blob: 5c9e7d614cccd95ee17db0e76689ad95073ddd4a [file] [log] [blame]
#Version check for XTRA
#DISABLE = 0
#AUTO = 1
#XTRA2 = 2
#XTRA3 = 3
XTRA_VERSION_CHECK=0
# Error Estimate
# _SET = 1
# _CLEAR = 0
ERR_ESTIMATE=0
#NTP server
NTP_SERVER = time.google.com
#XTRA CA path
XTRA_CA_PATH=/usr/lib/ssl-1.1/certs
# DEBUG LEVELS: 0 - none, 1 - Error, 2 - Warning, 3 - Info
# 4 - Debug, 5 - Verbose
# If DEBUG_LEVEL is commented, Android's logging levels will be used
DEBUG_LEVEL = 2
# Intermediate position report, 1=enable, 0=disable
INTERMEDIATE_POS=0
# Below bit mask configures how GPS functionalities
# should be locked when user turns off GPS on Settings
# Set bit 0x1 if MO GPS functionalities are to be locked
# Set bit 0x2 if NI GPS functionalities are to be locked
# default – both MO and NI locked for maximal privacy
#GPS_LOCK = 3
# supl version 1.0
#SUPL_VER=0x10000
# Emergency SUPL, 1=enable, 0=disable
SUPL_ES=1
#Choose PDN for Emergency SUPL
#1 - Use emergency PDN
#0 - Use regular SUPL PDN for Emergency SUPL
#USE_EMERGENCY_PDN_FOR_EMERGENCY_SUPL=0
#SUPL_MODE is a bit mask set in config.xml per carrier by default.
#If it is uncommented here, this value will overwrite the value from
#config.xml.
#MSA=0X2
#MSB=0X1
#SUPL_MODE=
# GPS Capabilities bit mask
# SCHEDULING = 0x01
# MSB = 0x02
# MSA = 0x04
# ON_DEMAND_TIME = 0x10
# default = ON_DEMAND_TIME | MSA | MSB | SCHEDULING
CAPABILITIES=0x17
# Accuracy threshold for intermediate positions
# less accurate positions are ignored, 0 for passing all positions
# ACCURACY_THRES=5000
################################
##### AGPS server settings #####
################################
# FOR SUPL SUPPORT, set the following
# SUPL_HOST=supl.host.com or IP
# SUPL_PORT=1234
# FOR MO SUPL SUPPORT, set the following
# MO_SUPL_HOST=supl.host.com or IP
# MO_SUPL_PORT=1234
# FOR C2K PDE SUPPORT, set the following
# C2K_HOST=c2k.pde.com or IP
# C2K_PORT=1234
# Bitmask of slots that are available
# for write/install to, where 1s indicate writable,
# and the default value is 0 where no slots
# are writable. For example, AGPS_CERT_WRITABLE_MASK
# of b1000001010 makes 3 slots available
# and the remaining 7 slots unwritable.
#AGPS_CERT_WRITABLE_MASK=0
####################################
# LTE Positioning Profile Settings
####################################
# 0: Enable RRLP on LTE(Default)
# 1: Enable LPP_User_Plane on LTE
# 2: Enable LPP_Control_Plane
# 3: Enable both LPP_User_Plane and LPP_Control_Plane
#LPP_PROFILE = 2
####################################
#Datum Type
####################################
# 0: WGS-84
# 1: PZ-90
DATUM_TYPE = 0
################################
# EXTRA SETTINGS
################################
# NMEA provider (1=Modem Processor, 0=Application Processor)
NMEA_PROVIDER=0
# Mark if it is a SGLTE target (1=SGLTE, 0=nonSGLTE)
SGLTE_TARGET=0
##################################################
# Select Positioning Protocol on A-GLONASS system
##################################################
# 0x1: RRC CPlane
# 0x2: RRLP UPlane
# 0x4: LLP Uplane
#A_GLONASS_POS_PROTOCOL_SELECT = 0
##################################################
# Select technology for LPPe Control Plane
##################################################
# 0x1: DBH for LPPe CP
# 0x2: WLAN AP Measurements for LPPe CP
# 0x4: SRN AP measurement for CP
# 0x8: Sensor Barometer Measurement LPPe CP
#LPPE_CP_TECHNOLOGY = 0
##################################################
# Select technology for LPPe User Plane
##################################################
# 0x1: DBH for LPPe UP
# 0x2: WLAN AP Measurements for LPPe UP
# 0x4: SRN AP measurement for UP
# 0x8: Sensor Barometer Measurement LPPe UP
#LPPE_UP_TECHNOLOGY = 0
##################################################
# AGPS_CONFIG_INJECT
##################################################
# enable/disable injection of AGPS configurations:
# SUPL_VER
# SUPL_HOST
# SUPL_PORT
# MO_SUPL_HOST
# MO_SUPL_PORT
# C2K_HOST
# C2K_PORT
# LPP_PROFILE
# A_GLONASS_POS_PROTOCOL_SELECT
# 0: disable
# 1: enable
AGPS_CONFIG_INJECT = 1
##################################################
# GNSS settings for automotive use cases
# Configurations in following section are
# specific to automotive use cases, others
# please do not change, keep the default values
##################################################
# AP Coarse Timestamp Uncertainty
##################################################
# default : 10
# AP time stamp uncertainty, until GNSS receiver
# is able to acquire better timing information
AP_TIMESTAMP_UNCERTAINTY = 10
##################################################
# QDR engine availability status
##################################################
# 0 : NO QDR (default)
# 1 : QDR enabled
# This settings enables QDR Configuration for
# automotive use case, if enabled then
# DR_AP_Service needs to be enabled in izat.conf
#EXTERNAL_DR_ENABLED = 0
#####################################
# DR_SYNC Pulse Availability
#####################################
# 0 : DR_SYNC pulse not available (default)
# 1 : DR_SYNC pulse available
# This configuration enables the driver to make use
# of PPS events generated by DR_SYNC pulse
# Standard Linux PPS driver needs to be enabled
DR_SYNC_ENABLED = 0
#####################################
# PPS Device name
#####################################
PPS_DEVICENAME = /dev/pps0
#####################################
# Ignore PPS at Startup and after long outage
#####################################
IGNORE_PPS_PULSE_COUNT = 1
#####################################
# Long GNSS RF outage in seconds
#####################################
GNSS_OUTAGE_DURATION = 10
#####################################
# AP Clock Accuracy
#####################################
# Quality of APPS processor clock (in PPM).
# Value specified is used for calculation of
# APPS time stamp uncertainty
AP_CLOCK_PPM = 100
#####################################
# MAX ms difference to detect missing pulse
#####################################
# Specifies time threshold in ms to validate any missing PPS pulses
MISSING_PULSE_TIME_DELTA = 900
#####################################
# Propagation time uncertainty
#####################################
# This settings enables time uncertainty propagation
# logic incase of missing PPS pulse
PROPAGATION_TIME_UNCERTAINTY = 1
#######################################
# APN / IP Type Configuration
# APN and IP Type to use for setting
# up WWAN call.
# Use below values for IP Type:
# v4 = 4
# v6 = 6
# v4v6 = 10
#######################################
# INTERNET_APN = abc.xyz
# INTERNET_IP_TYPE = 4
# SUPL_APN = abc.xyz
# SUPL_IP_TYPE = 4
#####################################
# Modem type
#####################################
# This setting configures modem type
# (external=0 or internal=1)
# comment out the next line to vote
# for the first modem in the list
MODEM_TYPE = 1
##################################################
# CONSTRAINED TIME UNCERTAINTY MODE
##################################################
# 0 : disabled (default)
# 1 : enabled
# This setting enables GPS engine to keep its time
# uncertainty below the specified constraint
#CONSTRAINED_TIME_UNCERTAINTY_ENABLED = 0
# If constrained time uncertainty mode is enabled,
# this setting specifies the time uncertainty
# threshold that gps engine need to maintain.
# In unit of milli-seconds.
# Default is 0.0 meaning that modem default value
# of time uncertainty threshold will be used.
#CONSTRAINED_TIME_UNCERTAINTY_THRESHOLD = 0.0
# If constrained time uncertainty mode is enabled,
# this setting specifies the power budget that
# gps engine is allowed to spend to maintain the time
# uncertainty.
# Default is 0 meaning that GPS engine is not constained
# by power budget and can spend as much power as needed.
# In unit of 0.1 milli watt second.
#CONSTRAINED_TIME_UNCERTAINTY_ENERGY_BUDGET = 0
##################################################
# POSITION ASSISTED CLOCK ESTIMATOR
##################################################
# 0 : disabled (default)
# 1 : enabled
# This setting enables GPS engine to estimate clock
# bias and drift when the signal from at least 1
# SV is available and the UE’s position is known by
# other position engines.
#POSITION_ASSISTED_CLOCK_ESTIMATOR_ENABLED = 0
#####################################
# proxyAppPackageName
#####################################
# This is a string that is sent to the framework
# in nfwNotifyCb callback
PROXY_APP_PACKAGE_NAME = com.google.android.carrierlocation
#####################################
# CP_MTLR_ES
#####################################
# CP MTLR ES, 1=enable, 0=disable
CP_MTLR_ES=1
##################################################
# GNSS_DEPLOYMENT
##################################################
# 0 : Enable QTI GNSS (default)
# 1 : Enable QCSR SS5
# This setting use to select between QTI GNSS
# and QCSR SS5 hardware receiver.
# By default QTI GNSS receiver is enabled.
# GNSS_DEPLOYMENT = 0