/** | |
* \file | |
* | |
* \brief USB configuration file | |
* | |
* Copyright (C) 2009 Atmel Corporation. All rights reserved. | |
* | |
* \page License | |
* | |
* Redistribution and use in source and binary forms, with or without | |
* modification, are permitted provided that the following conditions are met: | |
* | |
* 1. Redistributions of source code must retain the above copyright notice, | |
* this list of conditions and the following disclaimer. | |
* | |
* 2. Redistributions in binary form must reproduce the above copyright notice, | |
* this list of conditions and the following disclaimer in the documentation | |
* and/or other materials provided with the distribution. | |
* | |
* 3. The name of Atmel may not be used to endorse or promote products derived | |
* from this software without specific prior written permission. | |
* | |
* 4. This software may only be redistributed and used in connection with an | |
* Atmel AVR product. | |
* | |
* THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED | |
* WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF | |
* MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE | |
* EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR | |
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL | |
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR | |
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER | |
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT | |
* LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY | |
* OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH | |
* DAMAGE. | |
*/ | |
#ifndef _CONF_USB_H_ | |
#define _CONF_USB_H_ | |
#include "compiler.h" | |
#include "nvm.h" | |
/* Redefine USB interrupt vectors base address to safe code space */ | |
# if defined(__GNUC__) | |
# error GCC no supported when interrupt vectors space is optimized | |
/* | |
# undef USB_BUSEVENT_vect | |
# undef USB_TRNCOMPL_vect | |
# undef USB_BUSEVENT_vect_num | |
# undef USB_TRNCOMPL_vect_num | |
# define USB_BUSEVENT_vect_num 1 | |
# define USB_BUSEVENT_vect _VECTOR(1) | |
# define USB_TRNCOMPL_vect_num 2 | |
# define USB_TRNCOMPL_vect _VECTOR(2) | |
*/ | |
# elif defined(__ICCAVR__) | |
# undef USB_BUSEVENT_vect | |
# undef USB_TRNCOMPL_vect | |
# define USB_BUSEVENT_vect 0x0 | |
# define USB_TRNCOMPL_vect 0x4 | |
# endif | |
/** | |
* USB Device Configuration | |
* @{ | |
*/ | |
//! Device definition (mandatory) | |
#define USB_DEVICE_VENDOR_ID USB_VID_ATMEL | |
#if part_is_defined(ATxmega128A1U) | |
#define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_ATXMEGA128A1U | |
#if (FLASH_SIZE>0x10000) // Optimize code space (Boot = 4KB) Temporary to support 64A1U | |
#define USB_DEVICE_PRODUCT_NAME "DFU ATXMEGA128A1U" | |
#endif | |
#elif part_is_defined(ATxmega641U) | |
#define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_ATXMEGA64A1U | |
//#define USB_DEVICE_PRODUCT_NAME "DFU ATXMEGA64A1U" // To safe code space | |
#elif part_is_defined(ATxmega128B1) | |
#define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_ATXMEGA128B1 | |
#define USB_DEVICE_PRODUCT_NAME "DFU ATXMEGA128B1" | |
#elif part_is_defined(ATxmega256A3U) || part_is_defined(ATxmega256A3BU) | |
#define USB_DEVICE_PRODUCT_ID USB_PID_ATMEL_DFU_ATXMEGA256A3_U_BU | |
#define USB_DEVICE_PRODUCT_NAME "DFU ATXMEGA256A3_U_BU" | |
#else | |
#error Unknow DFU PID for this AVR part | |
#endif | |
#define USB_DEVICE_MAJOR_VERSION (BOOTLOADER_VERSION>>4) | |
#define USB_DEVICE_MINOR_VERSION (BOOTLOADER_VERSION&0x0F) | |
#define USB_DEVICE_POWER 100 // Consumption on Vbus line (mA) | |
#if (FLASH_SIZE>0x10000) // Optimize code space (Boot = 4KB) | |
#define USB_DEVICE_MANUFACTURE_NAME "ATMEL" | |
#endif | |
#define USB_DEVICE_ATTR USB_CONFIG_ATTR_SELF_POWERED | |
/** | |
* Device speeds support | |
* Only Full speed is authorized on DFU ATMEL | |
* Because FLIP supports only full speed | |
* Also: | |
* - low speed is too slow (endpoint 8 Bytes) | |
* - high speed does not increase flash program speed | |
* - high speed is not supported on custom board with bad USB layout | |
* @{ | |
*/ | |
// No speed change possible | |
//@} | |
/** | |
* USB Device Callbacks definitions (Optional) | |
* @{ | |
*/ | |
#define UDC_VBUS_EVENT(b_vbus_high) // NO VBUS EVENT on XMEGA | |
//@} | |
//@} | |
/** | |
* USB Interface Configuration | |
* @{ | |
*/ | |
/** | |
* Configuration of DFU interface | |
* @{ | |
*/ | |
//! Interface callback definition | |
#define UDI_DFU_ENABLE_EXT() true | |
#define UDI_DFU_DISABLE_EXT() | |
//! Version of ATMEL protocol used | |
#define UDI_DFU_ATMEL_PROTOCOL_VERSION DFU_ATMEL_PROTOCOL_VERSION_2 | |
//@} | |
//@} | |
/** | |
* USB Device Driver Configuration | |
* @{ | |
*/ | |
#define UDD_NO_SLEEP_MGR | |
//@} | |
//! The includes of classes and other headers must be done at the end of this file to avoid compile error | |
#include "udi_dfu_atmel_conf.h" | |
#include "conf_isp.h" // Need to put bootloader version at USB device version | |
#endif // _CONF_USB_H_ |