| # This file allows user to override the factory |
| |
| ############################################# |
| # STA related general configurations |
| ############################################# |
| # Assigned MAC Addresses - This will be used until NV items are in place |
| # Each byte of MAC address is represented in Hex format as XX |
| Intf0MacAddress=000AF58989FF |
| Intf1MacAddress=000AF58989FE |
| Intf2MacAddress=000AF58989FD |
| Intf3MacAddress=000AF58989FC |
| |
| #Channel Bonding |
| gChannelBondingMode5GHz=1 |
| gChannelBondingMode24GHz=0 |
| |
| #Enable Keep alive with non-zero period value |
| gStaKeepAlivePeriod = 30 |
| |
| # Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) |
| gVhtMpduLen=2 |
| |
| # 0 for OLPC 1 for CLPC and SCPC |
| gEnableCloseLoop=1 |
| |
| ImplicitQosIsEnabled=0 |
| |
| # VHT Tx/Rx MCS values |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gVhtRxMCS=2 |
| gVhtTxMCS=2 |
| |
| # VHT Tx/Rx MCS values for 2x2 |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gEnable2x2=1 |
| gVhtRxMCS2x2=2 |
| gVhtTxMCS2x2=2 |
| |
| # Enable Tx beamforming in VHT20MHz |
| # Valid values are 0,1. If commented out, the default value is 0. |
| # 0=disable, 1=enable |
| gEnableTxBFin20MHz=1 |
| |
| # 1=enable tx STBC; 0=disable |
| gEnableTXSTBC=1 |
| |
| # 1=enable STBC; 0=disable STBC |
| gEnableRXSTBC=1 |
| |
| # 1=enable rx LDPC; 0=disable |
| gEnableRXLDPC=1 |
| |
| # Flag to allow STA send AddTspec even when ACM is Off |
| gAddTSWhenACMIsOff=1 |
| |
| # RTS threshold |
| RTSThreshold=1048576 |
| |
| # 802.11d support |
| g11dSupportEnabled=0 |
| |
| |
| # Phy Mode (auto, b, g, n, etc) |
| # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only |
| # 7 = 11b only 8 = 11ac only. |
| gDot11Mode=0 |
| |
| # RX packet handling options |
| # 0: no rx thread, no RPS, for MDM |
| # 1: RX thread |
| # 2: RPS |
| rxhandle=1 |
| |
| #Enable VHT on 2.4Ghz |
| gEnableVhtFor24GHzBand=1 |
| |
| # Regulatory Setting; 0=STRICT; 1=CUSTOM |
| gRegulatoryChangeCountry=1 |
| |
| # Enable/Disable RX full reorder offload |
| gReorderOffloadSupported=1 |
| |
| # userspace country code setting shld take priority |
| gCountryCodePriority=1 |
| |
| # Enable/Disable LPASS support |
| # 0 to disable, 1 to enable |
| gEnableLpassSupport=1 |
| |
| # Enable(1)/Disable(0) SIFS burst |
| gEnableSifsBurst=1 |
| |
| # Tx Chain Mask for CCK |
| gCckChainMaskEnable=1 |
| |
| # Tx Chain Mask for 1SS |
| gTxChainMask1ss=0 |
| |
| # TPC power |
| gSelfGenFrmPwr=3 |
| |
| # Enable or Disable NAN |
| # 1=Enable (default), 0=Disable |
| gEnableNanSupport=1 |
| |
| gIgnorePeerHTopMode=1 |
| gIgnorePeerErpInfo=1 |
| |
| # 802.11n Protection flag |
| gEnableApProt=1 |
| |
| # Fixed Rate |
| gFixedRate=0 |
| |
| # Intra-BSS forward |
| gDisableIntraBssFwd=0 |
| |
| # WMM Enable/Disable |
| WmmIsEnabled=0 |
| |
| # 802.11h support |
| g11hSupportEnabled=1 |
| |
| #Short Guard Interval Enable/disable |
| gShortGI20Mhz=1 |
| gShortGI40Mhz=1 |
| |
| #Auto Shutdown wlan : Value in Seconds. 0 means disabled. Max 1 day = 86400 sec |
| gWlanAutoShutdown=0 |
| |
| #Preferred band (both or 2.4 only or 5 only) |
| BandCapability=0 |
| |
| gVhtChannelWidth=2 |
| |
| # Enable Tx beamforming |
| gTxBFEnable=1 |
| |
| # Set txchainmask and rxchainmask |
| # These parameters are used only if gEnable2x2 is 0 |
| # Valid values are 1,2 |
| # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. |
| # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. |
| gSetTxChainmask1x1=1 |
| gSetRxChainmask1x1=1 |
| |
| #If set to 0, MCC is not allowed. |
| gEnableMCCMode=1 |
| |
| # MCC to SCC Switch mode: 0-Disable 1-Enable 2-Force SCC if same band |
| gWlanMccToSccSwitchMode = 0 |
| |
| # Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) |
| gVhtAmpduLenExponent=7 |
| |
| # Bus bandwidth threshold values in terms of number of packets |
| gBusBandwidthHighThreshold=2000 |
| gBusBandwidthMediumThreshold=500 |
| gBusBandwidthLowThreshold=150 |
| |
| # Bus bandwidth compute timeout value in ms |
| gBusBandwidthComputeInterval=100 |
| |
| # Maximum number of concurrent connections |
| gMaxConcurrentActiveSessions=2 |
| |
| # Radar PRI multiplier |
| gDFSradarMappingPriMultiplier=4 |
| |
| # Enable or Disable Multi-user MIMO |
| # 1=Enable (default), 0=Disable |
| gEnableMuBformee=1 |
| |
| # Enable to check FW hash if secure FW feature is enabled. It's for defconfig |
| # builds only since it will be ignored in performance/release builds. |
| gEnableFWHashCheck=1 |
| |
| # Enable or Disable MCC Adaptive Scheduler at the FW |
| # 1=Enable (default), 0=Disable |
| gEnableMCCAdaptiveScheduler=1 |
| |
| ############################################# |
| # SCAN related configurations |
| ############################################# |
| # Enable/Disable Idle Scan |
| gEnableIdleScan=0 |
| |
| #Enable Scan Results Aging based on timer |
| #Timer value is in seconds |
| #If Set to 0 it will not enable the feature |
| gScanAgingTime=0 |
| |
| #Enable Scan Results Aging based on number of scans |
| gScanResultAgeCount=1 |
| |
| #Enable thermal mitigation |
| gThermalMitigationEnable=0 |
| |
| #List of Country codes for which 11ac needs to be disabled |
| #Each country code must be delimited by comma(,) |
| gListOfNon11acCountryCode=RU,UA,ZA |
| |
| #Maximum Channel time in msec |
| gMaxMediumTime=6000 |
| |
| # Scan Timing Parameters |
| # gPassiveMaxChannelTime=110 |
| # gPassiveMinChannelTime=60 |
| gActiveMaxChannelTime=40 |
| gActiveMinChannelTime=20 |
| |
| gPNOScanSupport=1 |
| |
| # Perform PNO fast scan this many number of times |
| gPNOScanTimerRepeatValue=6 |
| |
| # PNO slow scan period = gPNOSlowScanMultiplier times PNO fast scan period |
| # Example: fast scan period is passed from framework (default = 10 sec), then |
| # PNO slow scan period = 60 sec. |
| gPNOSlowScanMultiplier=6 |
| |
| # Enable or Disable Extended Scan (GScan) |
| # 1=Enable (default), 0=Disable |
| gExtScanEnable=1 |
| |
| #If set will start with active scan after driver load, otherwise will start with |
| #passive scan to find out the domain |
| gEnableBypass11d=1 |
| |
| #If set to 0, will not scan DFS channels |
| gEnableDFSChnlScan=1 |
| |
| gInformBssRssiRaw=0 |
| |
| # Enable or disable Probe Req Information Element whitelist. When enabled, IEs corresponding to bits |
| # set in bitmaps are allowed in probe request, all others removed while device is unassociated |
| # with an AP |
| # 1=Enable, 0=Disable (default) |
| g_enable_probereq_whitelist_ies=1 |
| |
| # ie bitmap examples: <bitmap_name>=<value> [<Allowed Information elements>] |
| # g_probe_req_ie_bitmap_0=0x80000009 #[0, 3, 31] |
| # g_probe_req_ie_bitmap_0=0x00000000 #[] (default) |
| # g_probe_req_ie_bitmap_1=0x80000009 #[32, 35, 63] |
| g_probe_req_ie_bitmap_0=0x0000000B |
| # g_probe_req_ie_bitmap_1=0x00000000 |
| # g_probe_req_ie_bitmap_2=0x00000000 |
| # g_probe_req_ie_bitmap_3=0x00000000 |
| # g_probe_req_ie_bitmap_4=0x00000000 |
| # g_probe_req_ie_bitmap_5=0x00000000 |
| # g_probe_req_ie_bitmap_6=0x00000000 |
| # g_probe_req_ie_bitmap_7=0x00000000 |
| |
| ############################################# |
| # Power related configurations |
| ############################################# |
| # Enable IMPS or not |
| gEnableImps=1 |
| |
| # Enable BMPS or not |
| gEnableBmps=1 |
| |
| # Increase sleep duration (seconds) during IMPS |
| # 0 implies no periodic wake up from IMPS. Periodic wakeup is |
| # unnecessary if Idle Scan is disabled. |
| gImpsModSleepTime=0 |
| |
| # UAPSD service interval for VO,VI, BE, BK traffic |
| InfraUapsdVoSrvIntv=0 |
| InfraUapsdViSrvIntv=0 |
| InfraUapsdBeSrvIntv=0 |
| InfraUapsdBkSrvIntv=0 |
| |
| # Enable suspend or not |
| # 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter |
| gEnableSuspend=3 |
| |
| #Enable Power Save offload |
| gEnablePowerSaveOffload=5 |
| |
| # Enable Runtime PM Feature. |
| # Enabling this feature will put target wow and shutdown pcie link |
| # when inactivity is detected in WLAN Driver. |
| # This feature is inactive when beaconing interfaces are active with |
| # clients associated. |
| # 0 - disable |
| # 1 - enable |
| gRuntimePM=1 |
| |
| # When gRuntimePM is disabled gRuntimeAutoTime won't take effect. |
| # The Time is in msec. |
| # 100 is min, 10000 is max, 500 is default. |
| gRuntimePMDelay=500 |
| |
| #Enable Power saving mechanism Based on Android Framework |
| #If set to 0 Driver internally control the Power saving mechanism |
| #If set to 1 Android Framwrok control the Power saving mechanism |
| isAndroidPsEn=0 |
| |
| #Beacon Early Termination (1 = enable the BET feature, 0 = disable) |
| enableBeaconEarlyTermination=1 |
| |
| beaconEarlyTerminationWakeInterval=3 |
| |
| #Data Inactivity Timeout when in powersave (in ms) |
| gDataInactivityTimeout=200 |
| |
| #Enable or Disable 5G early beacon termination |
| gEnable5gEBT=1 |
| |
| # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode |
| gIbssTxSpEndInactivityTime=10 |
| |
| gEnableModulatedDTIM=2 |
| gMaxLIModulatedDTIM=6 |
| |
| ############################################# |
| # Roaming related configurations |
| ############################################# |
| # CSR Roaming Enable(1) Disable(0) |
| gRoamingTime=0 |
| |
| # ESE Support and fast transition |
| EseEnabled=1 |
| |
| gNeighborLookupThreshold=76 |
| gNeighborReassocThreshold=81 |
| gNeighborScanTimerPeriod=200 |
| gNeighborScanChannelMinTime=20 |
| gNeighborScanChannelMaxTime=30 |
| gMaxNeighborReqTries=3 |
| |
| # To enable, set gRoamIntraBand=1 (Roaming within band) |
| # To disable, set gRoamIntraBand=0 (Roaming across band) |
| gRoamIntraBand=0 |
| |
| # Legacy (non-ESE, non-802.11r) Fast Roaming Support |
| # To enable, set FastRoamEnabled=1 |
| # To disable, set FastRoamEnabled=0 |
| FastRoamEnabled=1 |
| |
| #Check if the AP to which we are roaming is better than current AP in terms of RSSI. |
| #Checking is disabled if set to Zero.Otherwise it will use this value as to how better |
| #the RSSI of the new/roamable AP should be for roaming |
| RoamRssiDiff=3 |
| |
| # If the RSSI of any available candidate is better than currently associated |
| # AP by at least gImmediateRoamRssiDiff, then being to roam immediately (without |
| # registering for reassoc threshold). |
| # NOTE: Value of 0 means that we would register for reassoc threshold. |
| gImmediateRoamRssiDiff=10 |
| |
| # 802.11K support |
| gRrmEnable=1 |
| gRrmOperChanMax=8 |
| gRrmNonOperChanMax=8 |
| |
| gEnableFastRoamInConcurrency=1 |
| |
| # Enable/Disable Roaming Offload Support (a.k.a Key Management Offload) |
| # 0 to disable, 1 to enable |
| gRoamOffloadEnabled=0 |
| |
| gAllowDFSChannelRoam=1 |
| |
| ############################################# |
| # Offload related configurations |
| ############################################# |
| # Beacon filtering frequency (unit in beacon intervals) |
| gNthBeaconFilter=50 |
| |
| # Enable WAPI or not |
| # WAPIIsEnabled=0 |
| # Flags to filter Mcast abd Bcast RX packets. |
| # Value 0: No filtering, 1: Filter all Multicast. |
| # 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast |
| McastBcastFilter=3 |
| |
| #Flag to enable HostARPOffload feature or not |
| hostArpOffload=1 |
| |
| #Flag to enable TCPChkSumOffld feature or not |
| gEnableTCPChkSumOffld=1 |
| |
| #Flag to enable HostNSOffload feature or not |
| hostNSOffload=1 |
| |
| #Flag to enable IPChkSumOffld feature or not |
| gEnableIPChecksumOffload=1 |
| |
| # controlling the following offload patterns |
| # through ini parameter. Default value is 1 |
| # to disable set it to zero. ssdp = 0 |
| # Setup multicast pattern for mDNS 224.0.0.251, |
| # SSDP 239.255.255.250 and LLMNR 224.0.0.252 |
| ssdp = 0 |
| |
| #Enable MC address filtering offload |
| gMCAddrListEnable=1 |
| |
| # Enable Active mode offload |
| gActiveModeOffload=1 |
| |
| # Enable Active mode offload |
| gEnableActiveModeOffload=1 |
| |
| #Maximum number of offload peers supported |
| # gMaxOffloadPeers=2 |
| |
| # WOW Enable/Disable. |
| # 0 - Disable both magic pattern match and pattern byte match. |
| # 1 - Enable magic pattern match on all interfaces. |
| # 2 - Enable pattern byte match on all interfaces. |
| # 3 - Enable both magic patter and pattern byte match on all interfaces. |
| # Default value of gEnableWoW is 3. |
| # gEnableWoW=0 |
| |
| #IPA config |
| gIPAEnable=0x00 |
| gIPADescSize=800 |
| gIPAPreFilterEnable=1 |
| gIPARMEnable=1 |
| gIPAIPv6Enable=1 |
| |
| |
| ############################################# |
| # Logging related configurations |
| ############################################# |
| gEnableLogp=1 |
| |
| gEnableSelfRecovery=1 |
| |
| #Enable firmware log |
| gEnablefwlog=1 |
| # Additional firmware log levels |
| gFwDebugLogLevel=4 |
| gFwDebugModuleLoglevel=1,0,2,0,4,0,5,0,6,0,7,4,8,0,9,0,11,0,13,0,17,0,18,0,19,0,27,0,29,0,31,0,35,0,36,0,38,0 |
| |
| #Enable firmware uart print |
| gEnablefwprint=0 |
| |
| ############################################# |
| # TDLS related configurations |
| ############################################# |
| # Enable support for TDLS |
| # 0 - disable |
| # 1 - enable |
| gEnableTDLSSupport=1 |
| |
| # Enable support for Implicit Trigger of TDLS. That is, wlan driver shall |
| # initiate TDLS Discovery towards a peer whenever setup criteria (throughput |
| # and RSSI) is met and then will initiate teardown when teardown criteria |
| # (idle packet count and RSSI) is met. |
| # 0 - disable |
| # 1 - enable |
| gEnableTDLSImplicitTrigger=1 |
| |
| # Enable TDLS External Control. That is, user space application has to |
| # first configure a peer MAC in wlan driver towards which TDLS is desired. |
| # Device will establish TDLS only towards those configured peers whenever |
| # TDLS criteria (throughput and RSSI threshold) is met and teardown TDLS |
| # when teardown criteria (idle packet count and RSSI) is met. However, |
| # device will accept TDLS connection if it is initiated from any other peer, |
| # even if that peer is not configured. |
| # 0 - disable |
| # 1 - enable |
| # For TDLS External Control, Implicit Trigger must also be enabled. |
| gTDLSExternalControl=1 |
| |
| # Enable support for TDLS off-channel operation |
| # 0 - disable |
| # 1 - enable |
| # TDLS off-channel operation will be invoked when there is only one |
| # TDLS connection. |
| gEnableTDLSOffChannel=1 |
| |
| gEnableTDLSScan=1 |
| gTDLSTxStatsPeriod=500 |
| gTDLSTxPacketThreshold=10 |
| gTDLSIdlePacketThreshold=1 |
| |
| ############################################# |
| # P2P related configurations |
| ############################################# |
| #P2P Listen offload |
| gEnableP2pListenOffload=1 |
| |
| #Enable or Disable p2p device address administered |
| isP2pDeviceAddrAdministrated=0 |
| |
| #Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). |
| #For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) |
| #For both active and power save clients. |
| |
| #Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. |
| #If doesn't honor for 5 seconds then DUT remove client. |
| |
| #Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on |
| #11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. |
| #Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. |
| |
| #gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period |
| #where we send NULL frame. |
| |
| #gApLinkMonitorPeriod = 10 |
| #gGoLinkMonitorPeriod = 10 |
| |
| #gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. |
| #Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. |
| gGoKeepAlivePeriod = 20 |
| gApKeepAlivePeriod = 20 |
| |
| ############################################# |
| # SAP related configurations |
| ############################################# |
| #Enable OBSS protection |
| gEnableApOBSSProt=1 |
| |
| #Enable/Disable UAPSD for SoftAP |
| gEnableApUapsd=1 |
| |
| # SAP auto channel selection configuration |
| # 0 = disable auto channel selection |
| # 1 = enable auto channel selection, channel provided by supplicant will be ignored |
| gApAutoChannelSelection=0 |
| |
| #SOFTAP Channel Range selection |
| gAPChannelSelectStartChannel=1 |
| gAPChannelSelectEndChannel=11 |
| |
| # SAP Country code |
| # Default Country Code is 2 bytes, 3rd byte is optional indoor or out door. |
| # Example |
| # US Indoor, USI |
| # Korea Outdoor, KRO |
| # Japan without optional byte, JP |
| # France without optional byte, FR |
| #gAPCntryCode=USI |
| |
| # DFS Master Capability |
| gEnableDFSMasterCap=1 |
| |
| # Disable 11AC for hotspot |
| gSapForce11NFor11AC=1 |
| |
| #Auto Shutdown Value in seconds. A value of 0 means Auto shutoff is disabled |
| gAPAutoShutOff=0 |
| |
| # Remove Overlap channel restriction |
| gEnableOverLapCh=0 |
| |
| # Enable/Disable channel avoidance for SAP in SCC scenario |
| # 0 - disable |
| # 1 - enable |
| gSapSccChanAvoidance=0 |
| |
| #Set priority for connection with bssid_hint |
| g_is_bssid_hint_priority=0 |
| END |
| |
| # Note: Configuration parser would not read anything past the END marker |
