| /* |
| * DDR SDRAM initialization - alter with care |
| * This file is intended to be included from other assembler files |
| * |
| * Note: This file may not modify r8 or r9 because they are used to |
| * carry information from the decompresser to the kernel |
| * |
| * Copyright (C) 2005-2007 Axis Communications AB |
| * |
| * Authors: Mikael Starvik <starvik@axis.com> |
| */ |
| |
| /* Just to be certain the config file is included, we include it here |
| * explicitely instead of depending on it being included in the file that |
| * uses this code. |
| */ |
| |
| #include <hwregs/asm/reg_map_asm.h> |
| #include <hwregs/asm/ddr2_defs_asm.h> |
| |
| ;; WARNING! The registers r8 and r9 are used as parameters carrying |
| ;; information from the decompressor (if the kernel was compressed). |
| ;; They should not be used in the code below. |
| |
| ;; Refer to ddr2 MDS for initialization sequence |
| |
| ; 2. Wait 200us |
| move.d 10000, $r2 |
| 1: bne 1b |
| subq 1, $r2 |
| |
| ; Start clock |
| move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_phy_cfg), $r0 |
| move.d REG_STATE(ddr2, rw_phy_cfg, en, yes), $r1 |
| move.d $r1, [$r0] |
| |
| ; 2. Wait 200us |
| move.d 10000, $r2 |
| 1: bne 1b |
| subq 1, $r2 |
| |
| ; Reset phy and start calibration |
| move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_phy_ctrl), $r0 |
| move.d REG_STATE(ddr2, rw_phy_ctrl, rst, yes) | \ |
| REG_STATE(ddr2, rw_phy_ctrl, cal_rst, yes), $r1 |
| move.d $r1, [$r0] |
| move.d REG_STATE(ddr2, rw_phy_ctrl, cal_start, yes), $r1 |
| move.d $r1, [$r0] |
| |
| ; 2. Wait 200us |
| move.d 10000, $r2 |
| 1: bne 1b |
| subq 1, $r2 |
| |
| ; Issue commands |
| move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_ctrl), $r0 |
| move.d sdram_commands_start, $r2 |
| command_loop: |
| movu.b [$r2+], $r1 |
| movu.w [$r2+], $r3 |
| do_cmd: |
| lslq 16, $r1 |
| or.d $r3, $r1 |
| move.d $r1, [$r0] |
| ; 2. Wait 200us |
| move.d 10000, $r4 |
| 1: bne 1b |
| subq 1, $r4 |
| cmp.d sdram_commands_end, $r2 |
| blo command_loop |
| nop |
| |
| ; Set timing |
| move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_timing), $r0 |
| move.d CONFIG_ETRAX_DDR2_TIMING, $r1 |
| move.d $r1, [$r0] |
| |
| ; Set latency |
| move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_latency), $r0 |
| move.d CONFIG_ETRAX_DDR2_LATENCY, $r1 |
| move.d $r1, [$r0] |
| |
| ; Set configuration |
| move.d REG_ADDR(ddr2, regi_ddr2_ctrl, rw_cfg), $r0 |
| move.d CONFIG_ETRAX_DDR2_CONFIG, $r1 |
| move.d $r1, [$r0] |
| |
| ba after_sdram_commands |
| nop |
| |
| sdram_commands_start: |
| .byte regk_ddr2_deselect |
| .word 0 |
| .byte regk_ddr2_pre |
| .word regk_ddr2_pre_all |
| .byte regk_ddr2_emrs2 |
| .word 0 |
| .byte regk_ddr2_emrs3 |
| .word 0 |
| .byte regk_ddr2_emrs |
| .word regk_ddr2_dll_en |
| .byte regk_ddr2_mrs |
| .word regk_ddr2_dll_rst |
| .byte regk_ddr2_pre |
| .word regk_ddr2_pre_all |
| .byte regk_ddr2_ref |
| .word 0 |
| .byte regk_ddr2_ref |
| .word 0 |
| .byte regk_ddr2_mrs |
| .word CONFIG_ETRAX_DDR2_MRS & 0xffff |
| .byte regk_ddr2_emrs |
| .word regk_ddr2_ocd_default | regk_ddr2_dll_en |
| .byte regk_ddr2_emrs |
| .word regk_ddr2_ocd_exit | regk_ddr2_dll_en | (CONFIG_ETRAX_DDR2_MRS >> 16) |
| sdram_commands_end: |
| .align 1 |
| after_sdram_commands: |
