android13-5.15 June 2023 release 2

Artifacts:
  https://ci.android.com/builds/submitted/10433556/kernel_aarch64/latest
BACKPORT: scsi: ufs: core: Fix devfreq deadlocks

[ Upstream commit ba81043753fffbc2ad6e0c5ff2659f12ac2f46b4 ]

There is a lock inversion and rwsem read-lock recursion in the devfreq
target callback which can lead to deadlocks.

Specifically, ufshcd_devfreq_scale() already holds a clk_scaling_lock
read lock when toggling the write booster, which involves taking the
dev_cmd mutex before taking another clk_scaling_lock read lock.

This can lead to a deadlock if another thread:

  1) tries to acquire the dev_cmd and clk_scaling locks in the correct
     order, or

  2) takes a clk_scaling write lock before the attempt to take the
     clk_scaling read lock a second time.

Fix this by dropping the clk_scaling_lock before toggling the write booster
as was done before commit 0e9d4ca43ba8 ("scsi: ufs: Protect some contexts
from unexpected clock scaling").

While the devfreq callbacks are already serialised, add a second
serialising mutex to handle the unlikely case where a callback triggered
through the devfreq sysfs interface is racing with a request to disable
clock scaling through the UFS controller 'clkscale_enable' sysfs
attribute. This could otherwise lead to the write booster being left
disabled after having disabled clock scaling.

Also take the new mutex in ufshcd_clk_scaling_allow() to make sure that any
pending write booster update has completed on return.

Note that this currently only affects Qualcomm platforms since commit
87bd05016a64 ("scsi: ufs: core: Allow host driver to disable wb toggling
during clock scaling").

The lock inversion (i.e. 1 above) was reported by lockdep as:

 ======================================================
 WARNING: possible circular locking dependency detected
 6.1.0-next-20221216 #211 Not tainted
 ------------------------------------------------------
 kworker/u16:2/71 is trying to acquire lock:
 ffff076280ba98a0 (&hba->dev_cmd.lock){+.+.}-{3:3}, at: ufshcd_query_flag+0x50/0x1c0

 but task is already holding lock:
 ffff076280ba9cf0 (&hba->clk_scaling_lock){++++}-{3:3}, at: ufshcd_devfreq_scale+0x2b8/0x380

 which lock already depends on the new lock.
[  +0.011606]
 the existing dependency chain (in reverse order) is:

 -> #1 (&hba->clk_scaling_lock){++++}-{3:3}:
        lock_acquire+0x68/0x90
        down_read+0x58/0x80
        ufshcd_exec_dev_cmd+0x70/0x2c0
        ufshcd_verify_dev_init+0x68/0x170
        ufshcd_probe_hba+0x398/0x1180
        ufshcd_async_scan+0x30/0x320
        async_run_entry_fn+0x34/0x150
        process_one_work+0x288/0x6c0
        worker_thread+0x74/0x450
        kthread+0x118/0x120
        ret_from_fork+0x10/0x20

 -> #0 (&hba->dev_cmd.lock){+.+.}-{3:3}:
        __lock_acquire+0x12a0/0x2240
        lock_acquire.part.0+0xcc/0x220
        lock_acquire+0x68/0x90
        __mutex_lock+0x98/0x430
        mutex_lock_nested+0x2c/0x40
        ufshcd_query_flag+0x50/0x1c0
        ufshcd_query_flag_retry+0x64/0x100
        ufshcd_wb_toggle+0x5c/0x120
        ufshcd_devfreq_scale+0x2c4/0x380
        ufshcd_devfreq_target+0xf4/0x230
        devfreq_set_target+0x84/0x2f0
        devfreq_update_target+0xc4/0xf0
        devfreq_monitor+0x38/0x1f0
        process_one_work+0x288/0x6c0
        worker_thread+0x74/0x450
        kthread+0x118/0x120
        ret_from_fork+0x10/0x20

 other info that might help us debug this:
  Possible unsafe locking scenario:
        CPU0                    CPU1
        ----                    ----
   lock(&hba->clk_scaling_lock);
                                lock(&hba->dev_cmd.lock);
                                lock(&hba->clk_scaling_lock);
   lock(&hba->dev_cmd.lock);

  *** DEADLOCK ***

Fixes: 0e9d4ca43ba8 ("scsi: ufs: Protect some contexts from unexpected clock scaling")
Cc: stable@vger.kernel.org      # 5.12
Cc: Can Guo <quic_cang@quicinc.com>
Tested-by: Andrew Halaney <ahalaney@redhat.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Link: https://lore.kernel.org/r/20230116161201.16923-1-johan+linaro@kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
(cherry picked from commit b03f7ed9af6e5e66ba6008ded9651738450e6c72)
Change-Id: I58d89f72e77838f54a8659f4e6511d79df920bfa
Bug: 286803489
Bug: 289793003
[ reworked lock to be global to preserve the abi - gregkh ]
Signed-off-by: Greg Kroah-Hartman <gregkh@google.com>
(cherry picked from commit c6d386b8a6c4b9cfaee609fb1a0f291ba70e99f9)
1 file changed
tree: 8fa18a28c1e9c81ddfb48a5661ac44ed9996ecd8
  1. android/
  2. arch/
  3. block/
  4. certs/
  5. crypto/
  6. Documentation/
  7. drivers/
  8. fs/
  9. include/
  10. init/
  11. io_uring/
  12. ipc/
  13. kernel/
  14. lib/
  15. LICENSES/
  16. mm/
  17. net/
  18. samples/
  19. scripts/
  20. security/
  21. sound/
  22. tools/
  23. usr/
  24. virt/
  25. .clang-format
  26. .cocciconfig
  27. .get_maintainer.ignore
  28. .gitattributes
  29. .gitignore
  30. .mailmap
  31. BUILD.bazel
  32. build.config.aarch64
  33. build.config.allmodconfig
  34. build.config.allmodconfig.aarch64
  35. build.config.allmodconfig.arm
  36. build.config.allmodconfig.x86_64
  37. build.config.amlogic
  38. build.config.arm
  39. build.config.common
  40. build.config.constants
  41. build.config.db845c
  42. build.config.gce.x86_64
  43. build.config.gki
  44. build.config.gki-debug.aarch64
  45. build.config.gki-debug.x86_64
  46. build.config.gki.aarch64
  47. build.config.gki.aarch64.fips140
  48. build.config.gki.x86_64
  49. build.config.gki_kasan
  50. build.config.gki_kasan.aarch64
  51. build.config.gki_kasan.x86_64
  52. build.config.gki_kprobes
  53. build.config.gki_kprobes.aarch64
  54. build.config.gki_kprobes.x86_64
  55. build.config.khwasan
  56. build.config.rockpi4
  57. build.config.x86_64
  58. COPYING
  59. CREDITS
  60. Kbuild
  61. Kconfig
  62. Kconfig.ext
  63. MAINTAINERS
  64. Makefile
  65. OWNERS
  66. README
  67. README.md
README.md

How do I submit patches to Android Common Kernels

  1. BEST: Make all of your changes to upstream Linux. If appropriate, backport to the stable releases. These patches will be merged automatically in the corresponding common kernels. If the patch is already in upstream Linux, post a backport of the patch that conforms to the patch requirements below.

    • Do not send patches upstream that contain only symbol exports. To be considered for upstream Linux, additions of EXPORT_SYMBOL_GPL() require an in-tree modular driver that uses the symbol -- so include the new driver or changes to an existing driver in the same patchset as the export.
    • When sending patches upstream, the commit message must contain a clear case for why the patch is needed and beneficial to the community. Enabling out-of-tree drivers or functionality is not not a persuasive case.
  2. LESS GOOD: Develop your patches out-of-tree (from an upstream Linux point-of-view). Unless these are fixing an Android-specific bug, these are very unlikely to be accepted unless they have been coordinated with kernel-team@android.com. If you want to proceed, post a patch that conforms to the patch requirements below.

Common Kernel patch requirements

  • All patches must conform to the Linux kernel coding standards and pass scripts/checkpatch.pl
  • Patches shall not break gki_defconfig or allmodconfig builds for arm, arm64, x86, x86_64 architectures (see https://source.android.com/setup/build/building-kernels)
  • If the patch is not merged from an upstream branch, the subject must be tagged with the type of patch: UPSTREAM:, BACKPORT:, FROMGIT:, FROMLIST:, or ANDROID:.
  • All patches must have a Change-Id: tag (see https://gerrit-review.googlesource.com/Documentation/user-changeid.html)
  • If an Android bug has been assigned, there must be a Bug: tag.
  • All patches must have a Signed-off-by: tag by the author and the submitter

Additional requirements are listed below based on patch type

Requirements for backports from mainline Linux: UPSTREAM:, BACKPORT:

  • If the patch is a cherry-pick from Linux mainline with no changes at all
    • tag the patch subject with UPSTREAM:.
    • add upstream commit information with a (cherry picked from commit ...) line
    • Example:
      • if the upstream commit message is
        important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>
  • then Joe Smith would upload the patch for the common kernel as
        UPSTREAM: important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>

        Bug: 135791357
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        (cherry picked from commit c31e73121f4c1ec41143423ac6ce3ce6dafdcec1)
        Signed-off-by: Joe Smith <joe.smith@foo.org>
  • If the patch requires any changes from the upstream version, tag the patch with BACKPORT: instead of UPSTREAM:.
    • use the same tags as UPSTREAM:
    • add comments about the changes under the (cherry picked from commit ...) line
    • Example:
        BACKPORT: important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>

        Bug: 135791357
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        (cherry picked from commit c31e73121f4c1ec41143423ac6ce3ce6dafdcec1)
        [joe: Resolved minor conflict in drivers/foo/bar.c ]
        Signed-off-by: Joe Smith <joe.smith@foo.org>

Requirements for other backports: FROMGIT:, FROMLIST:,

  • If the patch has been merged into an upstream maintainer tree, but has not yet been merged into Linux mainline
    • tag the patch subject with FROMGIT:
    • add info on where the patch came from as (cherry picked from commit <sha1> <repo> <branch>). This must be a stable maintainer branch (not rebased, so don't use linux-next for example).
    • if changes were required, use BACKPORT: FROMGIT:
    • Example:
      • if the commit message in the maintainer tree is
        important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>
  • then Joe Smith would upload the patch for the common kernel as
        FROMGIT: important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>

        Bug: 135791357
        (cherry picked from commit 878a2fd9de10b03d11d2f622250285c7e63deace
         https://git.kernel.org/pub/scm/linux/kernel/git/foo/bar.git test-branch)
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        Signed-off-by: Joe Smith <joe.smith@foo.org>
  • If the patch has been submitted to LKML, but not accepted into any maintainer tree
    • tag the patch subject with FROMLIST:
    • add a Link: tag with a link to the submittal on lore.kernel.org
    • add a Bug: tag with the Android bug (required for patches not accepted into a maintainer tree)
    • if changes were required, use BACKPORT: FROMLIST:
    • Example:
        FROMLIST: important patch from upstream

        This is the detailed description of the important patch

        Signed-off-by: Fred Jones <fred.jones@foo.org>

        Bug: 135791357
        Link: https://lore.kernel.org/lkml/20190619171517.GA17557@someone.com/
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        Signed-off-by: Joe Smith <joe.smith@foo.org>

Requirements for Android-specific patches: ANDROID:

  • If the patch is fixing a bug to Android-specific code
    • tag the patch subject with ANDROID:
    • add a Fixes: tag that cites the patch with the bug
    • Example:
        ANDROID: fix android-specific bug in foobar.c

        This is the detailed description of the important fix

        Fixes: 1234abcd2468 ("foobar: add cool feature")
        Change-Id: I4caaaa566ea080fa148c5e768bb1a0b6f7201c01
        Signed-off-by: Joe Smith <joe.smith@foo.org>
  • If the patch is a new feature
    • tag the patch subject with ANDROID:
    • add a Bug: tag with the Android bug (required for android-specific features)