| # This file allows user to override the factory |
| # defaults for the WLAN Driver |
| |
| ############################################# |
| # Power related configurations |
| ############################################# |
| # Phy Mode (auto, b, g, n, etc) |
| # Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac |
| # 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only |
| # 7 = 11b only 8 = 11ac only. |
| gDot11Mode=0 |
| |
| ############################################# |
| # STA related general configurations |
| ############################################# |
| # UAPSD service interval for VO,VI, BE, BK traffic |
| InfraUapsdVoSrvIntv=0 |
| InfraUapsdViSrvIntv=0 |
| InfraUapsdBeSrvIntv=0 |
| InfraUapsdBkSrvIntv=0 |
| |
| # Flag to allow STA send AddTspec even when ACM is Off |
| gAddTSWhenACMIsOff=1 |
| |
| ############################################# |
| # SAP related configurations |
| ############################################# |
| #Enable OBSS protection |
| gEnableApOBSSProt=1 |
| |
| # RTS threshold |
| RTSThreshold=1048576 |
| |
| # 802.11d support |
| g11dSupportEnabled=0 |
| |
| # DFS Master Capability |
| gEnableDFSMasterCap=0 |
| |
| gNeighborLookupThreshold=76 |
| |
| # Legacy (non-ESE, non-802.11r) Fast Roaming Support |
| # To enable, set FastRoamEnabled=1 |
| # To disable, set FastRoamEnabled=0 |
| FastRoamEnabled=1 |
| |
| # Check if the AP to which we are roaming is better than current AP in |
| # terms of RSSI. Checking is disabled if set to Zero.Otherwise it will |
| # use this value as to how better the RSSI of the new/roamable AP should |
| # be for roaming |
| RoamRssiDiff=3 |
| |
| #Channel Bonding |
| gChannelBondingMode5GHz=1 |
| |
| # Enable DFS channel roam |
| # 0: DISABLE, 1: ENABLED_NORMAL, 2: ENABLED_ACTIVE |
| gAllowDFSChannelRoam=1 |
| |
| # chain mask related params |
| # |
| # Set txchainmask and rxchainmask |
| # These parameters are used only if gEnable2x2 is 0 |
| # Valid values are 1,2 |
| # Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. |
| # Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. |
| gSetTxChainmask1x1=1 |
| gSetRxChainmask1x1=1 |
| |
| # MCC to SCC Switch mode: |
| # 0-Disable |
| # 1-Enable |
| # 2-Force SCC if same band, with SAP restart |
| # 3-Force SCC if same band, without SAP restart by sending (E)CSA |
| # 4-Force SCC if same band (or) use SAP mandatory channel for DBS, |
| # without SAP restart by sending (E)CSA |
| gWlanMccToSccSwitchMode = 3 |
| |
| # 1=enable tx STBC; 0=disable |
| gEnableTXSTBC=1 |
| |
| # 1=enable rx LDPC; 0=disable |
| gEnableRXLDPC=1 |
| |
| #Enable/Disable Tx beamformee in SAP mode |
| gEnableTxBFeeSAP=1 |
| |
| # Enable Tx beamforming in VHT20MHz |
| # Valid values are 0,1. If commented out, the default value is 0. |
| # 0=disable, 1=enable |
| gEnableTxBFin20MHz=1 |
| |
| # 802.11K support |
| gRrmEnable=1 |
| |
| #Enable Power Save offload |
| gEnablePowerSaveOffload=2 |
| |
| # Maximum Receive AMPDU size (VHT only. Valid values: |
| # 0->8k 1->16k 2->32k 3->64k 4->128k) |
| gVhtAmpduLenExponent=7 |
| |
| # Maximum MPDU length (VHT only. Valid values: |
| # 0->3895 octets, 1->7991 octets, 2->11454 octets) |
| gVhtMpduLen=2 |
| |
| ############################################# |
| # P2P related configurations |
| ############################################# |
| #Enable or Disable p2p device address administered |
| isP2pDeviceAddrAdministrated=0 |
| |
| #Mac address provisioning |
| enable_mac_provision=1 |
| |
| #Enable VHT on 2.4Ghz |
| gEnableVhtFor24GHzBand=1 |
| |
| ############################################# |
| # Offload related configurations |
| ############################################# |
| |
| # controlling the following offload patterns |
| # through ini parameter. Default value is 1 |
| # to disable set it to zero. ssdp = 0 |
| # Setup multicast pattern for mDNS 224.0.0.251, |
| # SSDP 239.255.255.250 and LLMNR 224.0.0.252 |
| ssdp=0 |
| |
| # Regulatory Setting; 0=STRICT; 1=CUSTOM |
| gRegulatoryChangeCountry=1 |
| |
| # Disable/Enable GreenAP |
| # 0 to disable, 1 to enable, default: 1 |
| gEnableGreenAp=0 |
| |
| #Enable/Disable LPASS support |
| # 0 to disable, 1 to enable |
| gEnableLpassSupport=1 |
| |
| # Whether userspace country code setting shld have priority |
| gCountryCodePriority=1 |
| |
| # Enable or Disable Multi-user MIMO |
| # 1=Enable (default), 0=Disable |
| gEnableMuBformee=1 |
| |
| # Inactivity time (in ms) to end TX Service Period while in IBSS power save mode |
| gIbssTxSpEndInactivityTime=10 |
| |
| ############################################# |
| # TDLS related configurations |
| ############################################# |
| # Enable support for TDLS |
| # 0 - disable |
| # 1 - enable |
| gEnableTDLSSupport=1 |
| |
| # Enable support for Implicit Trigger of TDLS. That is, wlan driver shall |
| # initiate TDLS Discovery towards a peer whenever setup criteria (throughput |
| # and RSSI) is met and then will initiate teardown when teardown criteria |
| # (idle packet count and RSSI) is met. |
| # 0 - disable |
| # 1 - enable |
| gEnableTDLSImplicitTrigger=1 |
| |
| # Enable support for TDLS off-channel operation |
| # 0 - disable |
| # 1 - enable |
| # TDLS off-channel operation will be invoked when there is only one |
| # TDLS connection. |
| gEnableTDLSOffChannel=1 |
| |
| # Tx/Rx Packet threshold for initiating TDLS. |
| # This ini is used to configure the number of Tx/Rx packets during the period of |
| # gTDLSTxStatsPeriod when exceeded, a TDLS Discovery request is triggered. |
| gTDLSTxPacketThreshold=10 |
| |
| # Number of idle packet. |
| # This ini is used to configure the number of Tx/Rx packet, below which |
| # within last gTDLSTxStatsPeriod period is considered as idle condition. |
| gTDLSIdlePacketThreshold=1 |
| |
| # VHT Tx/Rx MCS values |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gVhtRxMCS=2 |
| gVhtTxMCS=2 |
| |
| # VHT Tx/Rx MCS values for 2x2 |
| # Valid values are 0,1,2. If commented out, the default value is 0. |
| # 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 |
| gEnable2x2=1 |
| gVhtRxMCS2x2=2 |
| gVhtTxMCS2x2=2 |
| |
| #IPA config is a bit mask and following are the configurations. |
| #bit0 IPA Enable |
| #bit1 IPA PRE Filter enable |
| #bit2 IPv6 enable |
| #bit3 IPA Resource Manager (RM) enable |
| #bit4 IPA Clock scaling enable |
| #bit5 IPA uC ENABLE |
| #bit6 IPA uC STA ENABLE |
| #bit8 IPA Real Time Debugging |
| gIPAConfig=0x7d |
| |
| # Enable Rx handling options |
| # Rx_thread=1 RPS=2(default for ROME) NAPI=4(default for ihelium) |
| # Rx_thread + NAPI = 5 |
| rx_mode=5 |
| |
| # Enable(Tx) fastpath for data traffic. |
| # 1 - enable(default) 0 - disable |
| gEnableFastPath=1 |
| |
| # Enable TCP Segmentation Offload |
| # 1 - enable 0 - disable |
| TSOEnable=1 |
| |
| # Enable Generic Receive Offload |
| # LRO and GRO are exclusive to each other |
| # LRO support is deprecated on latest 4.9(SDM845) kernel |
| # 1 - enable(default) 0 - disable |
| GROEnable=1 |
| |
| # Enable HT MPDU Density |
| # 4 for 2 micro sec |
| ght_mpdu_density=4 |
| |
| # Enable flow steering to enable multiple CEs for Rx flows. |
| # Multiple Rx CEs<==>Multiple Rx IRQs<==>probably different CPUs. |
| # Parallel Rx paths. |
| # 1 - enable 0 - disable(default) |
| gEnableFlowSteering=1 |
| |
| # Time in microseconds after which a NAPI poll must yield |
| ce_service_max_yield_time=500 |
| |
| #Maximum number of HTT messages to be processed per NAPI poll |
| ce_service_max_rx_ind_flush=1 |
| |
| # Maximum number of MSDUs the firmware will pack in one HTT_T2H_MSG_TYPE_RX_IN_ORD_PADDR_IND |
| maxMSDUsPerRxInd=8 |
| ################ Datapath feature set End ################ |
| |
| ################ NAN feature set start ################### |
| |
| # Enable NAN discovery (NAN 1.0) |
| # 1 - enable 0 - disable(default) |
| gEnableNanSupport=1 |
| ################ NAN feature set end ##################### |
| |
| hostscan_adaptive_dwell_mode=1 |
| |
| # Create another interface during driver load |
| gEnableConcurrentSTA=wlan1 |
| |
| #Enable/Disable dual MAC feature |
| # 0 - enable DBS |
| # 1 - disable DBS |
| # 2 - disable DBS for connection but keep DBS for scan |
| # 3 - disable DBS for connection but keep DBS scan with async |
| # scan policy disabled |
| # 4 - enable DBS for connection as well as for scan with async |
| # scan policy disabled |
| # 5 - enable DBS for connection but disable dbs for scan. |
| # 6 - enable DBS for connection but disable simultaneous scan from |
| # upper layer (DBS scan remains enabled in FW). |
| gDualMacFeatureDisable=6 |
| |
| #Enable/Disable latency mode |
| # 0 disable |
| # 1 enable |
| wlm_latency_enable=1 |
| |
| # Enable/Disable NUD Tracking within driver |
| gEnableNUDTracking=0 |
| |
| # Configure hardware filter for DTIM mode |
| # The hardware filter is only effective in DTIM mode. |
| # Use this configuration to blanket drop broadcast/multicast packets at the hardware level |
| # without waking up the firmware |
| # |
| # Takes a bitmap of frame types to drop |
| # |
| # 0 = disable feature |
| # 1 = drop all broadcast frames, except ARP (default) |
| # 2 = drop all multicast frames, except ICMPv6 |
| # 3 = drop all broadcast and multicast frames, except ARP and ICMPv6 |
| gHwFilterMode=0 |
| |
| # Enables SNR Monitoring |
| # This ini is used to set default snr monitor |
| gEnableSNRMonitoring=1 |
| |
| # Control to enable TCP limit output byte |
| # This ini is used to enable dynamic configuration of TCP limit output bytes |
| # tcp_limit_output_bytes param. |
| # Enabling this will let driver post message to cnss-daemon, |
| # accordingly cnss-daemon will modify the tcp_limit_output_bytes. |
| gTcpLimitOutputEnable=0 |
| |
| # Enable Target Wake Time support. |
| # This ini is used to enable or disable TWT support. |
| enable_twt=0 |
| |
| # For NLO/PNO, enable MAWC based scan |
| # Enable/Disable the Motion Aided Wireless Connectivity based NLO using this parameter |
| mawc_nlo_enabled=0 |
| |
| # Force 1x1 when connecting to certain peer |
| # This INI when enabled will force 1x1 connection with certain peer. |
| gForce1x1Exception=0 |
| |
| # Enable/disable oce feature for STA |
| # This ini is used to enable/disable oce feature for STA |
| oce_sta_enable=0 |
| |
| # Enable/disable oce feature for SAP |
| # This ini is used to enable/disable oce feature for SAP |
| oce_sap_enable=0 |
| |
| # Set probe request rate |
| # This ini is used to set probe request rate to 5.5Mbps as per OCE requirement in 2.4G band |
| oce_enable_probe_req_rate=0 |
| |
| # HE caps Weightage to calculate best candidate |
| # This ini is used to increase/decrease HE caps weightage in best candidate selection. |
| # If AP supports HE caps, AP will get additional weightage with this param. |
| # Weightage will be given only if dot11mode is HE capable. |
| he_caps_weightage=0 |
| |
| # PCL Weightage to calculate best candidate |
| # This ini is used to increase/decrease PCL weightage in best candidate selection. |
| # If some APs are in PCL list, those AP will get addition weightage. |
| pcl_weightage=10 |
| |
| # Enable/disable esp feature |
| # This ini is used to enable/disable ESP(Estimated service parameters) IE parsing and decides |
| # whether firmware will include this in its scoring algo. |
| enable_esp_for_roam=0 |
| |
| # Bitmask to enable 11k offload to FW. |
| # This ini is used to set which of the 11k features is offloaded to FW |
| # Currently Neighbor Report Request is supported for offload and is enabled by default. |
| # B0: Offload 11k neighbor report requests |
| # B1-B31: Reserved |
| 11k_offload_enable_bitmask=0 |
| |
| # Set channel selection logic for different concurrency combinations to DBS or inter band MCC. |
| # Default is DBS for STA+STA and STA+P2P. |
| # 0 - inter-band MCC |
| # 1 - DBS |
| # |
| # BIT 0: STA+STA |
| # BIT 1: STA+P2P |
| # BIT 2-31: Reserved |
| channel_select_logic_conc=0 |
| |
| # Configure BTM |
| # Bit 0: Enable/Disable the BTM offload. Set this to 1 will enable and 0 will disable BTM offload. |
| # BIT 2, 1: Action on non matching candidate with cache. If a BTM request is received from AP |
| # then the candidate AP's may/may-not be present in the firmware scan cache. |
| # Based on below config firmware will decide whether to forward BTM frame to host or |
| # consume with firmware and proceed with Roaming to candidate AP. |
| # |
| # 00 scan and consume |
| # 01 no scan and forward to host |
| # 10, 11 reserved |
| # BIT 5, 4, 3: Roaming handoff decisions on multiple candidates match |
| # 000 match if exact BSSIDs are found |
| # 001 match if at least one top priority BSSID only |
| # 010, 011, 100, 101, 110, 111 reserved |
| # BIT 6: Set this to 1 will send BTM query frame and 0 not sent. |
| # BIT 7-31: Reserved |
| btm_offload_config=0 |
| |
| #Timer waiting for interface up from the upper layer |
| gInterfaceChangeWait=2000 |
| |
| # Set external ACS Policy to Mandatory |
| acs_policy=1 |
| |
| # Set Modulated Dtim |
| gEnableModulatedDTIM=2 |
| |
| # Enable NAN datapath |
| genable_nan_datapath=1 |
| |
| # Set MaxLIModulate Dtim |
| gMaxLIModulatedDTIM=6 |
| |
| # Used for ignore peer infrormation |
| gIgnorePeerErpInfo=1 |
| |
| # DBS Scan Selection |
| gdbs_scan_selection=5,4,1,16,4,1 |
| |
| # 0 - Disallow STA+SAP SCC on LTE coex channel |
| # 1 - Allow STA+SAP SCC on LTE coex channel |
| g_sta_sap_scc_on_lte_coex_chan=1 |
| |
| # Tx Chain Mask for CCK |
| gCckChainMaskEnable=1 |
| |
| # Tx Chain Mask for 1SS |
| gTxChainMask1ss=0 |
| |
| # TPC power |
| gSelfGenFrmPwr=3 |
| |
| # Enable LFR3 subnet detection |
| gLFRSubnetDetectionEnable=0 |
| |
| #Enable APF in Active mode |
| gActiveUcBpfMode=2 |
| |
| # Control MC/BC active APF mode |
| gActiveMcBcBpfMode=1 |
| |
| # Enable or disable Probe Req Information Element whitelist. When enabled, IEs corresponding to bits |
| # set in bitmaps are allowed in probe request, all others removed while device is unassociated |
| # with an AP |
| # 1=Enable, 0=Disable (default) |
| g_enable_probereq_whitelist_ies=1 |
| |
| # ie bitmap examples: <bitmap_name>=<value> [<Allowed Information elements>] |
| # g_probe_req_ie_bitmap_0=0x80000009 #[0, 3, 31] |
| # g_probe_req_ie_bitmap_0=0x00000000 #[] (default) |
| # g_probe_req_ie_bitmap_1=0x80000009 #[32, 35, 63] |
| g_probe_req_ie_bitmap_0=0x0000000B |
| g_probe_req_ie_bitmap_1=0x00040000 |
| # g_probe_req_ie_bitmap_2=0x00000000 |
| # g_probe_req_ie_bitmap_3=0x00000000 |
| # g_probe_req_ie_bitmap_4=0x00000000 |
| # g_probe_req_ie_bitmap_5=0x00000000 |
| g_probe_req_ie_bitmap_6=0x20000000 |
| # g_probe_req_ie_bitmap_7=0x00000000 |
| |
| # Used to specify vendor specific OUIs |
| gProbeReqOUIs=0050F208 |
| |
| # enable 11d in world mode |
| enable_11d_in_world_mode=1 |
| |
| # WLM flags setting for low level |
| wlm_latency_flags_low=0xc08 |
| |
| #Enable/Disable chain selection optimization for one chain dtim |
| #Min: 0 |
| #MAX: 30 |
| gEnableDTIMSelectionDiversity=3 |
| |
| # Enable/Disable rtt sta mac randomization |
| enable_rtt_mac_randomization=1 |
| |
| # Set max time for active 2G channel scan |
| active_max_channel_time_2g=40 |
| |
| # To config roaming scan policy |
| roaming_scan_policy=1 |
| |
| # Config DPTRACE |
| gDptraceConfig=1,6,2,126 |
| |
| # Enable/Disable peer unmap confirmation support in Host |
| gEnablePeerUnmapConfSupport=1 |
| |
| END |
| |
| # Note: Configuration parser would not read anything past the END marker |
| |
