| #include <dt-bindings/gpio/gpio.h> |
| #include "kona-pmic-overlay.dtsi" |
| #include "kona-sde-display.dtsi" |
| #include "kona-audio-overlay.dtsi" |
| #include "kona-thermal-overlay.dtsi" |
| #include "kona-xr-pinctrl-overlay.dtsi" |
| #include "camera/kona-camera-sensor-xrfusion.dtsi" |
| |
| &tlmm { |
| mag_rst_gpio_default: mag_rst_gpio_default { |
| mux { |
| pins = "gpio125"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio125"; |
| drive-strength = <8>; |
| bias-disable = <0>; |
| output-high; |
| }; |
| }; |
| |
| mag_rst_gpio_sleep: mag_rst_gpio_sleep { |
| mux { |
| pins = "gpio125"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio125"; |
| drive-strength = <8>; |
| bias-pull-down; |
| input-enable; |
| }; |
| }; |
| |
| display_panel_led1_default: display_panel_led1_default { |
| mux { |
| pins = "gpio144"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio144"; |
| drive-strength = <8>; |
| bias-disable = <0>; |
| output-high; |
| }; |
| }; |
| |
| display_panel_led2_default: display_panel_led2_default { |
| mux { |
| pins = "gpio140"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio140"; |
| drive-strength = <8>; |
| bias-disable = <0>; |
| output-high; |
| }; |
| }; |
| |
| spkr_1_sd_n { |
| spkr_1_sd_n_sleep: spkr_1_sd_n_sleep { |
| mux { |
| pins = "gpio127"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio127"; |
| drive-strength = <2>; /* 2 mA */ |
| bias-pull-down; |
| input-enable; |
| }; |
| }; |
| |
| spkr_1_sd_n_active: spkr_1_sd_n_active { |
| mux { |
| pins = "gpio127"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio127"; |
| drive-strength = <16>; /* 16 mA */ |
| bias-disable; |
| output-high; |
| }; |
| }; |
| }; |
| |
| spkr_2_sd_n { |
| spkr_2_sd_n_sleep: spkr_2_sd_n_sleep { |
| mux { |
| pins = "gpio129"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio129"; |
| drive-strength = <2>; /* 2 mA */ |
| bias-pull-down; |
| input-enable; |
| }; |
| }; |
| |
| spkr_2_sd_n_active: spkr_2_sd_n_active { |
| mux { |
| pins = "gpio129"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio129"; |
| drive-strength = <16>; /* 16 mA */ |
| bias-disable; |
| output-high; |
| }; |
| }; |
| }; |
| |
| cam_sensor_6dof_vana_active: cam_sensor_6dof_vana_active { |
| /* AVDD LDO */ |
| mux { |
| pins = "gpio43"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio43"; |
| bias-disable; /* No PULL */ |
| drive-strength = <2>; /* 2 MA */ |
| }; |
| }; |
| |
| cam_sensor_6dof_vana_suspend: cam_sensor_6dof_vana_suspend { |
| /* AVDD LDO */ |
| mux { |
| pins = "gpio43"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio43"; |
| bias-pull-down; /* PULL DOWN */ |
| drive-strength = <2>; /* 2 MA */ |
| }; |
| }; |
| |
| cam_sensor_6dof_vdig_active: cam_sensor_6dof_vdig_active { |
| /* VDIG LDO */ |
| mux { |
| pins = "gpio42"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio42"; |
| bias-disable; /* No PULL */ |
| drive-strength = <2>; /* 2 MA */ |
| }; |
| }; |
| |
| cam_sensor_6dof_vdig_suspend: cam_sensor_6dof_vdig_suspend { |
| /* VDIG LDO */ |
| mux { |
| pins = "gpio42"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio42"; |
| bias-pull-down; /* PULL DOWN */ |
| drive-strength = <2>; /* 2 MA */ |
| }; |
| }; |
| |
| cam_sensor_6dof_vio_active: cam_sensor_6dof_vio_active { |
| /* VIO LDO */ |
| mux { |
| pins = "gpio41"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio41"; |
| bias-disable; /* No PULL */ |
| drive-strength = <2>; /* 2 MA */ |
| }; |
| }; |
| |
| cam_sensor_6dof_vio_suspend: cam_sensor_6dof_vio_suspend { |
| /* VIO LDO */ |
| mux { |
| pins = "gpio41"; |
| function = "gpio"; |
| }; |
| |
| config { |
| pins = "gpio41"; |
| bias-pull-down; /* PULL DOWN */ |
| drive-strength = <2>; /* 2 MA */ |
| }; |
| }; |
| }; |
| |
| &vendor { |
| kona_xrfusion_batterydata: qcom,battery-data { |
| qcom,batt-id-range-pct = <15>; |
| #include "fg-gen4-batterydata-goertek-6100mah.dtsi" |
| }; |
| }; |
| |
| &qupv3_se12_2uart { |
| status = "okay"; |
| }; |
| |
| &pm8150a_amoled { |
| status = "disabled"; |
| }; |
| |
| &qupv3_se6_4uart { |
| status = "ok"; |
| }; |
| |
| &dai_mi2s2 { |
| status = "disabled"; |
| qcom,msm-mi2s-tx-lines = <1>; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&tert_mi2s_sck_active &tert_mi2s_ws_active |
| &tert_mi2s_sd0_active>; |
| pinctrl-1 = <&tert_mi2s_sck_sleep &tert_mi2s_ws_sleep |
| &tert_mi2s_sd0_sleep>; |
| }; |
| |
| &kona_snd { |
| qcom,model = "kona-xrfusionult-snd-card"; |
| qcom,mi2s-audio-intf = <0>; |
| qcom,audio-routing = |
| "AMIC1", "MIC BIAS1", |
| "MIC BIAS1", "Analog Mic1", |
| "AMIC2", "MIC BIAS2", |
| "MIC BIAS2", "Analog Mic2", |
| "AMIC3", "MIC BIAS3", |
| "MIC BIAS3", "Analog Mic3", |
| "AMIC4", "MIC BIAS4", |
| "MIC BIAS4", "Analog Mic4", |
| "AMIC5", "MIC BIAS4", |
| "MIC BIAS4", "Analog Mic5", |
| "DMIC1", "MIC BIAS1", |
| "MIC BIAS1", "Digital Mic0", |
| "DMIC2", "MIC BIAS1", |
| "MIC BIAS1", "Digital Mic1", |
| "DMIC3", "MIC BIAS1", |
| "MIC BIAS1", "Digital Mic2", |
| "DMIC4", "MIC BIAS1", |
| "MIC BIAS1", "Digital Mic3", |
| "DMIC5", "MIC BIAS3", |
| "MIC BIAS3", "Digital Mic4", |
| "DMIC6", "MIC BIAS3", |
| "MIC BIAS3", "Digital Mic5", |
| "DMIC7", "MIC BIAS4", |
| "MIC BIAS4", "Digital Mic6", |
| "DMIC8", "MIC BIAS4", |
| "MIC BIAS4", "Digital Mic7", |
| "IN1_HPHL", "HPHL_OUT", |
| "IN2_HPHR", "HPHR_OUT", |
| "IN3_AUX", "AUX_OUT", |
| "TX SWR_ADC0", "ADC1_OUTPUT", |
| "TX SWR_ADC1", "ADC2_OUTPUT", |
| "TX SWR_ADC2", "ADC3_OUTPUT", |
| "TX SWR_ADC3", "ADC4_OUTPUT", |
| "TX SWR_DMIC0", "DMIC1_OUTPUT", |
| "TX SWR_DMIC1", "DMIC2_OUTPUT", |
| "TX SWR_DMIC2", "DMIC3_OUTPUT", |
| "TX SWR_DMIC3", "DMIC4_OUTPUT", |
| "TX SWR_DMIC4", "DMIC5_OUTPUT", |
| "TX SWR_DMIC5", "DMIC6_OUTPUT", |
| "TX SWR_DMIC6", "DMIC7_OUTPUT", |
| "TX SWR_DMIC7", "DMIC8_OUTPUT", |
| "WSA SRC0_INP", "SRC0", |
| "WSA_TX DEC0_INP", "TX DEC0 MUX", |
| "WSA_TX DEC1_INP", "TX DEC1 MUX", |
| "RX_TX DEC0_INP", "TX DEC0 MUX", |
| "RX_TX DEC1_INP", "TX DEC1 MUX", |
| "RX_TX DEC2_INP", "TX DEC2 MUX", |
| "RX_TX DEC3_INP", "TX DEC3 MUX", |
| "SpkrRight IN", "WSA_SPK2 OUT", |
| "VA_AIF1 CAP", "VA_SWR_CLK", |
| "VA_AIF2 CAP", "VA_SWR_CLK", |
| "VA_AIF3 CAP", "VA_SWR_CLK", |
| "VA MIC BIAS3", "Digital Mic0", |
| "VA MIC BIAS3", "Digital Mic1", |
| "VA MIC BIAS1", "Digital Mic2", |
| "VA MIC BIAS1", "Digital Mic3", |
| "VA MIC BIAS4", "Digital Mic5", |
| "VA DMIC0", "VA MIC BIAS3", |
| "VA DMIC1", "VA MIC BIAS3", |
| "VA DMIC2", "VA MIC BIAS1", |
| "VA DMIC3", "VA MIC BIAS1", |
| "VA DMIC5", "VA MIC BIAS4", |
| "VA SWR_ADC1", "VA_SWR_CLK", |
| "VA SWR_MIC0", "VA_SWR_CLK", |
| "VA SWR_MIC1", "VA_SWR_CLK", |
| "VA SWR_MIC2", "VA_SWR_CLK", |
| "VA SWR_MIC3", "VA_SWR_CLK", |
| "VA SWR_MIC4", "VA_SWR_CLK", |
| "VA SWR_MIC5", "VA_SWR_CLK", |
| "VA SWR_MIC6", "VA_SWR_CLK", |
| "VA SWR_MIC7", "VA_SWR_CLK", |
| "VA SWR_MIC0", "DMIC1_OUTPUT", |
| "VA SWR_MIC1", "DMIC2_OUTPUT", |
| "VA SWR_MIC2", "DMIC3_OUTPUT", |
| "VA SWR_MIC3", "DMIC4_OUTPUT", |
| "VA SWR_MIC4", "DMIC5_OUTPUT", |
| "VA SWR_MIC5", "DMIC6_OUTPUT", |
| "VA SWR_MIC6", "DMIC7_OUTPUT", |
| "VA SWR_MIC7", "DMIC8_OUTPUT", |
| "VA SWR_ADC1", "ADC2_OUTPUT"; |
| qcom,msm-mbhc-hphl-swh = <1>; |
| qcom,msm-mbhc-gnd-swh = <1>; |
| qcom,cdc-dmic01-gpios = <&cdc_dmic01_gpios>; |
| qcom,cdc-dmic23-gpios = <&cdc_dmic23_gpios>; |
| qcom,cdc-dmic45-gpios = <&cdc_dmic45_gpios>; |
| asoc-codec = <&stub_codec>, <&bolero>, <&ext_disp_audio_codec>; |
| asoc-codec-names = "msm-stub-codec.1", "bolero_codec", |
| "msm-ext-disp-audio-codec-rx"; |
| qcom,wsa-max-devs = <2>; |
| qcom,wsa-devs = <&wsa881x_0211>, <&wsa881x_0212>, |
| <&wsa881x_0213>, <&wsa881x_0214>; |
| qcom,wsa-aux-dev-prefix = "SpkrLeft", "SpkrRight", |
| "SpkrLeft", "SpkrRight"; |
| qcom,codec-max-aux-devs = <1>; |
| qcom,codec-aux-devs = <&wcd938x_codec>; |
| qcom,msm_audio_ssr_devs = <&audio_apr>, <&q6core>, <&lpi_tlmm>, |
| <&bolero>; |
| }; |
| |
| &pm8150_l10 { |
| regulator-max-microvolt = <3304000>; |
| qcom,init-voltage = <3304000>; |
| }; |
| |
| &qupv3_se1_i2c { |
| status = "ok"; |
| qcom,clk-freq-out = <1000000>; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| xrfancontroller: xrfancontroller@50 { |
| compatible = "maxim,xrfancontroller"; |
| reg = <0x50>; |
| /* Manetometer gpio */ |
| mag_rst_gpio = <&tlmm 125 0>; |
| enable-active-high; |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&mag_rst_gpio_default>; |
| pinctrl-1 = <&mag_rst_gpio_sleep>; |
| qcom,fan-pwr-en = <&tlmm 38 0x00>; |
| qcom,fan-pwr-bp = <&tlmm 39 0x00>; |
| }; |
| }; |
| |
| &qupv3_se13_i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| status = "disabled"; |
| }; |
| |
| &ufsphy_mem { |
| compatible = "qcom,ufs-phy-qmp-v4"; |
| |
| vdda-phy-supply = <&pm8150_l5>; |
| vdda-phy-always-on; |
| vdda-pll-supply = <&pm8150_l9>; |
| vdda-phy-max-microamp = <89900>; |
| vdda-pll-max-microamp = <18800>; |
| |
| status = "ok"; |
| }; |
| |
| &ufshc_mem { |
| vdd-hba-supply = <&ufs_phy_gdsc>; |
| vdd-hba-fixed-regulator; |
| vcc-supply = <&pm8150_l17>; |
| vcc-voltage-level = <2504000 2950000>; |
| vcc-low-voltage-sup; |
| vccq-supply = <&pm8150_l6>; |
| vccq2-supply = <&pm8150_s4>; |
| vcc-max-microamp = <800000>; |
| vccq-max-microamp = <800000>; |
| vccq2-max-microamp = <800000>; |
| |
| qcom,vddp-ref-clk-supply = <&pm8150_l6>; |
| qcom,vddp-ref-clk-max-microamp = <100>; |
| qcom,vccq-parent-supply = <&pm8150a_s8>; |
| qcom,vccq-parent-max-microamp = <210000>; |
| |
| status = "ok"; |
| }; |
| |
| &soc { |
| gpio_keys { |
| compatible = "gpio-keys"; |
| label = "gpio-keys"; |
| |
| pinctrl-names = "default"; |
| pinctrl-0 = <&key_vol_up_default |
| &key_confirm_default |
| &key_vol_up_default>; |
| |
| home { |
| label = "home"; |
| gpios = <&pm8150_gpios 1 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_BACK>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| confirm { |
| label = "confirm"; |
| gpios = <&pm8150_gpios 7 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_ENTER>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| |
| vol_up { |
| label = "volume_up"; |
| gpios = <&pm8150_gpios 6 GPIO_ACTIVE_LOW>; |
| linux,input-type = <1>; |
| linux,code = <KEY_VOLUMEUP>; |
| gpio-key,wakeup; |
| debounce-interval = <15>; |
| linux,can-disable; |
| }; |
| }; |
| |
| qcom,qbt_handler { |
| status = "disabled"; |
| }; |
| |
| qcom,xr-stdalonevwr-misc { |
| compatible = "qcom,xr-stdalonevwr-misc"; |
| /* IMU CLK Enable PM8150 GPIO 3 */ |
| pinctrl-names = "default", "sleep"; |
| pinctrl-0 = <&imu_clkin_default>; |
| pinctrl-1 = <&imu_clkin_sleep>; |
| }; |
| }; |
| |
| &vreg_hap_boost { |
| status = "ok"; |
| }; |
| |
| &pm8150b_haptics { |
| qcom,vmax-mv = <1697>; |
| qcom,play-rate-us = <5882>; |
| vdd-supply = <&vreg_hap_boost>; |
| |
| wf_0 { |
| /* CLICK */ |
| qcom,wf-play-rate-us = <5882>; |
| qcom,wf-vmax-mv = <1697>; |
| }; |
| |
| wf_1 { |
| /* DOUBLE CLICK */ |
| qcom,wf-play-rate-us = <5882>; |
| qcom,wf-vmax-mv = <1697>; |
| }; |
| |
| wf_2 { |
| /* TICK */ |
| qcom,wf-play-rate-us = <5882>; |
| qcom,wf-vmax-mv = <1697>; |
| }; |
| |
| wf_3 { |
| /* THUD */ |
| qcom,wf-play-rate-us = <5882>; |
| qcom,wf-vmax-mv = <1697>; |
| }; |
| |
| wf_4 { |
| /* POP */ |
| qcom,wf-play-rate-us = <5882>; |
| qcom,wf-vmax-mv = <1697>; |
| }; |
| |
| wf_5 { |
| /* HEAVY CLICK */ |
| qcom,wf-play-rate-us = <5882>; |
| qcom,wf-vmax-mv = <1697>; |
| }; |
| }; |
| |
| &pm8150b_vadc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vph_pwr@83 { |
| reg = <ADC_VPH_PWR>; |
| label = "vph_pwr"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| conn_therm@4f { |
| reg = <ADC_AMUX_THM3_PU2>; |
| label = "conn_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| chg_sbux@99 { |
| reg = <ADC_SBUx>; |
| label = "chg_sbux"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| mid_chg_div6@1e { |
| reg = <ADC_MID_CHG_DIV6>; |
| label = "chg_mid"; |
| qcom,pre-scaling = <1 6>; |
| }; |
| |
| usb_in_i_uv@7 { |
| reg = <ADC_USB_IN_I>; |
| label = "usb_in_i_uv"; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| usb_in_v_div_16@8 { |
| reg = <ADC_USB_IN_V_16>; |
| label = "usb_in_v_div_16"; |
| qcom,pre-scaling = <1 16>; |
| }; |
| }; |
| |
| &qupv3_se15_i2c { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| status = "ok"; |
| redriver: redriver@1c { |
| compatible = "onnn,redriver"; |
| reg = <0x1c>; |
| extcon = <&pm8150b_pdphy>, <&pm8150b_pdphy>; |
| eq = /bits/ 8 < |
| /* Parameters for USB */ |
| 0x4 0x4 0x4 0x4 |
| /* Parameters for DP */ |
| 0x6 0x4 0x4 0x6>; |
| flat-gain = /bits/ 8 < |
| /* Parameters for USB */ |
| 0x3 0x1 0x1 0x3 |
| /* Parameters for DP */ |
| 0x2 0x1 0x1 0x2>; |
| output-comp = /bits/ 8 < |
| /* Parameters for USB */ |
| 0x3 0x3 0x3 0x3 |
| /* Parameters for DP */ |
| 0x3 0x3 0x3 0x3>; |
| loss-match = /bits/ 8 < |
| /* Parameters for USB */ |
| 0x1 0x3 0x3 0x1 |
| /* Parameters for DP */ |
| 0x3 0x3 0x3 0x3>; |
| }; |
| |
| #include "smb1390.dtsi" |
| }; |
| |
| &smb1390 { |
| pinctrl-names = "default"; |
| pinctrl-0 = <&smb_stat_default>; |
| status = "ok"; |
| }; |
| |
| &smb1390_charger { |
| io-channels = <&pm8150b_vadc ADC_AMUX_THM2>; |
| io-channel-names = "cp_die_temp"; |
| qcom,parallel-output-mode = <2>; |
| status = "ok"; |
| }; |
| |
| &smb1390_slave { |
| status = "ok"; |
| }; |
| |
| &smb1390_slave_charger { |
| status = "ok"; |
| }; |
| |
| &pm8150b_charger { |
| status = "ok"; |
| qcom,sec-charger-config = <1>; |
| qcom,auto-recharge-soc = <98>; |
| io-channels = <&pm8150b_vadc ADC_MID_CHG_DIV6>, |
| <&pm8150b_vadc ADC_USB_IN_I>, |
| <&pm8150b_vadc ADC_SBUx>, |
| <&pm8150b_vadc ADC_VPH_PWR>, |
| <&pm8150b_vadc ADC_CHG_TEMP>; |
| io-channel-names = "mid_voltage", |
| "usb_in_current", |
| "sbux_res", |
| "vph_voltage", |
| "chg_temp"; |
| qcom,battery-data = <&kona_xrfusion_batterydata>; |
| qcom,sw-jeita-enable; |
| qcom,wd-bark-time-secs = <16>; |
| qcom,suspend-input-on-debug-batt; |
| qcom,thermal-mitigation = <5325000 4500000 4000000 3500000 3000000 |
| 2500000 2000000 1500000 1000000 500000>; |
| }; |
| |
| &pm8150b_fg { |
| status = "ok"; |
| qcom,battery-data = <&kona_xrfusion_batterydata>; |
| qcom,hold-soc-while-full; |
| qcom,linearize-soc; |
| qcom,five-pin-battery; |
| qcom,cl-wt-enable; |
| qcom,soc-scale-mode-en; |
| /* ESR fast calibration */ |
| qcom,fg-esr-timer-chg-fast = <0 7>; |
| qcom,fg-esr-timer-dischg-fast = <0 7>; |
| qcom,fg-esr-timer-chg-slow = <0 96>; |
| qcom,fg-esr-timer-dischg-slow = <0 96>; |
| qcom,fg-esr-cal-soc-thresh = <26 230>; |
| qcom,fg-esr-cal-temp-thresh = <10 40>; |
| }; |
| |
| &pm8150_vadc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vph_pwr@83 { |
| reg = <ADC_VPH_PWR>; |
| label = "vph_pwr"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| vcoin@85 { |
| reg = <ADC_VCOIN>; |
| label = "vcoin"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| xo_therm@4c { |
| reg = <ADC_XO_THERM_PU2>; |
| label = "xo_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| skin_therm@4d { |
| reg = <ADC_AMUX_THM1_PU2>; |
| label = "skin_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm1@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| label = "pa_therm1"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| }; |
| |
| &pm8150l_vadc { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| vph_pwr@83 { |
| reg = <ADC_VPH_PWR>; |
| label = "vph_pwr"; |
| qcom,pre-scaling = <1 3>; |
| }; |
| |
| camera_flash_therm@4d { |
| reg = <ADC_AMUX_THM1_PU2>; |
| label = "camera_flash_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| skin_msm_therm@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| label = "skin_msm_therm"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| |
| pa_therm2@4f { |
| reg = <ADC_AMUX_THM3_PU2>; |
| label = "pa_therm2"; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| qcom,pre-scaling = <1 1>; |
| }; |
| }; |
| |
| &pm8150b_adc_tm { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| io-channels = <&pm8150b_vadc ADC_AMUX_THM3_PU2>; |
| |
| conn_therm@4f { |
| reg = <ADC_AMUX_THM3_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| &pm8150_adc_tm { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| io-channels = <&pm8150_vadc ADC_XO_THERM_PU2>, |
| <&pm8150_vadc ADC_AMUX_THM1_PU2>, |
| <&pm8150_vadc ADC_AMUX_THM2_PU2>; |
| |
| xo_therm@4c { |
| reg = <ADC_XO_THERM_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| skin_therm@4d { |
| reg = <ADC_AMUX_THM1_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| pa_therm1@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| &pm8150l_adc_tm { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| camera_flash_therm@4d { |
| reg = <ADC_AMUX_THM1_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| skin_msm_therm@4e { |
| reg = <ADC_AMUX_THM2_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| |
| pa_therm2@4f { |
| reg = <ADC_AMUX_THM3_PU2>; |
| qcom,ratiometric; |
| qcom,hw-settle-time = <200>; |
| }; |
| }; |
| |
| &spmi_debug_bus { |
| status = "ok"; |
| }; |
| |
| &sde_dsi { |
| avdd-supply = <&display_panel_avdd>; |
| lab-supply = <&lcdb_ldo_vreg>; |
| ibb-supply = <&lcdb_ncp_vreg>; |
| qcom,dsi-default-panel = <&dsi_dual_xrsmrtvwr_jdi_video>; |
| }; |
| |
| &display_panel_avdd { |
| display_panel_led1_gpio = <&tlmm 144 0>; |
| display_panel_led2_gpio = <&tlmm 140 0>; |
| enable-active-high; |
| regulator-boot-on; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&display_panel_led1_default |
| &display_panel_led2_default>; |
| }; |
| |
| &dsi_panel_pwr_supply_lab_ibb { |
| qcom,panel-supply-entry@3 { |
| reg = <1>; |
| qcom,supply-name = "avdd"; |
| qcom,supply-min-voltage = <4600000>; |
| qcom,supply-max-voltage = <6000000>; |
| qcom,supply-enable-load = <100000>; |
| qcom,supply-disable-load = <100>; |
| }; |
| }; |
| |
| &pm8150l_lcdb { |
| status = "ok"; |
| }; |
| |
| &pm8150l_wled { |
| status = "ok"; |
| }; |
| |
| &dsi_sw43404_amoled_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-te-gpio = <&tlmm 66 0>; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>; |
| }; |
| |
| &dsi_sw43404_amoled_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>; |
| }; |
| |
| &dsi_sw43404_amoled_fhd_plus_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <1023>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-te-gpio = <&tlmm 66 0>; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| qcom,mdss-dsi-panel-test-pin = <&tlmm 46 0>; |
| }; |
| |
| &dsi_sim_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_sim_vid { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_sim_dsc_375_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_sim_dsc_10b_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_dual_sim_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_dual_sim_vid { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &dsi_dual_sim_dsc_375_cmd { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_dcs"; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| }; |
| |
| &thermal_zones { |
| conn-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150b_adc_tm ADC_AMUX_THM3_PU2>; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| xo-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150_adc_tm ADC_XO_THERM_PU2>; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| skin-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150_adc_tm ADC_AMUX_THM1_PU2>; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| mmw-pa1-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150_adc_tm ADC_AMUX_THM2_PU2>; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| camera-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM1_PU2>; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| skin-msm-therm-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM2_PU2>; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| |
| mmw-pa2-usr { |
| polling-delay-passive = <0>; |
| polling-delay = <0>; |
| thermal-governor = "user_space"; |
| thermal-sensors = <&pm8150l_adc_tm ADC_AMUX_THM3_PU2>; |
| trips { |
| active-config0 { |
| temperature = <125000>; |
| hysteresis = <1000>; |
| type = "passive"; |
| }; |
| }; |
| }; |
| }; |
| |
| &sdhc_2 { |
| vdd-supply = <&pm8150a_l9>; |
| qcom,vdd-voltage-level = <2950000 2960000>; |
| qcom,vdd-current-level = <200 800000>; |
| |
| vdd-io-supply = <&pm8150a_l6>; |
| qcom,vdd-io-voltage-level = <1808000 2960000>; |
| qcom,vdd-io-current-level = <200 22000>; |
| |
| pinctrl-names = "active", "sleep"; |
| pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &storage_cd>; |
| pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &storage_cd>; |
| |
| cd-gpios = <&tlmm 77 GPIO_ACTIVE_HIGH>; /* Morpheus has to be HIGH */ |
| |
| status = "ok"; |
| }; |
| |
| &vendor { |
| bluetooth: bt_qca6390 { |
| compatible = "qca,qca6390"; |
| pinctrl-names = "default"; |
| pinctrl-0 = <&bt_en_sleep>; |
| qca,bt-reset-gpio = <&tlmm 21 0>; /* BT_EN */ |
| qca,bt-sw-ctrl-gpio = <&tlmm 124 0>; /* SW_CTRL */ |
| qca,bt-vdd-aon-supply = <&pm8150_s6>; |
| qca,bt-vdd-dig-supply = <&pm8009_s2>; |
| qca,bt-vdd-rfa1-supply = <&pm8150_s5>; |
| qca,bt-vdd-rfa2-supply = <&pm8150a_s8>; |
| qca,bt-vdd-asd-supply = <&pm8150_l16>; |
| |
| qca,bt-vdd-aon-voltage-level = <950000 950000>; |
| qca,bt-vdd-dig-voltage-level = <950000 952000>; |
| qca,bt-vdd-rfa1-voltage-level = <1900000 1900000>; |
| qca,bt-vdd-rfa2-voltage-level = <1350000 1350000>; |
| qca,bt-vdd-asd-voltage-level = <3024000 3304000>; |
| |
| qca,bt-vdd-asd-current-level = <10000>; |
| }; |
| }; |
| |
| &usb0 { |
| dwc3@a600000 { |
| maximum-speed = "super-speed-plus"; |
| }; |
| }; |
| |
| &usb1 { |
| qcom,default-mode-none; |
| }; |
| |
| &wil6210 { |
| status = "ok"; |
| }; |
| |
| &usb2_phy0 { |
| qcom,param-override-seq = |
| <0xc7 0x6c |
| 0x0f 0x70 |
| 0x03 0x74>; |
| }; |
| |
| &mdss_mdp { |
| qcom,sde-mixer-display-pref = "primary", "primary", "primary", |
| "primary", "none", "none"; |
| connectors = <&sde_dp &sde_dsi &sde_dsi1 &sde_rscc>; |
| }; |
| |
| &sde_wb { |
| status = "disabled"; |
| }; |
| |
| &dsi_dual_xrsmrtvwr_jdi_video { |
| qcom,panel-supply-entries = <&dsi_panel_pwr_supply_lab_ibb>; |
| qcom,mdss-dsi-bl-pmic-control-type = "bl_ctrl_external"; |
| qcom,mdss-dsi-bl-min-level = <1>; |
| qcom,mdss-dsi-bl-max-level = <4095>; |
| qcom,mdss-brightness-max-level = <255>; |
| qcom,platform-reset-gpio = <&tlmm 75 0>; |
| qcom,platform-te-gpio = <&tlmm 66 0>; |
| |
| qcom,platform-bklight-en-gpio = <&tlmm 133 0>; |
| qcom,5v-boost-gpio = <&tlmm 134 0>; |
| /delete-property/ qcom,platform-en-gpio; |
| |
| qcom,mdss-dsi-panel-status-command = [06 01 00 01 00 00 01 0a]; |
| qcom,mdss-dsi-panel-status-command-state = "dsi_hs_mode"; |
| qcom,mdss-dsi-panel-status-value = <0x9c>; |
| qcom,mdss-dsi-panel-on-check-value = <0x9c>; |
| qcom,mdss-dsi-panel-status-read-length = <1>; |
| qcom,dsi-select-clocks = "mux_byte_clk0", "mux_pixel_clk0"; |
| qcom,mdss-dsi-min-refresh-rate = <60>; |
| qcom,mdss-dsi-max-refresh-rate = <90>; |
| qcom,mdss-dsi-display-timings { |
| timing@0 { |
| qcom,mdss-dsi-panel-width = <2160>; |
| qcom,mdss-dsi-panel-height = <2160>; |
| qcom,mdss-dsi-h-front-porch = <20>; |
| qcom,mdss-dsi-h-back-porch = <20>; |
| qcom,mdss-dsi-h-pulse-width = <20>; |
| qcom,mdss-dsi-h-sync-skew = <0>; |
| qcom,mdss-dsi-v-back-porch = <20>; |
| qcom,mdss-dsi-v-front-porch = <936>; |
| qcom,mdss-dsi-v-pulse-width = <4>; |
| qcom,mdss-dsi-panel-framerate = <90>; |
| qcom,mdss-dsi-on-command = [ |
| 29 01 00 00 00 00 02 B0 04 |
| 29 01 00 00 00 00 02 D6 00 |
| 29 01 00 00 00 00 0A B6 30 6B 80 06 33 |
| 8A 00 1A 7A |
| 29 01 00 00 00 00 05 B7 54 00 00 00 |
| 29 01 00 00 00 00 05 B9 10 00 01 38 |
| 29 01 00 00 00 00 09 C0 51 86 64 00 08 |
| 70 07 00 |
| 29 01 00 00 00 00 02 F1 1E |
| 29 01 00 00 00 00 11 C6 70 08 D0 02 21 |
| 6F 08 5A 00 00 00 00 00 00 00 00 |
| 29 01 00 00 00 00 02 CD 00 |
| 29 01 00 00 00 00 08 CF 8B 00 80 46 61 |
| 00 8B |
| 29 01 00 00 00 00 06 EC 02 96 00 00 00 |
| 39 01 00 00 00 00 02 03 01 |
| 39 01 00 00 00 00 03 44 00 00 |
| 39 01 00 00 00 00 02 35 00 |
| 39 01 00 00 00 00 02 36 00 |
| 39 01 00 00 00 00 02 3A 77 |
| 05 01 00 00 02 00 02 29 00 |
| 05 01 00 00 80 00 02 11 00 |
| 29 01 00 00 00 00 02 D6 80 |
| 29 01 00 00 00 00 02 B0 03 |
| ]; |
| qcom,mdss-dsi-off-command = [ |
| 05 01 00 00 32 00 02 28 00 |
| 05 01 00 00 32 00 02 34 00 |
| 05 01 00 00 78 00 02 10 00 |
| ]; |
| qcom,mdss-dsi-on-command-state = "dsi_lp_mode"; |
| qcom,mdss-dsi-off-command-state = "dsi_hs_mode"; |
| qcom,mdss-dsi-h-sync-pulse = <0>; |
| qcom,compression-mode = "dsc"; |
| qcom,mdss-dsc-slice-height = <8>; |
| qcom,mdss-dsc-slice-width = <540>; |
| qcom,mdss-dsc-slice-per-pkt = <2>; |
| qcom,mdss-dsc-bit-per-component = <8>; |
| qcom,mdss-dsc-bit-per-pixel = <8>; |
| qcom,mdss-dsc-block-prediction-enable; |
| qcom,mdss-dsi-panel-phy-timings = [00 17 05 05 20 1F |
| 06 06 03 02 04 00 13 15]; |
| qcom,display-topology = <4 4 2>, |
| <1 0 2>; |
| qcom,default-topology-index = <0>; |
| |
| }; |
| }; |
| }; |
| |
| &pcie0 { |
| qcom,target-link-speed = <0x2>; |
| }; |
