_CONFIGURE) ||
!(cmd & UHCI_USBCMD_EGSM)) {
dev_dbg(&pdev->dev, "%s: cmd = 0x%04x\n",
__func__, cmd);
goto reset_needed;
}
intr = inw(base + UHCI_USBINTR);
if (intr & (~UHCI_USBINTR_RESUME)) {
dev_dbg(&pdev->dev, "%s: intr = 0x%04x\n",
__func__, intr);
goto reset_needed;
}
return 0;
reset_needed:
dev_dbg(&pdev->dev, "Performing full reset\n");
uhci_reset_hc(pdev, base);
return 1;
}
EXPORT_SYMBOL_GPL(uhci_check_and_reset_hc);
static inline int io_type_enabled(struct pci_dev *pdev, unsigned int mask)
{
u16 cmd;
return !pci_read_config_word(pdev, PCI_COMMAND, &cmd) && (cmd & mask);
}
#define pio_enabled(dev) io_type_enabled(dev, PCI_COMMAND_IO)
#define mmio_enabled(dev) io_type_enabled(dev, PCI_COMMAND_MEMORY)
static void quirk_usb_handoff_uhci(struct pci_dev *pdev)
{
unsigned long base = 0;
int i;
if (!pio_enabled(pdev))
return;
for (i = 0; i < PCI_ROM_RESOURCE; i++)
if ((pci_resource_flags(pdev, i) & IORESOURCE_IO)) {
base = pci_resource_start(pdev, i);
break;
}
if (base)
uhci_check_and_reset_hc(pdev, base);
}
static int mmio_resource_enabled(struct pci_dev *pdev, int idx)
{
return pci_resource_start(pdev, idx) && mmio_enabled(pdev);
}
static void quirk_usb_handoff_ohci(struct pci_dev *pdev)
{
void __iomem *base;
u32 control;
u32 fminterval = 0;
bool no_fminterval = false;
int cnt;
if (!mmio_resource_enabled(pdev, 0))
return;
base = pci_ioremap_bar(pdev, 0);
if (base == NULL)
return;
/*
* ULi M5237 OHCI controller locks the whole system when accessing
* the OHCI_FMINTERVAL offset.
*/
if (pdev->vendor == PCI_VENDOR_ID_AL && pdev->device == 0x5237)
no_fminterval = true;
control = readl(base + OHCI_CONTROL);
/* On PA-RISC, PDC can leave IR set incorrectly; ignore it there. */
#ifdef __hppa__
#define OHCI_CTRL_MASK (OHCI_CTRL_RWC | OHCI_CTRL_IR)
#else
#define OHCI_CTRL_MASK OHCI_CTRL_RWC
if (control & OHCI_CTRL_IR) {
int wait_time = 500; /* arbitrary; 5 seconds */
writel(OHCI_INTR_OC, base + OHCI_INTRENABLE);
writel(OHCI_OCR, base + OHCI_CMDSTATUS);
while (wait_time > 0 &&
readl(base + OHCI_CONTROL) & OHCI_CTRL_IR) {
wait_time -= 10;
msleep(10);
}
if (wait_time <= 0)
dev_warn(&pdev->dev, "OHCI: BIOS handoff failed"
" (BIOS bug?) %08x\n",
readl(base + OHCI_CONTROL));
}
#endif
/* disable interrupts */
writel((u32) ~0, base + OHCI_INTRDISABLE);
/* Reset the USB bus, if the controller isn't already in RESET */
if (control & OHCI_HCFS) {
/* Go into RESET, preserving RWC (and possibly IR) */
writel(control & OHCI_CTRL_MASK, base + OHCI_CONTROL);
readl(base + OHCI_CONTROL);
/* drive bus reset for at least 50 ms (7.1.7.5) */
msleep(50);
}
/* software reset of the controller, preserving HcFmInterval */
if (!no_fminterval)
fminterval = readl(base + OHCI_FMINTERVAL);
writel(OHCI_HCR, base + OHCI_CMDSTATUS);
/* reset requires max 10 us delay */
for (cnt = 30; cnt > 0; --cnt) { /* ... allow extra time */
if ((readl(base + OHCI_CMDSTATUS) & OHCI_HCR) == 0)
break;
udelay(1);
}
if (!no_fminterval)
writel(fminterval, base + OHCI_FMINTERVAL);
/* Now the controller is safely in SUSPEND and nothing can wake it up */
iounmap(base);
}
static const struct dmi_system_id ehci_dmi_nohandoff_table[] = {
{
/* Pegatron Lucid (ExoPC) */
.matches = {
DMI_MATCH(DMI_BOARD_NAME, "EXOPG06411"),
DMI_MATCH(DMI_BIOS_VERSION, "Lucid-CE-133"),
},
},
{
/* Pegatron Lucid (Ordissimo AIRIS) */
.matches = {
DMI_MATCH(DMI_BOARD_NAME, "M11JB"),
DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
},
},
{
/* Pegatron Lucid (Ordissimo) */
.matches = {
DMI_MATCH(DMI_BOARD_NAME, "Ordissimo"),
DMI_MATCH(DMI_BIOS_VERSION, "Lucid-"),
},
},
{
/* HASEE E200 */
.matches = {
DMI_MATCH(DMI_BOARD_VENDOR, "HASEE"),
DMI_MATCH(DMI_BOARD_NAME, "E210"),
DMI_MATCH(DMI_BIOS_VERSION, "6.00"),
},
},
{ }
};
static void ehci_bios_handoff(struct pci_dev *pdev,
void __iomem *op_reg_base,
u32 cap, u8 offset)
{
int try_handoff = 1, tried_handoff = 0;
/*
* The Pegatron Lucid tablet sporadically waits for 98 seconds trying
* the handoff on its unused controller. Skip it.
*
* The HASEE E200 hangs when the semaphore is set (bugzilla #77021).
*/
if (pdev->vendor == 0x8086 && (pdev->device == 0x283a ||
pdev->device == 0x27cc)) {
if (dmi_check_system(ehci_dmi_nohandoff_table))
try_handoff = 0;
}
if (try_handoff && (cap & EHCI_USBLEGSUP_BIOS)) {
dev_dbg(&pdev->dev, "EHCI: BIOS handoff\n");
#if 0
/* aleksey_gorelov@phoenix.com reports that some systems need SMI forced on,
* but that seems dubious in general (the BIOS left it off intentionally)
* and is known to prevent some systems from booting. so we won't do this
* unless maybe we can determine when we're on a system that needs SMI forced.
*/
/* BIOS workaround (?): be sure the pre-Linux code
* receives the SMI
*/
pci_read_config_dword(pdev, offset + EHCI_USBLEGCTLSTS, &val);
pci_write_config_dword(pdev, offset + EHCI_USBLEGCTLSTS,
val | EHCI_USBLEGCTLSTS_SOOE);
#endif
/* some systems get upset if this semaphore is
* set for any other reason than forcing a BIOS
* handoff..
*/
pci_write_config_byte(pdev, offset + 3, 1);
}
/* if boot firmware now owns EHCI, spin till it hands it over. */
if (try_handoff) {
int msec = 1000;
while ((cap & EHCI_USBLEGSUP_BIOS) && (msec > 0)) {
tried_handoff = 1;
msleep(10);
msec -= 10;
pci_read_config_dword(pdev, offset, &cap);
}
}
if (cap & EHCI_USBLEGSUP_BIOS) {
/* well, possibly buggy BIOS... try to shut it down,
* and hope nothing goes too wrong
*/
if (try_handoff)
dev_warn(&pdev->dev, "EHCI: BIOS handoff failed"
" (BIOS bug?) %08x\n", cap);
pci_write_config_byte(pdev, offset + 2, 0);
}
/* just in case, always disable EHCI SMIs */
pci_write_config_dword(pdev, offset + EHCI_USBLEGCTLSTS, 0);
/* If the BIOS ever owned the controller then we can't expect
* any power sessions to remain intact.
*/
if (tried_handoff)
writel(0, op_reg_base + EHCI_CONFIGFLAG);
}
static void quirk_usb_disable_ehci(struct pci_dev *pdev)
{
void __iomem *base, *op_reg_base;
u32 hcc_params, cap, val;
u8 offset, cap_length;
int wait_time, count = 256/4;
if (!mmio_resource_enabled(pdev, 0))
return;
base = pci_ioremap_bar(pdev, 0);
if (base == NULL)
return;
cap_length = readb(base);
op_reg_base = base + cap_length;
/* EHCI 0.96 and later may have "extended capabilities"
* spec section 5.1 explains the bios handoff, e.g. for
* booting from USB disk or using a usb keyboard
*/
hcc_params = readl(base + EHCI_HCC_PARAMS);
offset = (hcc_params >> 8) & 0xff;
while (offset && --count) {
pci_read_config_dword(pdev, offset, &cap);
switch (cap & 0xff) {
case 1:
ehci_bios_handoff(pdev, op_reg_base, cap, offset);
break;
case 0: /* Illegal reserved cap, set cap=0 so we exit */
cap = 0; /* then fallthrough... */
default:
dev_warn(&pdev->dev, "EHCI: unrecognized capability "
"%02x\n", cap & 0xff);
}
offset = (cap >> 8) & 0xff;
}
if (!count)
dev_printk(KERN_DEBUG, &pdev->dev, "EHCI: capability loop?\n");
/*
* halt EHCI & disable its interrupts in any case
*/
val = readl(op_reg_base + EHCI_USBSTS);
if ((val & EHCI_USBSTS_HALTED) == 0) {
val = readl(op_reg_base + EHCI_USBCMD);
val &= ~EHCI_USBCMD_RUN;
writel(val, op_reg_base + EHCI_USBCMD);
wait_time = 2000;
do {
writel(0x3f, op_reg_base + EHCI_USBSTS);
udelay(100);
wait_time -= 100;
val = readl(op_reg_base + EHCI_USBSTS);
if ((val == ~(u32)0) || (val & EHCI_USBSTS_HALTED)) {
break;
}
} while (wait_time > 0);
}
writel(0, op_reg_base + EHCI_USBINTR);
writel(0x3f, op_reg_base + EHCI_USBSTS);
iounmap(base);
}
/*
* handshake - spin reading a register until handshake completes
* @ptr: address of hc register to be read
* @mask: bits to look at in result of read
* @done: value of those bits when handshake succeeds
* @wait_usec: timeout in microseconds
* @delay_usec: delay in microseconds to wait between polling
*
* Polls a register every delay_usec microseconds.
* Returns 0 when the mask bits have the value done.
* Returns -ETIMEDOUT if this condition is not true after
* wait_usec microseconds have passed.
*/
static int handshake(void __iomem *ptr, u32 mask, u32 done,
int wait_usec, int delay_usec)
{
u32 result;
do {
result = readl(ptr);
result &= mask;
if (result == done)
return 0;
udelay(delay_usec);
wait_usec -= delay_usec;
} while (wait_usec > 0);
return -ETIMEDOUT;
}
#define PCI_DEVICE_ID_INTEL_LYNX_POINT_XHCI 0x8C31
#define PCI_DEVICE_ID_INTEL_LYNX_POINT_LP_XHCI 0x9C31
bool usb_is_intel_ppt_switchable_xhci(struct pci_dev *pdev)
{
return pdev->class == PCI_CLASS_SERIAL_USB_XHCI &&
pdev->vendor == PCI_VENDOR_ID_INTEL &&
pdev->device == PCI_DEVICE_ID_INTEL_PANTHERPOINT_XHCI;
}
/* The Intel Lynx Point chipset also has switchable ports. */
bool usb_is_intel_lpt_switchable_xhci(struct pci_dev *pdev)
{
return pdev->class == PCI_CLASS_SERIAL_USB_XHCI &&
pdev->vendor == PCI_VENDOR_ID_INTEL &&
(pdev->device == PCI_DEVICE_ID_INTEL_LYNX_POINT_XHCI ||
pdev->device == PCI_DEVICE_ID_INTEL_LYNX_POINT_LP_XHCI);
}
bool usb_is_intel_switchable_xhci(struct pci_dev *pdev)
{
return usb_is_intel_ppt_switchable_xhci(pdev) ||
usb_is_intel_lpt_switchable_xhci(pdev);
}
EXPORT_SYMBOL_GPL(usb_is_intel_switchable_xhci);
/*
* Intel's Panther Point chipset has two host controllers (EHCI and xHCI) that
* share some number of ports. These ports can be switched between either
* controller. Not all of the ports under the EHCI host controller may be
* switchable.
*
* The ports should be switched over to xHCI before PCI probes for any device
* start. This avoids active devices under EHCI being disconnected during the
* port switchover, which could cause loss of data on USB storage devices, or
* failed boot when the root file system is on a USB mass storage device and is
* enumerated under EHCI first.
*
* We write into the xHC's PCI configuration space in some Intel-specific
* registers to switch the ports over. The USB 3.0 terminations and the USB
* 2.0 data wires are switched separately. We want to enable the SuperSpeed
* terminations before switching the USB 2.0 wires over, so that USB 3.0
* devices connect at SuperSpeed, rather than at USB 2.0 speeds.
*/
void usb_enable_xhci_ports(struct pci_dev *xhci_pdev)
{
u32 ports_available;
/* Don't switchover the ports if the user hasn't compiled the xHCI
* driver. Otherwise they will see "dead" USB ports that don't power
* the devices.
*/
if (!IS_ENABLED(CONFIG_USB_XHCI_HCD)) {
dev_warn(&xhci_pdev->dev,
"CONFIG_USB_XHCI_HCD is turned off, "
"defaulting to EHCI.\n");
dev_warn(&xhci_pdev->dev,
"USB 3.0 devices will work at USB 2.0 speeds.\n");
usb_disable_xhci_ports(xhci_pdev);
return;
}
/* Read USB3PRM, the USB 3.0 Port Routing Mask Register
* Indicate the ports that can be changed from OS.
*/
pci_read_config_dword(xhci_pdev, USB_INTEL_USB3PRM,
&ports_available);
dev_dbg(&xhci_pdev->dev, "Configurable ports to enable SuperSpeed: 0x%x\n",
ports_available);
/* Write USB3_PSSEN, the USB 3.0 Port SuperSpeed Enable
* Register, to turn on SuperSpeed terminations for the
* switchable ports.
*/
pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
cpu_to_le32(ports_available));
pci_read_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN,
&ports_available);
dev_dbg(&xhci_pdev->dev, "USB 3.0 ports that are now enabled "
"under xHCI: 0x%x\n", ports_available);
/* Read XUSB2PRM, xHCI USB 2.0 Port Routing Mask Register
* Indicate the USB 2.0 ports to be controlled by the xHCI host.
*/
pci_read_config_dword(xhci_pdev, USB_INTEL_USB2PRM,
&ports_available);
dev_dbg(&xhci_pdev->dev, "Configurable USB 2.0 ports to hand over to xCHI: 0x%x\n",
ports_available);
/* Write XUSB2PR, the xHC USB 2.0 Port Routing Register, to
* switch the USB 2.0 power and data lines over to the xHCI
* host.
*/
pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
cpu_to_le32(ports_available));
pci_read_config_dword(xhci_pdev, USB_INTEL_XUSB2PR,
&ports_available);
dev_dbg(&xhci_pdev->dev, "USB 2.0 ports that are now switched over "
"to xHCI: 0x%x\n", ports_available);
}
EXPORT_SYMBOL_GPL(usb_enable_xhci_ports);
void usb_disable_xhci_ports(struct pci_dev *xhci_pdev)
{
pci_write_config_dword(xhci_pdev, USB_INTEL_USB3_PSSEN, 0x0);
pci_write_config_dword(xhci_pdev, USB_INTEL_XUSB2PR, 0x0);
}
EXPORT_SYMBOL_GPL(usb_disable_xhci_ports);
/**
* PCI Quirks for xHCI.
*
* Takes care of the handoff between the Pre-OS (i.e. BIOS) and the OS.
* It signals to the BIOS that the OS wants control of the host controller,
* and then waits 5 seconds for the BIOS to hand over control.
* If we timeout, assume the BIOS is broken and take control anyway.
*/
static void quirk_usb_handoff_xhci(struct pci_dev *pdev)
{
void __iomem *base;
int ext_cap_offset;
void __iomem *op_reg_base;
u32 val;
int timeout;
int len = pci_resource_len(pdev, 0);
if (!mmio_resource_enabled(pdev, 0))
return;
base = ioremap_nocache(pci_resource_start(pdev, 0), len);
if (base == NULL)
return;
/*
* Find the Legacy Support Capability register -
* this is optional for xHCI host controllers.
*/
ext_cap_offset = xhci_find_next_cap_offset(base, XHCI_HCC_PARAMS_OFFSET);
do {
if ((ext_cap_offset + sizeof(val)) > len) {
/* We're reading garbage from the controller */
dev_warn(&pdev->dev,
"xHCI controller failing to respond");
return;
}
if (!ext_cap_offset)
/* We've reached the end of the extended capabilities */
goto hc_init;
val = readl(base + ext_cap_offset);
if (XHCI_EXT_CAPS_ID(val) == XHCI_EXT_CAPS_LEGACY)
break;
ext_cap_offset = xhci_find_next_cap_offset(base, ext_cap_offset);
} while (1);
/* If the BIOS owns the HC, signal that the OS wants it, and wait */
if (val & XHCI_HC_BIOS_OWNED) {
writel(val | XHCI_HC_OS_OWNED, base + ext_cap_offset);
/* Wait for 5 seconds with 10 microsecond polling interval */
timeout = handshake(base + ext_cap_offset, XHCI_HC_BIOS_OWNED,
0, 5000, 10);
/* Assume a buggy BIOS and take HC ownership anyway */
if (timeout) {
dev_warn(&pdev->dev, "xHCI BIOS handoff failed"
" (BIOS bug ?) %08x\n", val);
writel(val & ~XHCI_HC_BIOS_OWNED, base + ext_cap_offset);
}
}
val = readl(base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET);
/* Mask off (turn off) any enabled SMIs */
val &= XHCI_LEGACY_DISABLE_SMI;
/* Mask all SMI events bits, RW1C */
val |= XHCI_LEGACY_SMI_EVENTS;
/* Disable any BIOS SMIs and clear all SMI events*/
writel(val, base + ext_cap_offset + XHCI_LEGACY_CONTROL_OFFSET);
hc_init:
if (usb_is_intel_switchable_xhci(pdev))
usb_enable_xhci_ports(pdev);
op_reg_base = base + XHCI_HC_LENGTH(readl(base));
/* Wait for the host controller to be ready before writing any
* operational or runtime registers. Wait 5 seconds and no more.
*/
timeout = handshake(op_reg_base + XHCI_STS_OFFSET, XHCI_STS_CNR, 0,
5000, 10);
/* Assume a buggy HC and start HC initialization anyway */
if (timeout) {
val = readl(op_reg_base + XHCI_STS_OFFSET);
dev_warn(&pdev->dev,
"xHCI HW not ready after 5 sec (HC bug?) "
"status = 0x%x\n", val);
}
/* Send the halt and disable interrupts command */
val = readl(op_reg_base + XHCI_CMD_OFFSET);
val &= ~(XHCI_CMD_RUN | XHCI_IRQS);
writel(val, op_reg_base + XHCI_CMD_OFFSET);
/* Wait for the HC to halt - poll every 125 usec (one microframe). */
timeout = handshake(op_reg_base + XHCI_STS_OFFSET, XHCI_STS_HALT, 1,
XHCI_MAX_HALT_USEC, 125);
if (timeout) {
val = readl(op_reg_base + XHCI_STS_OFFSET);
dev_warn(&pdev->dev,
"xHCI HW did not halt within %d usec "
"status = 0x%x\n", XHCI_MAX_HALT_USEC, val);
}
iounmap(base);
}
/* PCI Quirks for Intel MOFD OTG3 controller
*
* For FS device connection, there have some noise after D+ drive stage.
* The USB PHY treat the noise as chirp J which actually haven't get the
* chirp J target defined in USB spec (D+ - D- > 300mv). Then controller
* trying to do HS negotiation, finally get FS device disconnect after port
* reset.
*
* This is UTMI PHY bug which violate spec for detect chirp J.
*
* The WA is set UTMI PHY register to avoid the noise.
*
**/
#define USB2_COMPBG_ADDR 0xf90b1110
#define USB2_COMPBG_HSSQREFBEN(x) ((x & 0x3) << 11)
#define USB2_COMPBG_HSSQREFEN(x) ((x & 0x3) << 13)
#define USB2_COMPBG_HSSQREFEN_MASK (0x3 << 13)
#define USB2_COMPBG_HSSQREFBEN_MASK (0x3 << 11)
static void __iomem *usb2_compbg;
int quirk_intel_xhci_pr_init(bool init)
{
if (init) {
usb2_compbg = ioremap_nocache(USB2_COMPBG_ADDR, 4);
if (!usb2_compbg)
return -ENOMEM;
} else
iounmap(usb2_compbg);
return 0;
}
int quirk_intel_xhci_port_reset(struct device *dev, bool post)
{
u32 val;
static u32 original_val;
if (!usb2_compbg)
return -ENOMEM;
if (!post) {
dev_warn(dev, "Enable UTMI PHY FS WA\n");
val = readl(usb2_compbg);
original_val = val;
val &= ~(USB2_COMPBG_HSSQREFEN_MASK | USB2_COMPBG_HSSQREFBEN_MASK);
val |= USB2_COMPBG_HSSQREFEN(3) | USB2_COMPBG_HSSQREFBEN(1);
writel(val, usb2_compbg);
} else {
dev_warn(dev, "Disable UTMI PHY FS WA\n");
writel(original_val, usb2_compbg);
}
return 0;
}
static void quirk_usb_early_handoff(struct pci_dev *pdev)
{
/* Skip Netlogic mips SoC's internal PCI USB controller.
* This device does not need/support EHCI/OHCI handoff
*/
if (pdev->vendor == 0x184e) /* vendor Netlogic */
return;
if (pdev->class != PCI_CLASS_SERIAL_USB_UHCI &&
pdev->class != PCI_CLASS_SERIAL_USB_OHCI &&
pdev->class != PCI_CLASS_SERIAL_USB_EHCI &&
pdev->class != PCI_CLASS_SERIAL_USB_XHCI)
return;
if (pci_enable_device(pdev) < 0) {
dev_warn(&pdev->dev, "Can't enable PCI device, "
"BIOS handoff failed.\n");
return;
}
if (pdev->class == PCI_CLASS_SERIAL_USB_UHCI)
quirk_usb_handoff_uhci(pdev);
else if (pdev->class == PCI_CLASS_SERIAL_USB_OHCI)
quirk_usb_handoff_ohci(pdev);
else if (pdev->class == PCI_CLASS_SERIAL_USB_EHCI)
quirk_usb_disable_ehci(pdev);
else if (pdev->class == PCI_CLASS_SERIAL_USB_XHCI)
quirk_usb_handoff_xhci(pdev);
pci_disable_device(pdev);
}
DECLARE_PCI_FIXUP_CLASS_FINAL(PCI_ANY_ID, PCI_ANY_ID,
PCI_CLASS_SERIAL_USB, 8, quirk_usb_early_handoff);