bcmdhd-usb.1.201.88.27.x/include/sbsdio.h - kernel/amlogic-tv-modules/dhd-driver - Git at Google

 /*
  * SDIO device core hardware definitions.
  * sdio is a portion of the pcmcia core in core rev 3 - rev 8
  *
  * SDIO core support 1bit, 4 bit SDIO mode as well as SPI mode.
  *
  * Copyright (C) 1999-2015, Broadcom Corporation
  *
  *      Unless you and Broadcom execute a separate written software license
  * agreement governing use of this software, this software is licensed to you
  * under the terms of the GNU General Public License version 2 (the "GPL"),
  * available at http://www.broadcom.com/licenses/GPLv2.php, with the
  * following added to such license:
  *
  *      As a special exception, the copyright holders of this software give you
  * permission to link this software with independent modules, and to copy and
  * distribute the resulting executable under terms of your choice, provided that
  * you also meet, for each linked independent module, the terms and conditions of
  * the license of that module.  An independent module is a module which is not
  * derived from this software.  The special exception does not apply to any
  * modifications of the software.
  *
  *      Notwithstanding the above, under no circumstances may you combine this
  * software in any way with any other Broadcom software provided under a license
  * other than the GPL, without Broadcom's express prior written consent.
  *
  * $Id: sbsdio.h 383835 2013-02-07 23:32:39Z $
  */

 #ifndef	_SBSDIO_H
 #define	_SBSDIO_H

 #define SBSDIO_NUM_FUNCTION		3	/* as of sdiod rev 0, supports 3 functions */

 /* function 1 miscellaneous registers */
 #define SBSDIO_SPROM_CS			0x10000		/* sprom command and status */
 #define SBSDIO_SPROM_INFO		0x10001		/* sprom info register */
 #define SBSDIO_SPROM_DATA_LOW		0x10002		/* sprom indirect access data byte 0 */
 #define SBSDIO_SPROM_DATA_HIGH		0x10003 	/* sprom indirect access data byte 1 */
 #define SBSDIO_SPROM_ADDR_LOW		0x10004		/* sprom indirect access addr byte 0 */
 #define SBSDIO_SPROM_ADDR_HIGH		0x10005		/* sprom indirect access addr byte 0 */
 #define SBSDIO_CHIP_CTRL_DATA		0x10006		/* xtal_pu (gpio) output */
 #define SBSDIO_CHIP_CTRL_EN		0x10007		/* xtal_pu (gpio) enable */
 #define SBSDIO_WATERMARK		0x10008		/* rev < 7, watermark for sdio device */
 #define SBSDIO_DEVICE_CTL		0x10009		/* control busy signal generation */

 /* registers introduced in rev 8, some content (mask/bits) defs in sbsdpcmdev.h */
 #define SBSDIO_FUNC1_SBADDRLOW		0x1000A		/* SB Address Window Low (b15) */
 #define SBSDIO_FUNC1_SBADDRMID		0x1000B		/* SB Address Window Mid (b23:b16) */
 #define SBSDIO_FUNC1_SBADDRHIGH		0x1000C		/* SB Address Window High (b31:b24)    */
 #define SBSDIO_FUNC1_FRAMECTRL		0x1000D		/* Frame Control (frame term/abort) */
 #define SBSDIO_FUNC1_CHIPCLKCSR		0x1000E		/* ChipClockCSR (ALP/HT ctl/status) */
 #define SBSDIO_FUNC1_SDIOPULLUP 	0x1000F		/* SdioPullUp (on cmd, d0-d2) */
 #define SBSDIO_FUNC1_WFRAMEBCLO		0x10019		/* Write Frame Byte Count Low */
 #define SBSDIO_FUNC1_WFRAMEBCHI		0x1001A		/* Write Frame Byte Count High */
 #define SBSDIO_FUNC1_RFRAMEBCLO		0x1001B		/* Read Frame Byte Count Low */
 #define SBSDIO_FUNC1_RFRAMEBCHI		0x1001C		/* Read Frame Byte Count High */
 #define SBSDIO_FUNC1_MESBUSYCTRL	0x1001D		/* MesBusyCtl at 0x1001D (rev 11) */

 #define SBSDIO_FUNC1_MISC_REG_START	0x10000 	/* f1 misc register start */
 #define SBSDIO_FUNC1_MISC_REG_LIMIT	0x1001C 	/* f1 misc register end */

 /* Sdio Core Rev 12 */
 #define SBSDIO_FUNC1_WAKEUPCTRL			0x1001E
 #define SBSDIO_FUNC1_WCTRL_ALPWAIT_MASK		0x1
 #define SBSDIO_FUNC1_WCTRL_ALPWAIT_SHIFT	0
 #define SBSDIO_FUNC1_WCTRL_HTWAIT_MASK		0x2
 #define SBSDIO_FUNC1_WCTRL_HTWAIT_SHIFT		1
 #define SBSDIO_FUNC1_SLEEPCSR			0x1001F
 #define SBSDIO_FUNC1_SLEEPCSR_KSO_MASK		0x1
 #define SBSDIO_FUNC1_SLEEPCSR_KSO_SHIFT		0
 #define SBSDIO_FUNC1_SLEEPCSR_KSO_EN		1
 #define SBSDIO_FUNC1_SLEEPCSR_DEVON_MASK	0x2
 #define SBSDIO_FUNC1_SLEEPCSR_DEVON_SHIFT	1

 /* SBSDIO_SPROM_CS */
 #define SBSDIO_SPROM_IDLE		0
 #define SBSDIO_SPROM_WRITE		1
 #define SBSDIO_SPROM_READ		2
 #define SBSDIO_SPROM_WEN		4
 #define SBSDIO_SPROM_WDS		7
 #define SBSDIO_SPROM_DONE		8

 /* SBSDIO_SPROM_INFO */
 #define SROM_SZ_MASK			0x03		/* SROM size, 1: 4k, 2: 16k */
 #define SROM_BLANK			0x04		/* depreciated in corerev 6 */
 #define	SROM_OTP			0x80		/* OTP present */

 /* SBSDIO_CHIP_CTRL */
 #define SBSDIO_CHIP_CTRL_XTAL		0x01		/* or'd with onchip xtal_pu,
 							 * 1: power on oscillator
 							 * (for 4318 only)
 							 */
 /* SBSDIO_WATERMARK */
 #define SBSDIO_WATERMARK_MASK		0x7f		/* number of words - 1 for sd device
 							 * to wait before sending data to host
 							 */

 /* SBSDIO_MESBUSYCTRL */
 /* When RX FIFO has less entries than this & MBE is set
  * => busy signal is asserted between data blocks.
 */
 #define SBSDIO_MESBUSYCTRL_MASK		0x7f
 #define SBSDIO_MESBUSYCTRL_ENAB		0x80		/* Enable busy capability for MES access */

 /* SBSDIO_DEVICE_CTL */
 #define SBSDIO_DEVCTL_SETBUSY		0x01		/* 1: device will assert busy signal when
 							 * receiving CMD53
 							 */
 #define SBSDIO_DEVCTL_SPI_INTR_SYNC	0x02		/* 1: assertion of sdio interrupt is
 							 * synchronous to the sdio clock
 							 */
 #define SBSDIO_DEVCTL_CA_INT_ONLY	0x04		/* 1: mask all interrupts to host
 							 * except the chipActive (rev 8)
 							 */
 #define SBSDIO_DEVCTL_PADS_ISO		0x08		/* 1: isolate internal sdio signals, put
 							 * external pads in tri-state; requires
 							 * sdio bus power cycle to clear (rev 9)
 							 */
 #define SBSDIO_DEVCTL_EN_F2_BLK_WATERMARK 0x10  /* Enable function 2 tx for each block */
 #define SBSDIO_DEVCTL_F2WM_ENAB		0x10		/* Enable F2 Watermark */
 #define SBSDIO_DEVCTL_NONDAT_PADS_ISO 	0x20		/* Isolate sdio clk and cmd (non-data) */

 /* SBSDIO_FUNC1_CHIPCLKCSR */
 #define SBSDIO_FORCE_ALP		0x01		/* Force ALP request to backplane */
 #define SBSDIO_FORCE_HT			0x02		/* Force HT request to backplane */
 #define SBSDIO_FORCE_ILP		0x04		/* Force ILP request to backplane */
 #define SBSDIO_ALP_AVAIL_REQ		0x08		/* Make ALP ready (power up xtal) */
 #define SBSDIO_HT_AVAIL_REQ		0x10		/* Make HT ready (power up PLL) */
 #define SBSDIO_FORCE_HW_CLKREQ_OFF	0x20		/* Squelch clock requests from HW */
 #define SBSDIO_ALP_AVAIL		0x40		/* Status: ALP is ready */
 #define SBSDIO_HT_AVAIL			0x80		/* Status: HT is ready */
 /* In rev8, actual avail bits followed original docs */
 #define SBSDIO_Rev8_HT_AVAIL		0x40
 #define SBSDIO_Rev8_ALP_AVAIL		0x80
 #define SBSDIO_CSR_MASK			0x1F

 #define SBSDIO_AVBITS			(SBSDIO_HT_AVAIL | SBSDIO_ALP_AVAIL)
 #define SBSDIO_ALPAV(regval)		((regval) & SBSDIO_AVBITS)
 #define SBSDIO_HTAV(regval)		(((regval) & SBSDIO_AVBITS) == SBSDIO_AVBITS)
 #define SBSDIO_ALPONLY(regval)		(SBSDIO_ALPAV(regval) && !SBSDIO_HTAV(regval))
 #define SBSDIO_CLKAV(regval, alponly)	(SBSDIO_ALPAV(regval) && \
 					(alponly ? 1 : SBSDIO_HTAV(regval)))

 /* SBSDIO_FUNC1_SDIOPULLUP */
 #define SBSDIO_PULLUP_D0		0x01		/* Enable D0/MISO pullup */
 #define SBSDIO_PULLUP_D1		0x02		/* Enable D1/INT# pullup */
 #define SBSDIO_PULLUP_D2		0x04		/* Enable D2 pullup */
 #define SBSDIO_PULLUP_CMD		0x08		/* Enable CMD/MOSI pullup */
 #define SBSDIO_PULLUP_ALL		0x0f		/* All valid bits */

 /* function 1 OCP space */
 #define SBSDIO_SB_OFT_ADDR_MASK		0x07FFF		/* sb offset addr is <= 15 bits, 32k */
 #define SBSDIO_SB_OFT_ADDR_LIMIT	0x08000
 #define SBSDIO_SB_ACCESS_2_4B_FLAG	0x08000		/* with b15, maps to 32-bit SB access */

 /* some duplication with sbsdpcmdev.h here */
 /* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */
 #define SBSDIO_SBADDRLOW_MASK		0x80		/* Valid bits in SBADDRLOW */
 #define SBSDIO_SBADDRMID_MASK		0xff		/* Valid bits in SBADDRMID */
 #define SBSDIO_SBADDRHIGH_MASK		0xffU		/* Valid bits in SBADDRHIGH */
 #define SBSDIO_SBWINDOW_MASK		0xffff8000	/* Address bits from SBADDR regs */

 /* direct(mapped) cis space */
 #define SBSDIO_CIS_BASE_COMMON		0x1000		/* MAPPED common CIS address */
 #define SBSDIO_CIS_SIZE_LIMIT		0x200		/* maximum bytes in one CIS */
 #define SBSDIO_OTP_CIS_SIZE_LIMIT       0x078           /* maximum bytes OTP CIS */

 #define SBSDIO_CIS_OFT_ADDR_MASK	0x1FFFF		/* cis offset addr is < 17 bits */

 #define SBSDIO_CIS_MANFID_TUPLE_LEN	6		/* manfid tuple length, include tuple,
 							 * link bytes
 							 */

 /* indirect cis access (in sprom) */
 #define SBSDIO_SPROM_CIS_OFFSET		0x8		/* 8 control bytes first, CIS starts from
 							 * 8th byte
 							 */

 #define SBSDIO_BYTEMODE_DATALEN_MAX	64		/* sdio byte mode: maximum length of one
 							 * data comamnd
 							 */

 #define SBSDIO_CORE_ADDR_MASK		0x1FFFF		/* sdio core function one address mask */

 #endif	/* _SBSDIO_H */
	/*
	* SDIO device core hardware definitions.
	* sdio is a portion of the pcmcia core in core rev 3 - rev 8
	*
	* SDIO core support 1bit, 4 bit SDIO mode as well as SPI mode.
	*
	* Copyright (C) 1999-2015, Broadcom Corporation
	*
	* Unless you and Broadcom execute a separate written software license
	* agreement governing use of this software, this software is licensed to you
	* under the terms of the GNU General Public License version 2 (the "GPL"),
	* available at http://www.broadcom.com/licenses/GPLv2.php, with the
	* following added to such license:
	*
	* As a special exception, the copyright holders of this software give you
	* permission to link this software with independent modules, and to copy and
	* distribute the resulting executable under terms of your choice, provided that
	* you also meet, for each linked independent module, the terms and conditions of
	* the license of that module. An independent module is a module which is not
	* derived from this software. The special exception does not apply to any
	* modifications of the software.
	*
	* Notwithstanding the above, under no circumstances may you combine this
	* software in any way with any other Broadcom software provided under a license
	* other than the GPL, without Broadcom's express prior written consent.
	*
	* $Id: sbsdio.h 383835 2013-02-07 23:32:39Z $
	*/

	#ifndef _SBSDIO_H
	#define _SBSDIO_H

	#define SBSDIO_NUM_FUNCTION 3 /* as of sdiod rev 0, supports 3 functions */

	/* function 1 miscellaneous registers */
	#define SBSDIO_SPROM_CS 0x10000 /* sprom command and status */
	#define SBSDIO_SPROM_INFO 0x10001 /* sprom info register */
	#define SBSDIO_SPROM_DATA_LOW 0x10002 /* sprom indirect access data byte 0 */
	#define SBSDIO_SPROM_DATA_HIGH 0x10003 /* sprom indirect access data byte 1 */
	#define SBSDIO_SPROM_ADDR_LOW 0x10004 /* sprom indirect access addr byte 0 */
	#define SBSDIO_SPROM_ADDR_HIGH 0x10005 /* sprom indirect access addr byte 0 */
	#define SBSDIO_CHIP_CTRL_DATA 0x10006 /* xtal_pu (gpio) output */
	#define SBSDIO_CHIP_CTRL_EN 0x10007 /* xtal_pu (gpio) enable */
	#define SBSDIO_WATERMARK 0x10008 /* rev < 7, watermark for sdio device */
	#define SBSDIO_DEVICE_CTL 0x10009 /* control busy signal generation */

	/* registers introduced in rev 8, some content (mask/bits) defs in sbsdpcmdev.h */
	#define SBSDIO_FUNC1_SBADDRLOW 0x1000A /* SB Address Window Low (b15) */
	#define SBSDIO_FUNC1_SBADDRMID 0x1000B /* SB Address Window Mid (b23:b16) */
	#define SBSDIO_FUNC1_SBADDRHIGH 0x1000C /* SB Address Window High (b31:b24) */
	#define SBSDIO_FUNC1_FRAMECTRL 0x1000D /* Frame Control (frame term/abort) */
	#define SBSDIO_FUNC1_CHIPCLKCSR 0x1000E /* ChipClockCSR (ALP/HT ctl/status) */
	#define SBSDIO_FUNC1_SDIOPULLUP 0x1000F /* SdioPullUp (on cmd, d0-d2) */
	#define SBSDIO_FUNC1_WFRAMEBCLO 0x10019 /* Write Frame Byte Count Low */
	#define SBSDIO_FUNC1_WFRAMEBCHI 0x1001A /* Write Frame Byte Count High */
	#define SBSDIO_FUNC1_RFRAMEBCLO 0x1001B /* Read Frame Byte Count Low */
	#define SBSDIO_FUNC1_RFRAMEBCHI 0x1001C /* Read Frame Byte Count High */
	#define SBSDIO_FUNC1_MESBUSYCTRL 0x1001D /* MesBusyCtl at 0x1001D (rev 11) */

	#define SBSDIO_FUNC1_MISC_REG_START 0x10000 /* f1 misc register start */
	#define SBSDIO_FUNC1_MISC_REG_LIMIT 0x1001C /* f1 misc register end */

	/* Sdio Core Rev 12 */
	#define SBSDIO_FUNC1_WAKEUPCTRL 0x1001E
	#define SBSDIO_FUNC1_WCTRL_ALPWAIT_MASK 0x1
	#define SBSDIO_FUNC1_WCTRL_ALPWAIT_SHIFT 0
	#define SBSDIO_FUNC1_WCTRL_HTWAIT_MASK 0x2
	#define SBSDIO_FUNC1_WCTRL_HTWAIT_SHIFT 1
	#define SBSDIO_FUNC1_SLEEPCSR 0x1001F
	#define SBSDIO_FUNC1_SLEEPCSR_KSO_MASK 0x1
	#define SBSDIO_FUNC1_SLEEPCSR_KSO_SHIFT 0
	#define SBSDIO_FUNC1_SLEEPCSR_KSO_EN 1
	#define SBSDIO_FUNC1_SLEEPCSR_DEVON_MASK 0x2
	#define SBSDIO_FUNC1_SLEEPCSR_DEVON_SHIFT 1

	/* SBSDIO_SPROM_CS */
	#define SBSDIO_SPROM_IDLE 0
	#define SBSDIO_SPROM_WRITE 1
	#define SBSDIO_SPROM_READ 2
	#define SBSDIO_SPROM_WEN 4
	#define SBSDIO_SPROM_WDS 7
	#define SBSDIO_SPROM_DONE 8

	/* SBSDIO_SPROM_INFO */
	#define SROM_SZ_MASK 0x03 /* SROM size, 1: 4k, 2: 16k */
	#define SROM_BLANK 0x04 /* depreciated in corerev 6 */
	#define SROM_OTP 0x80 /* OTP present */

	/* SBSDIO_CHIP_CTRL */
	#define SBSDIO_CHIP_CTRL_XTAL 0x01 /* or'd with onchip xtal_pu,
	* 1: power on oscillator
	* (for 4318 only)
	*/
	/* SBSDIO_WATERMARK */
	#define SBSDIO_WATERMARK_MASK 0x7f /* number of words - 1 for sd device
	* to wait before sending data to host
	*/

	/* SBSDIO_MESBUSYCTRL */
	/* When RX FIFO has less entries than this & MBE is set
	* => busy signal is asserted between data blocks.
	*/
	#define SBSDIO_MESBUSYCTRL_MASK 0x7f
	#define SBSDIO_MESBUSYCTRL_ENAB 0x80 /* Enable busy capability for MES access */

	/* SBSDIO_DEVICE_CTL */
	#define SBSDIO_DEVCTL_SETBUSY 0x01 /* 1: device will assert busy signal when
	* receiving CMD53
	*/
	#define SBSDIO_DEVCTL_SPI_INTR_SYNC 0x02 /* 1: assertion of sdio interrupt is
	* synchronous to the sdio clock
	*/
	#define SBSDIO_DEVCTL_CA_INT_ONLY 0x04 /* 1: mask all interrupts to host
	* except the chipActive (rev 8)
	*/
	#define SBSDIO_DEVCTL_PADS_ISO 0x08 /* 1: isolate internal sdio signals, put
	* external pads in tri-state; requires
	* sdio bus power cycle to clear (rev 9)
	*/
	#define SBSDIO_DEVCTL_EN_F2_BLK_WATERMARK 0x10 /* Enable function 2 tx for each block */
	#define SBSDIO_DEVCTL_F2WM_ENAB 0x10 /* Enable F2 Watermark */
	#define SBSDIO_DEVCTL_NONDAT_PADS_ISO 0x20 /* Isolate sdio clk and cmd (non-data) */

	/* SBSDIO_FUNC1_CHIPCLKCSR */
	#define SBSDIO_FORCE_ALP 0x01 /* Force ALP request to backplane */
	#define SBSDIO_FORCE_HT 0x02 /* Force HT request to backplane */
	#define SBSDIO_FORCE_ILP 0x04 /* Force ILP request to backplane */
	#define SBSDIO_ALP_AVAIL_REQ 0x08 /* Make ALP ready (power up xtal) */
	#define SBSDIO_HT_AVAIL_REQ 0x10 /* Make HT ready (power up PLL) */
	#define SBSDIO_FORCE_HW_CLKREQ_OFF 0x20 /* Squelch clock requests from HW */
	#define SBSDIO_ALP_AVAIL 0x40 /* Status: ALP is ready */
	#define SBSDIO_HT_AVAIL 0x80 /* Status: HT is ready */
	/* In rev8, actual avail bits followed original docs */
	#define SBSDIO_Rev8_HT_AVAIL 0x40
	#define SBSDIO_Rev8_ALP_AVAIL 0x80
	#define SBSDIO_CSR_MASK 0x1F

	#define SBSDIO_AVBITS (SBSDIO_HT_AVAIL \| SBSDIO_ALP_AVAIL)
	#define SBSDIO_ALPAV(regval) ((regval) & SBSDIO_AVBITS)
	#define SBSDIO_HTAV(regval) (((regval) & SBSDIO_AVBITS) == SBSDIO_AVBITS)
	#define SBSDIO_ALPONLY(regval) (SBSDIO_ALPAV(regval) && !SBSDIO_HTAV(regval))
	#define SBSDIO_CLKAV(regval, alponly) (SBSDIO_ALPAV(regval) && \
	(alponly ? 1 : SBSDIO_HTAV(regval)))

	/* SBSDIO_FUNC1_SDIOPULLUP */
	#define SBSDIO_PULLUP_D0 0x01 /* Enable D0/MISO pullup */
	#define SBSDIO_PULLUP_D1 0x02 /* Enable D1/INT# pullup */
	#define SBSDIO_PULLUP_D2 0x04 /* Enable D2 pullup */
	#define SBSDIO_PULLUP_CMD 0x08 /* Enable CMD/MOSI pullup */
	#define SBSDIO_PULLUP_ALL 0x0f /* All valid bits */

	/* function 1 OCP space */
	#define SBSDIO_SB_OFT_ADDR_MASK 0x07FFF /* sb offset addr is <= 15 bits, 32k */
	#define SBSDIO_SB_OFT_ADDR_LIMIT 0x08000
	#define SBSDIO_SB_ACCESS_2_4B_FLAG 0x08000 /* with b15, maps to 32-bit SB access */

	/* some duplication with sbsdpcmdev.h here */
	/* valid bits in SBSDIO_FUNC1_SBADDRxxx regs */
	#define SBSDIO_SBADDRLOW_MASK 0x80 /* Valid bits in SBADDRLOW */
	#define SBSDIO_SBADDRMID_MASK 0xff /* Valid bits in SBADDRMID */
	#define SBSDIO_SBADDRHIGH_MASK 0xffU /* Valid bits in SBADDRHIGH */
	#define SBSDIO_SBWINDOW_MASK 0xffff8000 /* Address bits from SBADDR regs */

	/* direct(mapped) cis space */
	#define SBSDIO_CIS_BASE_COMMON 0x1000 /* MAPPED common CIS address */
	#define SBSDIO_CIS_SIZE_LIMIT 0x200 /* maximum bytes in one CIS */
	#define SBSDIO_OTP_CIS_SIZE_LIMIT 0x078 /* maximum bytes OTP CIS */

	#define SBSDIO_CIS_OFT_ADDR_MASK 0x1FFFF /* cis offset addr is < 17 bits */

	#define SBSDIO_CIS_MANFID_TUPLE_LEN 6 /* manfid tuple length, include tuple,
	* link bytes
	*/

	/* indirect cis access (in sprom) */
	#define SBSDIO_SPROM_CIS_OFFSET 0x8 /* 8 control bytes first, CIS starts from
	* 8th byte
	*/

	#define SBSDIO_BYTEMODE_DATALEN_MAX 64 /* sdio byte mode: maximum length of one
	* data comamnd
	*/

	#define SBSDIO_CORE_ADDR_MASK 0x1FFFF /* sdio core function one address mask */

	#endif /* _SBSDIO_H */