blob: 3b125b5df575b7c2d588cee4e81e2beb868b0384 [file] [log] [blame]
########################### Start of libnf-hal-st_aosp.conf ###########################
###############################################################################
###############################################################################
# ST HAL trace log level
STNFC_HAL_LOGLEVEL=1
NFC_DEBUG_ENABLED=0
###############################################################################
# Vendor specific mode to enable FW (RF & SWP) traces.
STNFC_FW_DEBUG_ENABLED=0
###############################################################################
# File used for NFA storage
NFA_STORAGE="/data/nfc"
###############################################################################
# Keep the nfa storage file.
PRESERVE_STORAGE=1
###############################################################################
# In Switch OFF mode (phone switched-off), specify the desired CE mode to
# the controller.
# 0: No card-emulation; DEFAULT
# 1: Switch-off card-emulation enabled
CE_ON_SWITCH_OFF_STATE=1
###############################################################################
# Vendor specific mode to support the USB charging mode if VPSIO=1 in switch off.
STNFC_USB_CHARGING_MODE=1
###############################################################################
# Vendor Specific Proprietary Protocol & Discovery Configuration
# Set to 0xFF if unsupported
# byte[0] NCI_PROTOCOL_18092_ACTIVE
# byte[1] NCI_PROTOCOL_B_PRIME
# byte[2] NCI_PROTOCOL_DUAL
# byte[3] NCI_PROTOCOL_15693
# byte[4] NCI_PROTOCOL_KOVIO
# byte[5] NCI_PROTOCOL_MIFARE
# byte[6] NCI_DISCOVERY_TYPE_POLL_KOVIO
# byte[7] NCI_DISCOVERY_TYPE_POLL_B_PRIME
# byte[8] NCI_DISCOVERY_TYPE_LISTEN_B_PRIME
NFA_PROPRIETARY_CFG={05:FF:FF:06:8A:90:77:FF:FF}
###############################################################################
# Choose the presence-check algorithm for type-4 tag. If not defined,
# the default value is 1.
# 0 NFA_RW_PRES_CHK_DEFAULT; Let stack selects an algorithm
# 1 NFA_RW_PRES_CHK_I_BLOCK; ISO-DEP protocol's empty I-block
# 2 NFA_RW_PRES_CHK_RESET; Deactivate to Sleep, then re-activate
# 3 NFA_RW_PRES_CHK_RB_CH0; Type-4 tag protocol's ReadBinary command on channel 0
# 4 NFA_RW_PRES_CHK_RB_CH3; Type-4 tag protocol's ReadBinary command on channel 3
# 5 NFA_RW_PRES_CHK_ISO_DEP_NAK; presence check command ISO-DEP NAK as per NCI2.0
PRESENCE_CHECK_ALGORITHM=5
###############################################################################
# Name of the NCI HAL module to use
# If unset, falls back to nfc_nci.bcm2079x
NCI_HAL_MODULE="nfc_nci.st21nfc"
###############################################################################
# White list to be set at startup.
DEVICE_HOST_WHITE_LIST={02:C0}
###############################################################################
# BAIL OUT value for P2P
# Implements algorithm for NFC-DEP protocol priority over ISO-DEP protocol.
POLL_BAIL_OUT_MODE=1
###############################################################################
# Extended APDU length for ISO_DEP
ISO_DEP_MAX_TRANSCEIVE=0xFEFF
###############################################################################
# Configure the NFC Extras to open and use a static pipe. If the value is
# not set or set to 0, then the default is use a dynamic pipe based on a
# destination gate (see NFA_HCI_DEFAULT_DEST_GATE). Note there is a value
# for each EE (ESE/SIM)
OFF_HOST_ESE_PIPE_ID=0x5E
OFF_HOST_SIM_PIPE_ID=0x3E
###############################################################################
#Set the default Felica T3T System Code OffHost route Location :
#This settings will be used when application does not set this parameter
# host 0x00
# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
# UICC 0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_SYS_CODE_ROUTE=0x86
###############################################################################
#Set the Felica T3T System Code supported power state:
DEFAULT_SYS_CODE_PWR_STATE=0x3B
###############################################################################
# Path and Files used for FW update binaries storage
STNFC_FW_PATH_STORAGE="/vendor/firmware"
STNFC_FW_BIN_NAME="/st54j_fw.bin"
STNFC_FW_CONF_NAME="/st54j_conf_G6QU3.bin"
###############################################################################
# Default off-host route for Felica.
# This settings will be used when application does not set this parameter
# host 0x00
# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
# UICC 0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_NFCF_ROUTE=0x86
###############################################################################
# Configure the default off-host route.
# used for technology A and B routing
# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
# UICC 0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_OFFHOST_ROUTE=0x81
###############################################################################
# Configure the default AID route.
# host 0x00
# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
# UICC 0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_ROUTE=0x00
###############################################################################
# Configure the NFCEEIDs of offhost UICC.
# UICC 0x81 (UICC_1), 0x85 (UICC_2)
OFFHOST_ROUTE_UICC={81}
###############################################################################
# Configure the NFCEEIDs of offhost eSEs.
# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
OFFHOST_ROUTE_ESE={86}
###############################################################################
# Configure the list of NFCEE for the ISO-DEP routing.
# host 0x00
# eSE 0x82 (eSE), 0x86 (eUICC/SPI-SE)
# UICC 0x81 (UICC_1), 0x85 (UICC_2)
DEFAULT_ISODEP_ROUTE=0x81
###############################################################################
# Core configuration settings
CORE_CONF_PROP={ 20, 02, 0a, 03,
a1, 01, 1e,
a2, 01, 19,
80, 01, 01
}