## This file is used by NFC NXP NCI HAL(external/libnfc-nci/halimpl/pn54x)
## and NFC Service Java Native Interface Extensions (packages/apps/Nfc/nci/jni/extns/pn54x)

###############################################################################
# Application options
# Logging Levels
# NXPLOG_DEFAULT_LOGLEVEL    0x01
# ANDROID_LOG_DEBUG          0x03
# ANDROID_LOG_WARN           0x02
# ANDROID_LOG_ERROR          0x01
# ANDROID_LOG_SILENT         0x00
#
NXPLOG_EXTNS_LOGLEVEL=0x01
NXPLOG_NCIHAL_LOGLEVEL=0x01
NXPLOG_NCIX_LOGLEVEL=0x01
NXPLOG_NCIR_LOGLEVEL=0x01
NXPLOG_FWDNLD_LOGLEVEL=0x01
NXPLOG_TML_LOGLEVEL=0x01
NFC_DEBUG_ENABLED=0

###############################################################################
# Nfc Device Node name
NXP_NFC_DEV_NODE="/dev/pn551"

###############################################################################
# Extension for Mifare reader enable
MIFARE_READER_ENABLE=0x01

###############################################################################
# Firmware file type
#.so file   0x01
#.bin file  0x02
NXP_FW_TYPE=0x01

###############################################################################
# System clock source selection configuration
#define CLK_SRC_XTAL       1
#define CLK_SRC_PLL        2
NXP_SYS_CLK_SRC_SEL=0x01

###############################################################################
# System clock frequency selection configuration
#define CLK_FREQ_13MHZ         1
#define CLK_FREQ_19_2MHZ       2
#define CLK_FREQ_24MHZ         3
#define CLK_FREQ_26MHZ         4
#define CLK_FREQ_38_4MHZ       5
#define CLK_FREQ_52MHZ         6
NXP_SYS_CLK_FREQ_SEL=0x01

###############################################################################
# The timeout value to be used for clock request acknowledgment
# min value = 0x01 to max = 0x06
NXP_SYS_CLOCK_TO_CFG=0x06

###############################################################################
# NXP proprietary settings
NXP_ACT_PROP_EXTN={2F, 02, 00}

###############################################################################
# NFC forum profile settings
NXP_NFC_PROFILE_EXTN={20, 02, 05, 01, A0, 44, 01, 00}

###############################################################################
# NXP TVDD configurations settings
# Allow NFCC to configure External TVDD, There are currently three
#configurations (1, 2 and 3) are supported, out of them only one can be
#supported.
NXP_EXT_TVDD_CFG=0x02

#config1:SLALM, 3.3V for both RM and CM
NXP_EXT_TVDD_CFG_1={20, 02, 0B, 02, A0, 66, 01, 00, A0, 0E, 03, 02, 09, 00}

#config2: use DCDC in CE, use Tx_Pwr_Req, set CFG2 mode, SLALM,
#monitoring 5V from DCDC, 3.3V for both RM and CM, DCDCWaitTime=4.2ms
NXP_EXT_TVDD_CFG_2={20, 02, 0B, 02, A0, 66, 01, 00, A0, 0E, 03, 56, 40, 0A }

###############################################################################
# NXP RF ALMSL configuration settings for FW VERSION = 10.05.02
#
#    A0, 0D, 03, 00, 40, 01                RF_CLIF_CFG_BOOT            CLIF_ANA_NFCLD_REG
#    A0, 0D, 03, 04, 47, 02                RF_CLIF_CFG_INITIATOR       CLIF_ANA_AGC_REG
#    A0, 0D, 03, 06, 47, 02                RF_CLIF_CFG_TARGET          CLIF_ANA_AGC_REG
#    A0, 0D, 06, 06, 03, 00, 6D, 00, 20    RF_CLIF_CFG_TARGET          CLIF_TRANSCEIVE_CONTROL_REG
#    A0, 0D, 06, 06, 42, 00, 02, FF, FF    RF_CLIF_CFG_TARGET          CLIF_ANA_TX_AMPLITUDE_REG
#    A0, 0D, 03, 06, 37, 08                RF_CLIF_CFG_TARGET          CLIF_TX_CONTROL_REG
#    A0, 0D, 06, 32, 42, F8, 10, FF, FF    RF_CLIF_CFG_BR_106_I_TXA    CLIF_ANA_TX_AMPLITUDE_REG
#    A0, 0D, 06, 34, 2D, 24, 47, 0C, 00    RF_CLIF_CFG_BR_106_I_RXA_P  CLIF_SIGPRO_RM_CONFIG1_REG
#    A0, 0D, 04, 34, 44, 21, 00            RF_CLIF_CFG_BR_106_I_RXA_P  CLIF_ANA_RX_REG
#    A0, 0D, 04, 46, 44, 26, 00            RF_CLIF_CFG_BR_106_I_RXB    CLIF_ANA_RX_REG
#    A0, 0D, 06, 46, 2D, 15, 25, 0D, 00    RF_CLIF_CFG_BR_106_I_RXB    CLIF_SIGPRO_RM_CONFIG1_REG
#    A0, 0D, 06, 44, 42, 88, 10, FF, FF    RF_CLIF_CFG_BR_106_I_TXB    CLIF_ANA_TX_AMPLITUDE_REG
#    A0, 0D, 06, 56, 2D, 05, 9E, 0C, 00    RF_CLIF_CFG_BR_212_I_RXF_P  CLIF_SIGPRO_RM_CONFIG1_REG
#    A0, 0D, 04, 56, 44, 22, 00            RF_CLIF_CFG_BR_212_I_RXF_P  CLIF_ANA_RX_REG
#    A0, 0D, 06, 5C, 2D, 05, 9E, 0C, 00    RF_CLIF_CFG_BR_424_I_RXF_P  CLIF_SIGPRO_RM_CONFIG1_REG
#    A0, 0D, 04, 5C, 44, 26, 00            RF_CLIF_CFG_BR_424_I_RXF_P  CLIF_ANA_RX_REG
#    A0, 0D, 06, 54, 42, 88, 10, FF, FF    RF_CLIF_CFG_BR_212_I_TXF    CLIF_ANA_TX_AMPLITUDE_REG
#    A0, 0D, 06, 5A, 42, 90, 10, FF, FF    RF_CLIF_CFG_BR_424_I_TXF    CLIF_ANA_TX_AMPLITUDE_REG
#    A0, 0D, 06, 98, 42, 00, 02, FF, FF    RF_CLIF_CFG_GTM_B           CLIF_ANA_TX_AMPLITUDE_REG
#    A0, 0D, 06, 6C, 44, A3, 90, 03, 00    RF_CLIF_CFG_BR_106_T_RXA    CLIF_ANA_RX_REG
#    A0, 0D, 06, 7C, 44, A3, 90, 03, 00    RF_CLIF_CFG_BR_106_T_RXB    CLIF_ANA_RX_REG
#    A0, 0D, 06, 8E, 44, 12, 90, 03, 00    RF_CLIF_CFG_BR_212_T_RXF    CLIF_ANA_RX_REG
#    A0, 0D, 06, 94, 44, 12, 90, 03, 00    RF_CLIF_CFG_BR_424_T_RXF    CLIF_ANA_RX_REG
#    A0, 0D, 06, 24, 42, 00, 02, FF, FF    RF_CLIF_CFG_TECHNO_T_TXA_P  CLIF_ANA_TX_AMPLITUDE_REG
# *** ALMSL FW VERSION = 10.05.02 ***
NXP_RF_CONF_BLK_1={
    20, 02, C5, 18,
    A0, 0D, 03, 00, 40, 03,
    A0, 0D, 03, 04, 47, 02,
    A0, 0D, 03, 06, 47, 02,
    A0, 0D, 06, 06, 03, 00, 6F, 00, 20,
    A0, 0D, 06, 06, 42, 00, 00, F8, F8,
    A0, 0D, 03, 06, 37, 08,
    A0, 0D, 06, 32, 42, F8, 10, FF, FF,
    A0, 0D, 06, 34, 2D, 24, 47, 0C, 00,
    A0, 0D, 04, 34, 44, 21, 00,
    A0, 0D, 04, 46, 44, 26, 00,
    A0, 0D, 06, 46, 2D, 15, 25, 0D, 00,
    A0, 0D, 06, 44, 42, 88, 10, FF, FF,
    A0, 0D, 06, 56, 2D, 05, 5E, 0C, 00,
    A0, 0D, 04, 56, 44, 21, 00,
    A0, 0D, 06, 5C, 2D, 05, 9E, 0C, 00,
    A0, 0D, 04, 5C, 44, 26, 00,
    A0, 0D, 06, 54, 42, 88, 10, FF, FF,
    A0, 0D, 06, 5A, 42, 90, 10, FF, FF,
    A0, 0D, 06, 98, 42, 00, 00, F8, F8,
    A0, 0D, 06, 6C, 44, A3, 90, 03, 00,
    A0, 0D, 06, 7C, 44, A3, 90, 03, 00,
    A0, 0D, 06, 8E, 44, 12, 90, 03, 00,
    A0, 0D, 06, 94, 44, 12, 90, 03, 00,
    A0, 0D, 06, 24, 42, 00, 00, F8, F8
}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
NXP_RF_CONF_BLK_2={
    20, 02, 71, 03,
    A0, 1D, 11, 53, 33, 14, 17, 00, AA, 85, 00, 80, 55, 2A, 04, 00, 63, 00, 00, 00,
    A0, 1E, 11, 1B, 13, 14, 14, 00, 6F, 97, 00, 00, 00, 10, 04, 00, 63, 02, 00, 00,
    A0, 92, 45, 23, 04, 50, 10, 00, 19, 00, 14, 00, 92, 00, 08, 00, 01, 01, 09, 00, 4B, 01, 0A, 00, FF, 83, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00, 00 
}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
NXP_RF_CONF_BLK_3={
    20, 02, 2E, 05,
    A0, 0D, 06, 00, 35, 50, 00, FF, 02,
    A0, 0D, 06, 04, 35, F4, 01, F4, 01,
    A0, 0D, 06, 06, 35, FF, 03, FF, 03,
    A0, 0D, 06, 07, 35, FF, 01, FF, 02,
    A0, 0D, 06, 10, 35, FF, 01, FF, 02
}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
#NXP_RF_CONF_BLK_4={
#}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
#NXP_RF_CONF_BLK_5={
#}

###############################################################################
# NXP RF configuration ALM/PLM settings
# This section needs to be updated with the correct values based on the platform
#NXP_RF_CONF_BLK_6={
#}

###############################################################################
# Core configuration extensions
# It includes
# Wired mode settings A0ED, A0EE
# Tag Detector A040, A041, A043
# Low Power mode A007
# Clock settings A002, A003
# PbF settings A008
NXP_CORE_CONF_EXTN={20, 02, 29, 0A,
    A0, 06, 01, 01,
    A0, 07, 01, 02,
    A0, EC, 01, 00,
    A0, ED, 01, 00,
    A0, 5E, 01, 01,
    A0, 40, 01, 01,
    A0, DD, 01, 2D,
    A0, 96, 01, 01,
    A0, 41, 01, 02,
    A0, 43, 01, 00
    }

###############################################################################
# Core configuration rf field filter settings to enable set to 01 to disable set to 00 last bit
NXP_CORE_RF_FIELD={ 20, 02, 05, 01, A0, 62, 01, 01
        }
###############################################################################
# To enable i2c fragmentation set i2c fragmentation enable 0x01 to disable set to 0x00
NXP_I2C_FRAGMENTATION_ENABLED=0x00

###############################################################################
# Core configuration settings
NXP_CORE_CONF={ 20, 02, 2A, 0E,
        28, 01, 00,
        21, 01, 00,
        30, 01, 08,
        31, 01, 03,
        32, 01, 60,
        38, 01, 01,
        33, 00,
        54, 01, 06,
        50, 01, 02,
        5B, 01, 00,
        80, 01, 01,
        81, 01, 01,
        82, 01, 0E,
        18, 01, 01
        }

###############################################################################
#Enable SWP full power mode when phone is power off
NXP_SWP_FULL_PWR_ON=0x00

###############################################################################
#Set the default Felica T3T System Code OffHost route Location :
# host  0x00
# UICC  0x02
# UICC2 0x03
DEFAULT_SYS_CODE_ROUTE=0x00

###############################################################################
#Set the default Felica T3T System Code :
DEFAULT_SYS_CODE={FE,FF}

###############################################################################
# AID Matching platform options
# AID_MATCHING_L 0x01
# AID_MATCHING_K 0x02
AID_MATCHING_PLATFORM=0x01

###############################################################################
#CHINA_TIANJIN_RF_SETTING
#Enable  0x01
#Disable 0x00
NXP_CHINA_TIANJIN_RF_ENABLED=0x01

###############################################################################
#SWP_SWITCH_TIMEOUT_SETTING
# Allowed range of swp timeout setting is 0x00 to 0x3C [0 - 60].
# Timeout in milliseconds, for example
# No Timeout  0x00
# 10 millisecond timeout 0x0A
NXP_SWP_SWITCH_TIMEOUT=0x0A

###############################################################################
# Extended APDU length for ISO_DEP
ISO_DEP_MAX_TRANSCEIVE=0xFEFF

###############################################################################
# Vendor Specific Proprietary Protocol & Discovery Configuration
# Set to 0xFF if unsupported
#  byte[0] NCI_PROTOCOL_18092_ACTIVE
#  byte[1] NCI_PROTOCOL_B_PRIME
#  byte[2] NCI_PROTOCOL_DUAL
#  byte[3] NCI_PROTOCOL_15693
#  byte[4] NCI_PROTOCOL_KOVIO
#  byte[5] NCI_PROTOCOL_MIFARE
#  byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
#  byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
#  byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
NFA_PROPRIETARY_CFG={05, FF, FF, 06, 81, 80, 70, FF, FF}

###############################################################################
# Choose the presence-check algorithm for type-4 tag.  If not defined, the default value is 1.
# 0  NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
# 1  NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
# 2 NFA_RW_PRES_CHK_ISO_DEP_NAK; Type - 4 tag protocol iso-dep nak presence check
#    command is sent waiting for rsp and ntf.
PRESENCE_CHECK_ALGORITHM=1

###############################################################################